Ethyl acrylate-methacrylic acid copolymer

In the agglomeration step, the latexes are partially agglomerated using a core/shell agglomerating agent latex, which consists of an elastomeric 1,3-butadiene/slyrene copolymer core and an ethyl acrylate/methacrylic acid copolymer shell. This partial agglomeration operation should not be confused with a coagulation operation where the emulsion is fully destabilized (13). 

Details are given of the preparation of model ethyl acrylate-methacrylic acid copolymer latices by non-seeded semicontinuous emulsion copolymerisation. Polydispersity was examined using dynamic and static light scattering. Correlations between hydrodynamic volume and viscosity properties of the dispersions are discussed. The different character of the particle structure was confirmed by differences in particle disintegration after alkali addition or in the presence of methanol. 19 refs. 

The freeze/thaw (F/T) stability of a polymer emulsion serves as a macroscopic probe for investigating the properties of the average particle in a polymer emulsion. A review of the factors which contribute to this stability is included. A study of styrene-ethyl acrylate-methacrylic acid polymers shows the existence of a minimum in the plot of minimum weight percent acid required for F/T stability vs. the minimum film formation temperature (MFT) of the polymer. This is considered to be a function of both the amount of associated surfactant and the minimum acid content. Thus, both the type of surfactant and the copolymer ratio—i.e., MFT—play major roles. Chain transfer between radicals and polyether surfactant resulting in covalently bonded surfactant-polymer combinations is important in interpreting the results. 

Methyl Methacrylate—Ethyl Acrylate—Methacrylic Acid (MMA—EA— MAA) Terpolymers. In an earlier paper (22, 23) values for the MFT of each of a series of acrylic copolymer emulsions were obtained by calculating Tff values using the equation of Wood (34), ignoring the presence of methacrylic acid. These were then converted to MFT values using available literature data (20, 24) and by extrapolating and interpolating the straight line obtained. The MFT values for these identical emulsions at pH 9.5 have now been determined experimentally, and these data are compared in Table II. Values for MFT s below 0°C. could not be obtained experimentally. 

To this end, work has been initiated on a series of somewhat less polar styrene-ethyl acrylate-methacrylic acid emulsion polymers. The first major difference encountered in changing from the MMA-EA-MAA to the S-EA-MAA polymers was the need for at least a 50% increase in surfactant to obtain a coagulate-free emulsion for the 100% styrene vs. 100% methyl methacrylate. The determination of the minimum weight percent of MAA required to yield a F/T stable emulsion for various copolymers gave the results listed in Table III. 

Butyl acrylate-butyl methacrylate-methacrylic acid copolymer Methyl methacrylate-ethyl acrylate-methacryhc acid copolymer Poly(sodium 10-undecenyl sulfate) (polySUS)... 

Orientations in elongated mbbers are sometimes regular to the extent that there is local crystallization of individual chain segments (e.g., in natural rubber). X-ray diffraction patterns of such samples are very similar to those obtained from stretched fibers. The following synthetic polymers are of technical relevance as mbbers poly(acrylic ester)s, polybutadienes, polyisoprenes, polychloroprenes, butadiene/styrene copolymers, styrene/butadiene/styrene tri-block-copolymers (also hydrogenated), butadiene/acrylonitrile copolymers (also hydrogenated), ethylene/propylene co- and terpolymers (with non-conjugated dienes (e.g., ethylidene norbomene)), ethylene/vinyl acetate copolymers, ethyl-ene/methacrylic acid copolymers (ionomers), polyisobutylene (and copolymers with isoprene), chlorinated polyethylenes, chlorosulfonated polyethylenes, polyurethanes, silicones, poly(fluoro alkylene)s, poly(alkylene sulfide)s. 

ETHYL ACRYLATE-METHACRYLIC ACID EMULSION COPOLYMER PARTICLES... 

April 30,1986. Photopolymer positive surprint color proofing film based on epoxy acrylate monomer exhibits low dot gain, low time dependence of toning and good tonal range. Binder can be methyl-methacrylate/ethyl acrylate/acryhc acid copolymer, preferably crosslinked with zinc ions and plasticized with a second acrylate monomer and a mixture of triacetin and trimethylol propane. 

The ionic aggregates present in an ionomer act as physical crosslinks and drastically change the polymer properties. The blending of two ionomers enhances the compatibility via ion-ion interaction. The compatibilisation of polymer blends by specific ion-dipole and ion-ion interactions has recently received wide attention [93-96]. FT-IR spectroscopy is a powerful technique for investigating such specific interactions [97-99] in an ionic blend made from the acid form of sulfonated polystyrene and poly[(ethyl acrylate - CO (4, vinyl pyridine)]. Datta and co-workers [98] characterised blends of zinc oxide-neutralised maleated EPDM (m-EPDM) and zinc salt of an ethylene-methacrylic acid copolymer (Zn-EMA), wherein Zn-EMA content does not exceed 50% by weight. The blend behaves as an ionic thermoplastic elastomer (ITPE). Blends (Z0, Z5 and Z10) were prepared according to the following formulations [98] ... 

Eastacryl30D, Kollicoat MAE 30 D, and KollicoatMAE 30 DP are also aqueous dispersions of the anionic copolymer based on methacrylic acid and ethyl acrylate. The copolymer also corresponds to USPNF 23 methacrylic acid copolymer. Type C. The ratio of free-carboxyl groups to ester groups is 1 1. Films prepared from the copolymers dissolve above pH... 

EM 35. See Milk protein EM-40. See Glyceryl tall ate EM 65. See Sodium caseinate EM 375. See Milk protein EM-600. See PEG-12 tallate EM LV. See Sodium caseinate EM-PB EM-WS. See Lard oil EMA. See Ethylene/methyl acrylate copolymer Ethyl methacrylate Ethylene/MA copolymer EMA. See Methoxyethanol acetate EMAA. See Ethylene/methacrylic acid copolymer... 

Poly (ethylene-chlorotrifluoroethylene). See Ethylene/chlorotrifluoroethylene copolymer Poly (ethylene-co-acrylic acid). See Ethylene/acrylic acid copolymer Poly (ethylene-co-1-butene). See Ethylene/butene-1 copolymer Poly (ethylene-co-butyl acrylate). See Ethylene/butyl acrylate copolymer Poly (ethylene-co-carbon monoxide). See Ethylene/carbon monoxide copolymer Poly (ethylene-co-ethyl acrylate). See Ethylene/ethyl acrylate copolymer Poly (ethylene-co-methacrylic acid). See Ethylene/methacrylic acid copolymer Poly (ethylene-co-methyl acrylate). See Ethylene/methyl acrylate copolymer Poly (ethylene-co-methyl acrylate-co-acrylic acid). See Ethylene/methyl acrylate/acrylic acid terpolymer... 

Azelaic acid Dimer acid, hydrogenated Ethylene/ethyl acrylate copolymer Ethylene/methacrylic acid copolymer Hydroxystearic acid... 

Acrylates/hydroxyesters acrylates copolymer Acrylates/PVP copolymer t-Butylacrylate/ethylacrylate/methacrylic acid copolymer Isobutylene/MA copolymer Methacrylic acid copolymer Octylacrylamide/acrylates/butylaminoethyl methacrylate copolymer Polymethacrylamidopropyl trimonium chloride Polyquaternium-29 PVM/MA copolymer, ethyl ester PVP PVP/d i methylam i noethyl methacrylate copolymer Sodium p-styrenesulfonate VA/butyl maleate/isobornyl acrylate copolymer Vinyl acetate/crotonic acid copolymer Vinyl... 

Compatibilized blends of ethylene-methacrylic acid copolymer and PS were prepared by Kim et al. (1998) through addition of S-co-4-vinylpyridine. Similarly, blends of poly(isobutyl methacrylate) were compatibilized with poly(styrene-co-methacrylic acid) using poly(isobutyl methacrylate-co-2-(A, A -dimethylamino) ethyl methacrylate) or poly(isobutyl methacrylate-co-4-vinylpyridine) (Habi and Djadoun 1999). Turcsayii (1995) has reported compatibilized blends of PE-g-(N-vinylimidazole) with acrylic acid-modified PP. 

Some specific recent applications of the chromatography-mass spectrometry technique to various types of polymers include the following PE [130, 131], poly(l-octene), poly(l-decene), poly(l-dodecene) and 1-octene-l-decene-l-dodecene terpolymer [132], chlorinated polyethylene [133], polyolefins [134,135], acrylic acid, methacrylic acid copolymers [136, 137], polyacrylate [138], styrene-butadiene and other rubbers [139-141], nitrile rubber [142], natural rubbers [143,144], chlorinated natural rubber [145,146], polychloroprene [147], PVC [148-150], silicones [151,152], polycarbonates (PC) [153], styrene-isoprene copolymers [154], substituted PS [155], polypropylene carbonate [156], ethylene-vinyl acetate copolymer [157], Nylon 6,6 [158], polyisopropenyl cyclohexane-a-methylstyrene copolymers [195], cresol-novolac epoxy resins [160], polymeric flame retardants [161], poly(4-N-alkylstyrenes) [162], pol)winyl pyrrolidone [31,163], vinyl pyrrolidone-methacryloxysilicone copolymers [164], polybutylcyanoacrylate [165], polysulfide copolymers [1669], poly(diethyl-2-methacryloxy) ethyl phosphate [167, 168], ethane-carbon monoxide copolymers [169], polyetherimide [170], and bisphenol-A [171]. 

Carboxy-terminated nitrile rubber Elastomeric copolymer from ethylene and ethyl acrylate Ethylene-glycidyl methacrylate copolymer Copolymer from ethylene and methacrylic acid Copolymer from ethylene and methylmethacrylate... 

Water (Isopropyl alcohol can also be used) Wax, silicone and nonionic surface active agent are used as anti foaming agents. Acrylic polymer Emulsion of acrylic polymer Ethylene oxide polymer Hydroxyl ethyl Cellulose Methyl cellulose Polyvinyl alcohol Isocyanate Wax wetting agent Aqueous urethane. Salt of methacrylic acid copolymer Wax emulsion Emulsion of ethylene-vinyl acetate eopolviner ... 

Nevertheless, several conunercial grades of moderate impact strength polyamides have been produced for a long time by simple melt blending with such impact modifiers as ethylene-ethyl acrylate, ethylene-acrylic acid copolymers and ionomers based on zinc neutralized, ethylene-methacrylic acid copolymers [15-16]. However, in the case of the PA-6, the zinc ionomers have been found to be particularly effective as impact modifiers... 

A number of acrylic resins are used for bonding cloth, plastics, leather and, in some cases, metal foils. The acrylic monomers most commonly used in adhesives are ethyl acrylate, methyl acrylate, methacrylic acid, acrylic acid, acrylamide, and acrylonitrile. The polymers or copolymers are soluble in common organic solvents and can be supplied in much the same manner as other solvent-based systems. In addition, the polymers are soluble in the monomers. When a catalyst is added, monomers polymerize, thus providing good bonding to glass and to plastic surfaces of similar composition (e.g., polymethylmethacrylate). " ... 

A variety of ionomers have been described in the research literature, including copolymers of a) styrene with acrylic acid, b) ethyl acrylate with methacrylic acid, and (c) ethylene with methacrylic acid. A relatively recent development has been that of fluorinated sulfonate ionomers known as Nafions, a trade name of the Du Pont company. These ionomers have the general structure illustrated (10.1) and are used commercially as membranes. These ionomers are made by copolymerisation of the hydrocarbon or fluorocarbon monomers with minor amounts of the appropriate acid or ester. Copolymerisation is followed by either neutralisation or hydrolysis with a base, a process that may be carried out either in solution or in the melt. 

Partially saponified poly(vinyl acetate) Fully saponified poly(vinyl acetate) Copolymers with crotonic acid Copolymers with vinyl acetate with methacrylic acid with acrylic acid esters with acrylonitrile with styrene with ethyl vinyl ether with butadiene... 

The carboxylated polymers [476,499] include acrylic, methacrylic or maleic acid polymers (all obviously anionic in character) applied mainly from aqueous emulsion and particularly in combination with crease-resist or durable press resins. This type of chemistry has already been discussed in section 10.8.2. A particularly common example is the copolymer of acrylic acid with ethyl acrylate (10.247). In general the best balance of properties is obtained with 75-85% ethyl acrylate (y) and 25-15% acrylic acid (x), with an average chain length of about 1300 (x + y) units 65-85% ethyl acrylate with 35-15% methacrylic acid is also suitable. When the content of the acidic comonomer increases above about 30% the durability to washing tends to decrease, whilst longer chains tend to give a stiffer handle [499]. 

Figure 41. A plot of sensitivity to Mo (5.4k) x-ray radiation and 20 kV electron beam radiation for several resists. EPB is epoxidized polybutadiene, P(GMA-EA) is a copolymer of glycidyl methacrylate and ethyl acrylate (COP), PGMA is poly (glycidyl methacrylate), PBS is poly (butene-1 -sulfone), FBM-1 is poly (2,2,3,3-tetrafluoropropyl methacrylate), P(MMA-MA) is a copolymer of methyl methacrylate and methacrylic acid, PMMA is poly (methyl methacrylate). (Reproduced with permission from Ref. 56J...

Since the 1950s, synthetic polymers have been used as art binders. The most common groups are referred to as the vinyls and acrylics by artists. Both groupings represent a wide variety of polymers and copolymers and are inaccurately, or at best not accurately, named. For polymer scientists, the term vinyl generally refers to PVC, but to artists it may refer to many other materials. Even so, most of the synthetic paint market today is based on acrylics. Acrylic paints are typically water emulsions of synthetic polymers. In art, the term acrylic is used to describe a wide variety of polymers and copolymers that can be considered as derivatives of acrylic acids. Most acrylics used in art binders are PMMA (Equation 6.61), PVAc (Equation 6.64), poly( -butyl methacrylate) (Equation 6.65), and copolymers such as poly(ethyl acrylate-comethacrylate). 

Close to 2 billion pounds of polymeric products based on acrylic and methacrylic esters are produced annually in the United States, about evenly divided between acrylates and methacrylates. A substantial fraction of the methacrylate products are copolymers. Most of the acrylate products are copolymers. The copolymers contain various combinations of acrylate and/or methacrylate monomers, including combinations of ester and acid monomers. Methyl methacrylate (MMA) is by far the most important methacrylate ester monomer, accounting for 90% of the volume of methacrylic ester monomers. Ethyl and n-butyl acrylates account for about 80% of the total volume of acrylate ester monomers. 

Graft copolymers of polyamides using pre-irradiation gamma-rays techniques have been reported for styrene (130), in solution, in the presence of water (40), in alcohols or acetone solution (131), vinyl acetate (130), methacrylic acid in water (132) or methanol solution (129), methyl (133) and ethyl (130) acrylates, 2-ethylhexyl acrylate (55,134), methyl methacrylate (130), in methanol solution (129), 2-dimethylamino ethyl methacrylate quaternary salts (135), acrylamide in aqueous medium (128,136), acrylonitrile (130,137), and 4-vinyl pyridine in aqueous solution (128). 

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... 

---