Copolymers acrylic

Acrylate copolymers Acrylate ester Acrylate esters Acrylate grouts Acrylate polymers Acrylates... 

Acrylic acid polymers Acrylic adhesives Acrylic anhydride Acrylic copolymer Acrylic-cotton blends Acrylic elastomers... 

Under conditions of extreme acidity or alkalinity, acryhc ester polymers can be made to hydroly2e to poly(acryhc acid) or an acid salt and the corresponding alcohol. However, acryhc polymers and copolymers have a greater resistance to both acidic and alkaline hydrolysis than competitive poly(vinyl acetate) and vinyl acetate copolymers. Even poly(methyl acrylate), the most readily hydroly2ed polymer of the series, is more resistant to alkah than poly(vinyl acetate) (57). Butyl acrylate copolymers are more hydrolytically stable than ethyl acrylate copolymers (58). 

Polyacrylate elastomers find limited use in hydrauhc systems and gasket apphcations because of their superior heat resistance compared to the nitrile mbbers (219,220). Ethylene—acrylate copolymers were introduced in 1975. The apphcations include transmission seals, vibration dampers, dust boots, and steering and suspension seals. Further details and performance comparisons with other elastomers are given in reference 221 (see also Elastomers, SYNTHETIC-ACRYLIC ELASTOTffiRS). 

Acrylonitrile—methyl acrylate—iadene terpolymers, by themselves, or ia blends with acrylonitrile—methyl acrylate copolymers, exhibit even lower oxygen and water permeation rates than the iadene-free copolymers (110,111). Terpolymers of acrylonitrile with iadene and isobutjlenealso exhibit excellent barrier properties (112), and permeation of gas and water vapor through acrylonitrile—styrene—isobutjleneterpolymers is also low (113,114). 

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

Styrene—acrylic copolymers provide latices with good water resistance and gloss potential in both interior and exterior latex paints. However, they are typically regarded as having limited exterior durabiUty compared to all-acryhc latex emulsions that are designed for exterior use. 

Copolymers of vinyUdene chloride and methyl acrylate have been studied by x-ray techniques (75). For example, the long period (lamellar thickness) for an 8.5 wt % methyl acrylate copolymer was found to be 9.2 nm by smaH-angle x-ray scattering. The unit cell is monoclinic, with a = 0.686 and c = 1.247 nm by wide-angle x-ray scattering. 

An extensive investigation of the dilute solution properties of several acrylate copolymers has been reported (80). The behavior is typical of flexible-backbone vinyl polymers. The length of the acrylate ester side chain has Httle effect on properties. 

Film and foil adhesives based on internally plastici2ed copolymer adhesives have been suggested. For instance, vinyl acetate—ethylene or vinyl acetate—acrylate copolymers may be used for adhesion of films to porous surfaces. For metallic foil adhesion, copolymers containing carboxylate functionahty are suggested. 

Most of the surface sizes used in North America are modified styrene maleic anhydride (SMA) copolymers. Commercially available materials include Scripset (Monsanto/Hercules Inc.), Cypres (Cytec), Sursize (Akzo Nobel), MSA (Morton), NovaCote (Georgia Pacific), and HTl (Hopton Technologies). Styrene acrylate emulsions that are commonly used include Jetsize and Unibond (Akzo Nobel), Basoplast (BASF), and Cypres (Cytec). Other materials used as surface sizes include acrylonitrile acrylate copolymer (Basoplast, BASF), stearylated melamine resin (Sequapel, Sequa), polyurethane (Graphsize, Vining Chemicals), and diisobutylene maleic anhydride copolymers (Baysynthol, Bayer). 

Fig. 14. Oxygen permeabiUties of vinyUdene chloride— -butyl acrylate copolymers (27). See Table 1 for unit conversion.

The most commonly used polymers are cellulose acetate phthalate [9004-38-0] (CAP), poly(vinyl acetate phthalate) [34481-48-6] (PVAP), hydroxypropylmethyl-ceUulosephthalate [71138-97-1] (HPMCP), and polymethacrylates (111) (see Cellulose esters). Acrylate copolymers are also available (112). Eigure 11 shows the dissolution behavior of some commercially available enteric materials. Some manufacturers supply grades designed to dissolve at specific pH values with increments as small as 0.5 pH unit (113). 

Interpenetrating networks have been made by co-curing polychloroprene with copolymers of 1-chloro-1,3-butadiene [627-22-5]. The 1-chloro-1,3-butadiene serves as a cure site monomer, providing a cure site similar to that already in polychloroprene. The butadiene copolymer with 1-chloro-1,3-butadiene (44) and an octyl acrylate copolymer (45) improved the low temperature brittieness of polychloroprene. The acrylate also improved oil resistance and heat resistance. 

Vinyl acrylic copolymers Tough Good Very good Very good (Alphatic, good aromatic, poor) Fair, ISO F Excellent Easy... 

Ethylene-ethyl acrylate copolymers are very similar to the ethylene-vinyl acetate copolymers. The former materials are considered to have higher abrasion resistance and heat resistance whilst the EVA have been considered to be tougher and of greater clarity. 

Earlier, successful attempts at physically crosslinking acrylic PSAs have been disclosed in the work of Husman et al. [98], Mancinelli and colleagues [99,100] and others. Instead of making ABA type structures, these authors studied and developed the use of high macromers in acrylic copolymers. Macromers are... 

Mixtures of monomers can be used to balance properties. This is possible due to the ease of copolymer formation via free-radical polymerization. The glass transition temperature of acrylic copolymers can be predicted from the weight fraction of the component monomers and the glass transition temperatures of the respective homopolymers [20]. Eq. 3 (commonly known as the Fox equation) is reported ... 

The homopolymers, which are formed from alkyl cyanoacrylate monomers, are inherently brittle. For applications which require a toughened adhesive, rubbers or elastomers can be added to improve toughness, without a substantial loss of adhesion. The rubbers and elastomers which have been used for toughening, include ethylene/acrylate copolymers, acrylonitrile/butadiene/styrene (ABS) copolymers, and methacrylate/butadiene/styrene (MBS) copolymers. In general, the toughening agents are incorporated into the adhesive at 5-20 wt.% of the monomer. 

An example of this improvement in toughness can be demonstrated by the addition of Vamac B-124, an ethylene/methyl acrylate copolymer from DuPont, to ethyl cyanoacrylate [24-26]. Three model instant adhesive formulations, a control without any polymeric additive (A), a formulation with poly(methyl methacrylate) (PMMA) (B), and a formulation with Vamac B-124 (C), are shown in Table 4. The formulation with PMMA, a thermoplastic which is added to modify viscosity, was included to determine if the addition of any polymer, not only rubbers, could improve the toughness properties of an alkyl cyanoacrylate instant adhesive. To demonstrate an improvement in toughness, the three formulations were tested for impact strength, 180° peel strength, and lapshear adhesive strength on steel specimens, before and after thermal exposure at 121°C. 

Another area of recent interest is covulcanization in block copolymers, thermoplastic rubbers, and elasto-plastic blends by developing an interpenetrating network (IPN). A classical example for IPN formation is in polyurethane elastomer blended acrylic copolymers [7]. 

ATBN - amine terminated nitrile rubber X - Flory Huggins interaction parameter CPE - carboxylated polyethylene d - width at half height of the copolymer profile given by Kuhn statistical segment length DMAE - dimethyl amino ethanol r - interfacial tension reduction d - particle size reduction DSC - differential scanning calorimetry EMA - ethylene methyl acrylate copolymer ENR - epoxidized natural rubber EOR - ethylene olefin rubber EPDM - ethylene propylene diene monomer EPM - ethylene propylene monomer rubber EPR - ethylene propylene rubber EPR-g-SA - succinic anhydride grafted ethylene propylene rubber... 

---