Ethyl copolymer

Figure 7. Preparation of synthetic lignin 16, ethylated copolymer of coniferyl alcohol 7 and arylglycerol-/ -syringaresinol ether 6. In 16, the rectangular enclosure represents an assumed structure of the moiety derived from 7.

Photo-induced electron transfer between [Ru(bpy)3]2+-like centres covalently bound to positively-charged polymers (N-ethylated copolymers of vinylpyridine and [Ru(bpy)2(MVbpy)]2+) and viologens or Fe (III) has been studied using laser flash photolysis techniques. It is found that the backbone affects the rates of excited state quenching, the cage escape yield, and the back electron transfer rate because of both electrostatic and hydrophobic interactions. The effect of ionic strength on the reactions has been studied. Data on the electron transfer reactions of [Ru(bpy)3]2+ bound electrostatically or covalently to polystyrenesulphonate are also presented. 

Viscosity data for the ethyl-copolymer, A, over the range a=0 to a = 1, reveal the typical electrostatic expansion behavior of a weak polyacid such as polyacrylic acid. Polymer B-II, on the other hand, exists in an abnormally compact state at low a. The curves for polymers B-I and B-III, excluded from Figure 1 for clarity, are identical in shape and differ only in relative magnitude. The five-fold increase in [f/] over the range 0.35[Pg.5]

ToF-SIMS is a very powerful tool for identifying plasticisers and lubricants which contribute to adhesive failure, as in case of the interface of poly (vinylacetate-ethyl) copolymer/PVC laminations, particularly when the compounds are present at or below the detection limits of either ATR-FTIR or XPS [202]. In one case, ToF-SIMS showed fragment masses m/z 71 and 149 (C4H70 and... 

Under conditions of extreme acidity or alkalinity, acryhc ester polymers can be made to hydroly2e to poly(acryhc acid) or an acid salt and the corresponding alcohol. However, acryhc polymers and copolymers have a greater resistance to both acidic and alkaline hydrolysis than competitive poly(vinyl acetate) and vinyl acetate copolymers. Even poly(methyl acrylate), the most readily hydroly2ed polymer of the series, is more resistant to alkah than poly(vinyl acetate) (57). Butyl acrylate copolymers are more hydrolytically stable than ethyl acrylate copolymers (58). 

A typical process for the preparation of a 94.8% ethyl acrylate—5.2% acryUc acid copolymer as an approximately 39% solution in ethyl acetate is given... 

Emulsion Polymerization. Emulsion polymerization is the most important industrial method for the preparation of acryhc polymers. The principal markets for aqueous dispersion polymers made by emulsion polymerization of acryhc esters are the paint, paper, adhesives, textile, floor pohsh, and leather industries, where they are used principally as coatings or binders. Copolymers of either ethyl acrylate or butyl acrylate with methyl methacrylate are most common. 

The Manufacture of Ethyl Acy late—Acylic Acid Copolymers, TMM-4S, Rohm and Haas Co., Philadelphia, Pa. 

SAN resins show considerable resistance to solvents and are insoluble in carbon tetrachloride, ethyl alcohol, gasoline, and hydrocarbon solvents. They are swelled by solvents such as ben2ene, ether, and toluene. Polar solvents such as acetone, chloroform, dioxane, methyl ethyl ketone, and pyridine will dissolve SAN (14). The interactions of various solvents and SAN copolymers containing up to 52% acrylonitrile have been studied along with their thermodynamic parameters, ie, the second virial coefficient, free-energy parameter, expansion factor, and intrinsic viscosity (15). 

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

Pentaerythritol in rosin ester form is used in hot-melt adhesive formulations, especially ethylene—vinyl acetate (EVA) copolymers, as a tackifier. Polyethers of pentaerythritol or trim ethyl ol eth an e are also used in EVA and polyurethane adhesives, which exhibit excellent bond strength and water resistance. The adhesives maybe available as EVA melts or dispersions (90,91) or as thixotropic, one-package, curable polyurethanes (92). Pentaerythritol spko ortho esters have been used in epoxy resin adhesives (93). The EVA adhesives are especially suitable for cellulose (paper, etc) bonding. 

Fig. 1. Functional monomers used in acrylamide copolymers. Methacrylamidopropyltrim ethyl ammonium chloride [51410-72-1] (1), acryloyloxyethyltrimethylammonium chioride [44992-01-0] (2), methacryloyloxyethyltrimethylammonium chloride [50339-78-1] (3), /V,/V-dimethy1aminoethy1 methacrylate [2867-47-2] (4), /V,/V-dimethylaminopropy1 acryl amide [3845-76-9] (5), diallyl dimethyl amm onium chloride...

Ethyl and butyl esters of poly(vinyl methyl ether)/maleic anhydride (PVM/MA) copolymer were introduced in the early 1960s for use in hair sprays. These polymers also have free carboxy acid groups that can be neutralized. Recommended neutralization is 10%, but products can be found in the range of 5—30%, and recommended neutralizers include ammonium hydroxide, aminomethyl propanol, and triisopropano1 amine. These were the most widely used polymers in hair sprays before their use decreased dramatically in the early 1990s. 

The alcohols, proprietary denatured ethyl alcohol and isopropyl alcohol, are commonly used for E-type inks. Many E-type inks benefit from the addition of small amounts of ethyl acetate, MEK, or normal propyl acetate to the solvent blends. Aromatic hydrocarbon solvents are used for M-type inks. Polystyrene resins are used to reduce the cost of top lacquers. T-type inks are also reduced with aromatic hydrocarbons. Acryflc resins are used to achieve specific properties for V-type inks. Vehicles containing vinyl chloride and vinyl acetate copolymer resins make up the vinyl ink category. Ketones are commonly used solvents for these inks. 

Polymer Modification. The introduction of functional groups on polysdanes using the alkah metal coupling of dichlorosilanes is extremely difficult to achieve. Some polymers and copolymers with 2-(3-cyclohexenyl)ethyl substituents on siUcon have been made, and these undergo hydrogen hahde addition to the carbon—carbon double bond (94,98). 

Strong Base Anion Exchangers. As ia the synthesis of weak base anion exchangers, strong base resias are manufactured from styrenic as well as acryhc copolymers. Those based on copolymers of styrene and divinylben2ene are chloromethylated and then aminated. These reactions are the same as for the styrenic weakbase resias. The esseatial differeace is the amine used for amination. Trimethyl amine [75-50-3] N(CH2)3, and /V, /V- dim ethyl eth a n ol amine [108-01 -0] (CH2)2NCH2CH20H, are most commonly used. Both form quaternary ammonium functional groups similar to (8). 

An a priori method for choosing a surfactant was attempted by several researchers (50) using the hydroph i1 e—1 ip oph i1 e balance or HLB system (51). In the HLB system a surfactant soluble in oil has a value of 1 and a surfactant soluble in water has a value of 20. Optimum HLB values have been reported for latices made from styrene, vinyl acetate, methyl methacrylate, ethyl acrylate, acrylonitrile, and their copolymers and range from 11 to 18. The HLB system has been criticized as being imprecise (52). 

The polyamides are soluble in high strength sulfuric acid or in mixtures of hexamethylphosphoramide, /V, /V- dim ethyl acetam i de and LiCl. In the latter, compHcated relationships exist between solvent composition and the temperature at which the Hquid crystal phase forms. The polyamide solutions show an abmpt decrease in viscosity which is characteristic of mesophase formation when a critical volume fraction of polymer ( ) is exceeded. The viscosity may decrease, however, in the Hquid crystal phase if the molecular ordering allows the rod-shaped entities to gHde past one another more easily despite the higher concentration. The Hquid crystal phase is optically anisotropic and the texture is nematic. The nematic texture can be transformed to a chiral nematic texture by adding chiral species as a dopant or incorporating a chiral unit in the main chain as a copolymer (30). 

AH-acryHc (100%) latex emulsions are commonly recognized as the most durable paints for exterior use. Exterior grades are usuaHy copolymers of methyl methacrylate with butyl acrylate or 2-ethyIhexyl acrylate (see Acrylic ester polymers). Interior grades are based on methyl methacrylate copolymerized with butyl acrylate or ethyl acrylate. AcryHc latex emulsions are not commonly used in interior flat paints because these paints typicaHy do not require the kind of performance characteristics that acryHcs offer. However, for interior semigloss or gloss paints, aH-acryHc polymers and acryHc copolymers are used almost exclusively due to their exceUent gloss potential, adhesion characteristics, as weU as block and print resistance. 

Copolymers of sodium acrylate with sodium 2-acrylamido-2-methylpropane sulfonate (AMPS) or /V, /V- dim ethyl acryl am i de (52) have been used to prepare cross-linked systems at high temperatures and salinity. Chromium cross-linked gels, prepared from a 3 1 blend of partially hydrolyzed... 

Intrinsic viscosity—molecular weight relationships have been obtained for copolymers in methyl ethyl ketone. The value for a 15 wt % ethyl acrylate (EA) copolymer is [77] = 2.88 x 10 . ... 

Poly(ethyl methacrylate) (PEMA) yields truly compatible blends with poly(vinyl acetate) up to 20% PEMA concentration (133). Synergistic improvement in material properties was observed. Poly(ethylene oxide) forms compatible homogeneous blends with poly(vinyl acetate) (134). The T of the blends and the crystaUizabiUty of the PEO depend on the composition. The miscibility window of poly(vinyl acetate) and its copolymers with alkyl acrylates can be broadened through the incorporation of acryUc acid as a third component (135). A description of compatible and incompatible blends of poly(vinyl acetate) and other copolymers has been compiled (136). Blends of poly(vinyl acetate) copolymers with urethanes can provide improved heat resistance to the product providing reduced creep rates in adhesives used for vinyl laminating (137). 

Poly(vinyl acetate) and its copolymers with ethylene are available as spray-dried emulsion soHds with average particle sizes of 2—20 p.m the product can be reconstituted to an emulsion by addition of water or it can be added directly to formulations, eg, concrete. The powders may be used to raise soHds of a lower soHds latex. Solutions of resin in methyl and ethyl alcohol at 2—50 wt % soHds are also available. 

PMVEMA, supphed as a white, fluffy powder, is soluble in ketones, esters, pyridine, lactams, and aldehydes, and insoluble in aUphatic, aromatic, or halogenated hydrocarbons, as well as in ethyl ether and nitroparaffins. When the copolymer dissolves in water or alcohols, the anhydride group is cleaved, forming the polymers in free acid form or the half-esters of the corresponding alcohol, respectively. Table 7 illustrates the commercially available alternating copolymers and derivatives. 

Another example of water-reducible acryhc resins is used in the interior linings of two-piece beverage cans. A graft copolymer of styrene, ethyl... 

---