Weight percent

Sulfur is the heteroatom most frequently found in crude oils (see Table 1.5). Sulfur concentrations can range from 0.1 to more than 8 weight percent moreover, this content is correlated with the gravity of the crude oil and, therefore, its quality (light or heavy). 

These products have molecular weights between 2000 and 10,000, well below those of additives improving the viscosity index (100,000). They are added in very small concentrations (0.01 to 0.3 weight percent) and at these concentrations they can lower the pour point 30°C. 

TABLE 8.17 Standard Reference Values pH for the Measurement of Acidity in 50 Weight Percent Methanol-Water... 

Weight percent (% w/w), volume percent (% v/v) and weight-to-volume percent... 

The units of concentration most frequently encountered in analytical chemistry are molarity, weight percent, volume percent, weight-to-volume percent, parts per million, and parts per billion. By recognizing the general definition of concentration given in equation 2.1, it is easy to convert between concentration units. 

The amount of oxalic acid in a sample of rhubarb was determined by reacting with Fe as outlined in reaction 2.2. In a typical analysis, the oxalic acid in 10.62 g of rhubarb was extracted with a suitable solvent. The complete oxidation of the oxalic acid to CO2 required 36.44 mb of 0.0130 M Fe. What is the weight percent of oxalic acid in the sample of rhubarb ... 

Using appropriate conservation principles, derive an equation relating the moles of C10H20N2S4 to the moles of NaOH. What is the weight percent C10H20N2S4 in a sample of Antabuse if the H2SO4 produced from a 0.4613-g portion reacts with 34.85 mb of 0.02500 M NaOH ... 

The weight percent C10H20N2S4 in the sample, therefore, is 0.32295 gCioH2oN2S4... 

A sample of an ore was analyzed for Cu as follows. A 1.25-g sample of the ore was dissolved in acid and diluted to volume in a 250-mb volumetric flask. A 20-mb portion of the resulting solution was transferred by pipet to a 50-mb volumetric flask and diluted to volume. An analysis showed that the concentration of Cu in the final solution was 4.62 ppm. What is the weight percent of Cu in the original ore ... 

Using X-ray diffraction, Karstang and Kvalhein reported a new method for determining the weight percent of kalonite in complex clay minerals To test the method, nine samples containing known amounts of kalonite were prepared and analyzed. The results (as %w/w kalonite) are shown. 

Directions are provided for preparing and using a simple coring device using PVC pipe. This experiment also details a procedure for determining the weight percent of organic material in sediments as a function of depth. 

An alloy of chromel containing Ni, Fe, and Cr was analyzed by a complexation titration using EDTA as the titrant. A 0.7176-g sample of the alloy was dissolved in ITNOa and diluted to 250 mb in a volumetric flask. A 50.00-mb aliquot of the sample, treated with pyrophosphate to mask the Fe and Cr, required 26.14 mb of 0.05831 M EDTA to reach the murexide end point. A second 50.00-mb aliquot was treated with hexamethylenetetramine to mask the Cr. Titrating with 0.05831 M EDTA required 35.43 mb to reach the murexide end point. Einally, a third 50.00-mb aliquot was treated with 50.00 mb of 0.05831 M EDTA, and back titrated to the murexide end point with 6.21 mb of 0.06316 M Cu +. Report the weight percents of Ni, fe, and Cr in the alloy. 

Weight percent copolymer Temperature (°C) and relative height (arbitrary units) ... 

Percent of theoretical O2 absorbed Weight percent composition in reaction mixture ... 

The weight percent propylene in ethylene-propylene copolymers for different Ziegler-Natta catalysts was measuredt for the initial polymer produced from identical feedstocks. The following results were obtained ... 

Catalyst components Weight percent propylene Catalyst components Weight percent propylene... 

The particle sizes of fillers are usually collected and ordered to yield size distributions which are frequendy plotted as cumulative weight percent finer than vs diameter, often given as esd, on a log probabiUty graph. In this manner, most unmodified fillers yield a straight-line relationship or log normal distribution. Inspection of the data presented in this manner can yield valuable information about the filler. The coarseness of a filler is often quantified as the esd at the 99.9% finer-than value. Deviations from linearity at the high and low ends of the plot suggest that either fractionation has occurred to remove coarse or fine particles or the data are suspect in these ranges. 

G-5 Aliphatic Petroleum Resins. Carbocationic polymerization of C-5 feedstreams has been accomptished with various Friedel-Crafts catalyst systems. Table 3 compares the efficiencies of selected Lewis acids ia the polymerization of a typical C-5 stream containing 43 wt % C-5—C-6 diolefias and 47 wt % C-5—C-6 olefins (20). Based on weight percent yield of resia at equimolar coaceatratioas of catalyst (5.62 mmol/100 g), efficieacy follows AICI3 AlBr3 > BF3etherate-H20 > TiCfy > SnCl. The most commonly used catalyst in petroleum resin synthesis is AlCl. ... 

The second form consists of Pt metal but the iridium is present as iridium dioxide. Iridium metal may or may not be present, depending on the baking temperature (14). Titanium dioxide is present in amounts of only a few weight percent. The analysis of these coatings suggests that the platinum metal acts as a binder for the iridium oxide, which in turn acts as the electrocatalyst for chlorine discharge (14). In the case of thermally deposited platinum—iridium metal coatings, these may actually form an intermetallic. Both the electrocatalytic properties and wear rates are expected to differ for these two forms of platinum—iridium-coated anodes. 

---