Aspirators

Power output is controlled, not by adjusting the quantity of fuel/air mixture as in the case of induced spark ignition engines, but in changing the flow of diesel fuel introduced in a fixed volume of air. The work required to aspirate the air is therefore considerably reduced which contributes still more to improve the efficiency at low loads. 

Fig. 11-13. Apparatus for measuring the time dependence of interfacial tension (from Ref. 34). The air and aspirator connections allow for establishing the desired level of ftesh surface. IV denotes the Wilhelmy slide, suspended from a Cahn electrobalance with a recorder output.

A surfactant mixture having an HLB number of 8 should give a good W/O emulsion in which the oil phase is lanolin. Suggest two possible surfactant mixtures that you, an aspiring cosmetic chemist, might use you have been told that your formulations must contain 10% cetyl alcohol. 

The other vacuum option is a simple little aspirator that attaches to ones faucet or hose. This 15 device pulls a decent vacuum however, it is not an option at all in Strike s book. Running one of these babies 10-12 hrs a day is a despicable waste of a community s water supply. 

Procedure for filtering through a filtering crucible. The trap is used to prevent water from a water aspirator from backwashing into the suction flask. 

Precision For absorbances greater than 0.1-0.2, the relative standard deviation for atomic absorption is 0.3-1% for flame atomization, and 1-5% for electrothermal atomization. The principal limitation is the variation in the concentration of free-analyte atoms resulting from a nonuniform rate of aspiration, nebulization, and atomization in flame atomizers, and the consistency with which the sample is heated during electrothermal atomization. 

One problem with the analysis of salt samples is their tendency to clog the aspirator and burner assembly. What effect would this have on the analysis ... 

Clogging the aspirator and burner assembly decreases the rate of aspiration, decreasing the analyte s concentration in the flame. The result is a decrease in the signal and the introduction of a determinate error. 

Sensitivity Sensitivity in flame atomic emission is strongly influenced by the temperature of the excitation source and the composition of the sample matrix. Normally, sensitivity is optimized by aspirating a standard solution and adjusting the flame s composition and the height from which emission is monitored until the emission intensity is maximized. Chemical interferences, when present, decrease the sensitivity of the analysis. With plasma emission, sensitivity is less influenced by the sample matrix. In some cases, for example, a plasma calibration curve prepared using standards in a matrix of distilled water can be used for samples with more complex matrices. 

Horizontally Mixing Aspirator Aerators. An aerator using a horizontally mixing aspirator has a marine propeller, submerged under water, attached to a soHd or a hoUow shaft. The other end of the shaft is out of the water and attached to an electric motor. When the propeller is rotated at high velocity, at either 1800 or 3600 rpm, a pressure drop develops around the propeller. Air is then aspirated under the water and mixed with the water, and moved out. This type of aerator, shown ia Figure 3g, is very efficient ia mixing wastewater. 

Primary human skin irritation of tetradecanol, hexadecanol, and octadecanol is nil they have been used for many years ia cosmetic creams and ointments (24). Based on human testing and iudustrial experience, the linear, even carbon number alcohols of 6—18 carbon atoms are not human skin sensitizers, nor are the 7-, 9- and 11-carbon alcohols and 2-ethylhexanol. Neither has iudustrial handling of other branched alcohols led to skin problems. Inhalation hazard, further mitigated by the low vapor pressure of these alcohols, is slight. Sustained breathing of alcohol vapor or mist should be avoided, however, as aspiration hazards have been reported (25). 

Beckman Elutriation Method. The Beckman elutriation method uses a chamber designed so that the centrifugal effect of the radial inward fluid flow is constant (Fig. 3). The separation chambers are made of transparent epoxy resin which faciUtates observation of the movements of the cell boundary in strobe light illumination. This enables detection of the radius at which the cells are separating. When a mixture of cells, eg, mononuclear white cells, enters the chamber, separation can be achieved by fine tuning centrifuge speed and inward fluid flow to the specific cell group. This is a laboratory method suitable for relatively small numbers of cells. Chambers are available in sizes to handle 2-3 x 10 , 1 2 x 10 , and 1 x 10 ° cells. The Beckman chambers can be appHed to collect mononuclear cells from bone marrow aspirates. 

Article of Manufacture. An article of manufacture is an iavention such as a two-headed tooth bmsh, an iatravenous fluid bag, or an optical fiber "made" by a machine. One example of an iavention which could be considered an article of manufacture is U.S. Patent No. 5,241,990 tided "Irrigation/Aspiration Valve and Probe for Laparoscopy" (2). 

Jet Pumps. A jet pump is a clever way of using a high pressure motive fluid and a venturi to aspire a low pressure fluid to an intermediate pressure level. 

Highly sensitive iastmmental techniques, such as x-ray fluorescence, atomic absorption spectrometry, and iaductively coupled plasma optical emission spectrometry, have wide appHcation for the analysis of silver ia a multitude of materials. In order to minimize the effects of various matrices ia which silver may exist, samples are treated with perchloric or nitric acid. Direct-aspiration atomic absorption (25) and iaductively coupled plasma (26) have silver detection limits of 10 and 7 l-lg/L, respectively. The use of a graphic furnace ia an atomic absorption spectrograph lowers the silver detection limit to 0.2 l-ig/L. 

A method suitable for analysis of sulfur dioxide in ambient air and sensitive to 0.003—5 ppm involves aspirating a measured air sample through a solution of potassium or sodium tetrachloromercurate, with the resultant formation of a dichlorosulfitomercurate. Ethylenediaminetetraacetic acid (EDTA) disodium salt is added to this solution to complex heavy metals which can interfere by oxidation of the sulfur dioxide. The sample is also treated with 0.6 wt % sulfamic acid to destroy any nitrite anions. Then the sample is treated with formaldehyde and specially purified acid-bleached rosaniline containing phosphoric acid to control pH. This reacts with the dichlorosulfitomercurate to form an intensely colored rosaniline—methanesulfonic acid. The pH of the solution is adjusted to 1.6 0.1 with phosphoric acid, and the absorbance is read spectrophotometricaHy at 548 nm (273). 

Ga.s Eeeders. Chlorine gas is usually fed from a chlorine cylinder equipped with a pressure gauge, reducing valve, regulating valve, feed-rate indicator, and aspirator-type injector for dissolving the chlorine gas in water. The feeder can be manually, or more desirably automatically, controlled utili2ing continuous amperometric or potentiometric measurement of the free chlorine residual. The chlorine solution is normally introduced into the return line to the filter. 

Cefuroxime (35) is effective against community-acquired pneumonia in which ampicillin-resistant Haemophilus influence is the probable etiologic agent. Cefoxitin (23) is used to treat mixed aerobic—anaerobic infections including pelvic infections, intra-abdorninal infections, and nosocomial aspiration pneumonia. Cefonicid (31), because of its long half-life has been used in a once-a-day regimen to treat a variety of mild to moderate infections including community-acquired pneumonias, urinary tract infections, and infections of the skin and soft tissue (132,215). 

---