Plasma emission

Since boron produces weak flame absorption signals, an echelle spectrometer equipped with a d-c plasma excitation source similar to that procurable from Spectrametrics, Inc., 204 Andover Street, Andover, Massachusetts-01810, can be used to determine this element by AES. 

---

Schematic diagram of an argon plasma emission spectrometer.

Elemental Analysis Atomic absorption spectrometry X-Ray fluorescence spectrometry Plasma emission spectrometry... 

Choice of Atomization and Excitation Source Except for the alkali metals, detection limits when using an ICP are significantly better than those obtained with flame emission (Table 10.14). Plasmas also are subject to fewer spectral and chemical interferences. For these reasons a plasma emission source is usually the better choice. 

Accuracy When spectral and chemical interferences are insignificant, atomic emission is capable of producing quantitative results with accuracies of 1-5%. Accuracy in flame emission frequently is limited by chemical interferences. Because the higher temperature of a plasma source gives rise to more emission lines, accuracy when using plasma emission often is limited by stray radiation from overlapping emission lines. 

Precision For samples and standards in which the concentration of analyte exceeds the detection limit by at least a factor of 50, the relative standard deviation for both flame and plasma emission is about 1-5%. Perhaps the most important factor affecting precision is the stability of the flame s or plasma s temperature. For example, in a 2500 K flame a temperature fluctuation of +2.5 K gives a relative standard deviation of 1% in emission intensity. Significant improvements in precision may be realized when using internal standards. 

Sensitivity Sensitivity in flame atomic emission is strongly influenced by the temperature of the excitation source and the composition of the sample matrix. Normally, sensitivity is optimized by aspirating a standard solution and adjusting the flame s composition and the height from which emission is monitored until the emission intensity is maximized. Chemical interferences, when present, decrease the sensitivity of the analysis. With plasma emission, sensitivity is less influenced by the sample matrix. In some cases, for example, a plasma calibration curve prepared using standards in a matrix of distilled water can be used for samples with more complex matrices. 

Analyses of alloys or ores for hafnium by plasma emission atomic absorption spectroscopy, optical emission spectroscopy (qv), mass spectrometry (qv), x-ray spectroscopy (see X-ray technology), and neutron activation are possible without prior separation of hafnium (19). Alternatively, the combined hafnium and zirconium content can be separated from the sample by fusing the sample with sodium hydroxide, separating silica if present, and precipitating with mandelic acid from a dilute hydrochloric acid solution (20). The precipitate is ignited to oxide which is analy2ed by x-ray or emission spectroscopy to determine the relative proportion of each oxide. 

Small concentrations of iron can also be deterrnined by flame atomic absorption and inductively coupled plasma emission spectroscopies (see... 

J. Eialey, Elemental Mnalysis byMrgon Plasma Emission Spectroscopy, Teledyne Wab Chang Corp., Albany, Oieg., 1988. 

Fig. 4. Examples of emission spectrometry as a diagnostic monitoring tool for plasma processing, (a) The removal of chlorine contamination from copper diode leads using a hydrogen—nitrogen plasma. Emissions are added together from several wavelengths, (b) The etching and eventual removal of a 50-p.m thick polyimide layer from an aluminum substrate, where (x ) and (° ) correspond to wavelengths (519.82 and 561.02 nm, respectively) for molecular CO2...

Aluminum is best detected quaUtatively by optical emission spectroscopy. SoHds can be vaporized direcdy in a d-c arc and solutions can be dried on a carbon electrode. Alternatively, aluminum can be detected by plasma emission spectroscopy using an inductively coupled argon plasma or a d-c plasma. Atomic absorption using an aluminum hoUow cathode lamp is also an unambiguous and sensitive quaUtative method for determining alurninum. 

Quantitative aluminum deterrninations in aluminum and aluminum base alloys is rarely done. The aluminum content is generally inferred as the balance after determining alloying additions and tramp elements. When aluminum is present as an alloying component in alternative alloy systems it is commonly deterrnined by some form of spectroscopy (qv) spark source emission, x-ray fluorescence, plasma emission (both inductively coupled and d-c plasmas), or atomic absorption using a nitrous oxide acetylene flame. 

In addition to the spark emission methods, quantitative analysis directly on soHds can be accompHshed using x-ray fluorescence, or, after sample dissolution, accurate analyses can be made using plasma emission or atomic absorption spectroscopy (37). 

The sodium hydroxide is titrated with HCl. In a thermometric titration (92), the sibcate solution is treated first with hydrochloric acid to measure Na20 and then with hydrofluoric acid to determine precipitated Si02. Lower sibca concentrations are measured with the sibcomolybdate colorimetric method or instmmental techniques. X-ray fluorescence, atomic absorption and plasma emission spectroscopies, ion-selective electrodes, and ion chromatography are utilized to detect principal components as weU as trace cationic and anionic impurities. Eourier transform infrared, ft-nmr, laser Raman, and x-ray... 

P. W. J. M. Boumans, ed.. Inductively Coupled Plasma Emission Spectroscopy, 2 Vols. ( Methodology, Instrumentation, and Peformance Applications and Eundamentals),]oVn. Wiley Sons, Inc., New York, 1987. 

Atomic Absorption/Emission Spectrometry. Atomic absorption or emission spectrometric methods are commonly used for inorganic elements in a variety of matrices. The general principles and appHcations have been reviewed (43). Flame-emission spectrometry allows detection at low levels (10 g). It has been claimed that flame methods give better reproducibiHty than electrical excitation methods, owing to better control of several variables involved in flame excitation. Detection limits for selected elements by flame-emission spectrometry given in Table 4. Inductively coupled plasma emission spectrometry may also be employed. 

R. M. Brines, Application of Plasma Emission Spectrochemistry, Heyden Sons, Inc., Philadelphia, Pa., 1979. 

Inductively coupled argon plasma (icp) and direct current argon plasma (dcp) atomic emission spectrometry are solution techniques that have been appHed to copper-beryUium, nickel—beryUium, and aluminum—beryUium aUoys, beryUium compounds, and process solutions. The internal reference method, essential in spark source emission spectrometry, is also useful in minimizing drift in plasma emission spectrometry (17). Electrothermal (graphite... 

The commercial ores, beryl and bertrandite, are usually decomposed by fusion using sodium carbonate. The melt is dissolved in a mixture of sulfuric and hydrofluoric acids and the solution is evaporated to strong fumes to drive off siUcon tetrafluoride, diluted, then analy2ed by atomic absorption or plasma emission spectrometry. If sodium or siUcon are also to be determined, the ore may be fused with a mixture of lithium metaborate and lithium tetraborate, and the melt dissolved in nitric and hydrofluoric acids (17). 

MetaUic impurities in beryUium metal were formerly determined by d-c arc emission spectrography, foUowing dissolution of the sample in sulfuric acid and calcination to the oxide (16) and this technique is stUl used to determine less common trace elements in nuclear-grade beryUium. However, the common metallic impurities are more conveniently and accurately determined by d-c plasma emission spectrometry, foUowing dissolution of the sample in a hydrochloric—nitric—hydrofluoric acid mixture. Thermal neutron activation analysis has been used to complement d-c plasma and d-c arc emission spectrometry in the analysis of nuclear-grade beryUium. 

In the direct insertion technique, the sample (liquid or powder) is inserted into the plasma in a graphite, tantalum, or tungsten probe. If the sample is a liquid, the probe is raised to a location just below the bottom of the plasma, until it is dry. Then the probe is moved upward into the plasma. Emission intensities must be measured with time resolution because the signal is transient and its time dependence is element dependent, due to selective volatilization of the sample. The intensity-time behavior depends on the sample, probe material, and the shape and location of the probe. The main limitations of this technique are a time-dependent background and sample heterogeneity-limited precision. Currently, no commercial instruments using direct sample insertion are available, although both manual and h ly automated systems have been described. ... 

P. W. J. M. Boumans. Inductively Coupled Plasma Emission Spectroscopy,... 

Sulphate in Waters, Effluents and Solids (2nd Edition) [including Sulphate in Waters, Effluents and Some Solids by Barium Sulphate Gravimetry, Sulphate in waters and effluents by direct Barium Titrimetry, Sulphate in waters by Inductively Coupled Plasma Emission Spectrometry, Sulphate in waters and effluents by a Continuous Elow Indirect Spectrophotometric Method Using 2-Aminoperimidine, Sulphate in waters by Elow Injection Analysis Using a Turbidimetric Method, Sulphate in waters by Ion Chromatography, Sulphate in waters by Air-Segmented Continuous Elow Colorimetry using Methylthymol Blue], 1988... 

There are two basic types of instrument used in plasma emission analysis, namely the simultaneous and the sequential multi-element spectrometer. 

Analyses (dry basis) by inductively coupled plasma emission. 

HPLC-QFAAS is also problematical. Most development of atomic plasma emission in HPLC detection has been with the ICP and to some extent the DCP, in contrast with the dominance of the microwave-induced plasmas as element-selective GC detectors. An integrated GC-MIP system has been introduced commercially. Significant polymer/additive analysis applications are not abundant for GC and SFC hyphenations. Wider adoption of plasma spectral chromatographic detection for trace analysis and elemental speciation will depend on the introduction of standardised commercial instrumentation to permit interlaboratory comparison of data and the development of standard methods of analysis which can be widely used. 

Gas and liquid chromatography directly coupled with atomic spectrometry have been reviewed [178,179], as well as the determination of trace elements by chromatographic methods employing atomic plasma emission spectrometric detection [180]. Sutton et al. [181] have reviewed the use and applications of ICP-MS as a chromatographic and capillary electrophoretic detector, whereas Niessen [182] has briefly reviewed the applications of mass spectrometry to hyphenated techniques. 

---