Tank reactors

Stirred-tank reactors. Stirred-tank reactors consist simply of an... 

Stirred-tank reactors can be operated in batch, semi-batch, or... 

In fact, it is often possible with stirred-tank reactors to come close to the idealized well-stirred model in practice, providing the fluid phase is not too viscous. Such reactors should be avoided for some types of parallel reaction systems (see Fig. 2.2) and for all systems in which byproduct formation is via series reactions. 

Heat can be added to or removed from stirred-tank reactors via... 

Polymer is separated from the polymerisation slurry and slurried with acetic anhydride and sodium acetate catalyst. Acetylation of polymer end groups is carried out in a series of stirred tank reactors at temperatures up to 140°C. End-capped polymer is separated by filtration and washed at least twice, once with acetone and then with water. Polymer is made ready for extmsion compounding and other finishing steps by drying in a steam-tube drier. 

The emulsion process can be modified for the continuous production of latex. One such process (68) uses two stirred-tank reactors in series, followed by insulated hold-tanks. During continuous operation, 60% of the monomers are continuously charged to the first reactor with the remainder going into the second reactor. Surfactant is added only to the first reactor. The residence time is 2.5 h for the first reactor where the temperature is maintained at 65°C for 92% conversion. The second reactor is held at 68°C for a residence time of 2 h and conversion of 95%. 

Reaction conditions depend on the composition of the bauxite ore, and particularly on whether it contains primarily gibbsite, Al(OH)2, or boehmite [1318-23-6] AlOOH. The dissolution process is conducted in large, stirred vessels or alternatively in a tubular reactor. The process originated as a batch process, but has been converted to a continuous one, using a series of stirred tank reactors or a tubular reactor. 

Wet Oxidation Reactor Design. Several types of reactor designs have been employed for wet oxidation processes. Zimpro, the largest manufacturer of wet oxidation systems, typically uses a tower reactor system. The reactor is a bubble tower where air is introduced at the bottom to achieve plug flow with controlled back-mixing. Residence time is typically under one hour. A horizontal, stirred tank reactor system, known as the Wetox process, was initially developed by Barber-Cohnan, and is also offered by Zimpro. 

Some slurry processes use continuous stirred tank reactors and relatively heavy solvents (57) these ate employed by such companies as Hoechst, Montedison, Mitsubishi, Dow, and Nissan. In the Hoechst process (Eig. 4), hexane is used as the diluent. Reactors usually operate at 80—90°C and a total pressure of 1—3 MPa (10—30 psi). The solvent, ethylene, catalyst components, and hydrogen are all continuously fed into the reactor. The residence time of catalyst particles in the reactor is two to three hours. The polymer slurry may be transferred into a smaller reactor for post-polymerization. In most cases, molecular weight of polymer is controlled by the addition of hydrogen to both reactors. After the slurry exits the second reactor, the total charge is separated by a centrifuge into a Hquid stream and soHd polymer. The solvent is then steam-stripped from wet polymer, purified, and returned to the main reactor the wet polymer is dried and pelletized. Variations of this process are widely used throughout the world. 

Third-generation high yield supported catalysts are also used in processes in which Hquid monomer is polymerized in continuous stirred tank reactors. The Hypol process (Mitsui Petrochemical), utilizes the same supported catalyst technology as the Spheripol process (133). Rexene has converted the hquid monomer process to the newer high yield catalysts. Shell uses its high yield (SHAC) catalysts to produce homopolymers and random copolymers in the Lippshac process (130). 

Fig. 5. Hoechst/Rhc ne-Poulenc oxo flow scheme A, stirred tank reactor B, separator C, phase separator D, stripping column E, heat exchanger and F,...

Processes. Toluene is nitrated ia two stages. Mononitration occurs ia mixed acid, 30% HNO and 55% H2SO4, at 30—70°C ia a series of continuous stirred-tank reactors. Heat is Hberated and must be removed. The isomer distribution is approximately 58% o-nitrotoluene 38% -nitrotoluene, and 4% y -nitrotoluene (Fig. 1). 

A process based on a nickel catalyst, either supported or Raney type, is described ia Olin Mathieson patents (26,27). The reduction is carried out ia a continuous stirred tank reactor with a concentric filter element built iato the reactor so that the catalyst remains ia the reaction 2one. Methanol is used as a solvent. Reaction conditions are 2.4—3.5 MPa (350—500 psi), 120—140°C. Keeping the catalyst iaside the reactor iacreases catalyst lifetime by maintaining a hydrogen atmosphere on its surface at all times and minimises handling losses. Periodic cleaning of the filter element is required. 

Specific reactor characteristics depend on the particular use of the reactor as a laboratory, pilot plant, or industrial unit. AH reactors have in common selected characteristics of four basic reactor types the weH-stirred batch reactor, the semibatch reactor, the continuous-flow stirred-tank reactor, and the tubular reactor (Fig. 1). A reactor may be represented by or modeled after one or a combination of these. SuitabHity of a model depends on the extent to which the impacts of the reactions, and thermal and transport processes, are predicted for conditions outside of the database used in developing the model (1-4). 

Continuous-Flow Stirred-Tank Reactor. In a continuous-flow stirred-tank reactor (CSTR), reactants and products are continuously added and withdrawn. In practice, mechanical or hydrauHc agitation is required to achieve uniform composition and temperature, a choice strongly influenced by process considerations, ie, multiple specialty product requirements and mechanical seal pressure limitations. The CSTR is the idealized opposite of the weU-stirred batch and tubular plug-flow reactors. Analysis of selected combinations of these reactor types can be useful in quantitatively evaluating more complex gas-, Hquid-, and soHd-flow behaviors. 

Continuous-flow stirred-tank reactors ia series are simpler and easier to design for isothermal operation than are tubular reactors. Reactions with narrow operating temperature ranges or those requiring close control of reactant concentrations for optimum selectivity benefit from series arrangements. 

Continuous-Flow Stirred-Tank Reactors. The synthesis of j )-tolualdehyde from toluene and carbon monoxide has been carried out using CSTR equipment (81). -Tolualdehyde (PTAL) is an intermediate in the manufacture of terephthabc acid. Hydrogen fluoride—boron trifluoride catalyzes the carbonylation of toluene to PTAL. In the industrial process, separate stirred tanks are used for each process step. Toluene and recycle HF and BF ... 

Copolymers are typically manufactured using weU-mixed continuous-stirred tank reactor (cstr) processes, where the lack of composition drift does not cause loss of transparency. SAN copolymers prepared in batch or continuous plug-flow processes, on the other hand, are typically hazy on account of composition drift. SAN copolymers with as Httle as 4% by wt difference in acrylonitrile composition are immiscible (44). SAN is extremely incompatible with PS as Httle as 50 ppm of PS contamination in SAN causes haze. Copolymers with over 30 wt % acrylonitrile are available and have good barrier properties. If the acrylonitrile content of the copolymer is increased to >40 wt %, the copolymer becomes ductile. These copolymers also constitute the rigid matrix phase of the ABS engineering plastics. 

In the slurry process, the hydrolysis is accompHshed using two stirred-tank reactors in series (266). Solutions of poly(vinyl acetate) and catalyst are continuously added to the first reactor, where 90% of the conversion occur, and then transferred to the second reactor to reach hiU conversion. Alkyl acetate and alcohols are continuously distilled off in order to drive the equiUbrium of the reaction. The resulting poly(vinyl alcohol) particles tend to be very fine, resulting in a dusty product. The process has been modified to yield a less dusty product through process changes (267,268) and the use of additives (269). Partially hydroly2ed products having a narrow hydrolysis distribution cannot be prepared by this method. 

Cooking extmders have been studied for the Uquefaction of starch, but the high temperature inactivation of the enzymes in the extmder demands doses 5—10 times higher than under conditions in a jet cooker (69). Eor example, continuous nonpressure cooking of wheat for the production of ethanol is carried out at 85°C in two continuous stirred tank reactors (CSTR) connected in series plug-fiow tube reactors may be included if only one CSTR is used (70). 

Despite the higher cost compared with ordinary catalysts, such as sulfuric or hydrochloric acid, the cation exchangers present several features that make their use economical. The abiHty to use these agents in a fixed-bed reactor operation makes them attractive for a continuous process (50,51). Cation-exchange catalysts can be used also in continuous stirred tank reactor (CSTR) operation. 

Over 25 years ago the coking factor of the radiant coil was empirically correlated to operating conditions (48). It has been assumed that the mass transfer of coke precursors from the bulk of the gas to the walls was controlling the rate of deposition (39). Kinetic models (24,49,50) were developed based on the chemical reaction at the wall as a controlling step. Bench-scale data (51—53) appear to indicate that a chemical reaction controls. However, flow regimes of bench-scale reactors are so different from the commercial furnaces that scale-up of bench-scale results caimot be confidently appHed to commercial furnaces. For example. Figure 3 shows the coke deposited on a controlled cylindrical specimen in a continuous stirred tank reactor (CSTR) and the rate of coke deposition. The deposition rate decreases with time and attains a pseudo steady value. Though this is achieved in a matter of rninutes in bench-scale reactors, it takes a few days in a commercial furnace. 

A differential equation for a function that depends on only one variable, often time, is called an ordinary differential equation. The general solution to the differential equation includes many possibilities the boundaiy or initial conditions are needed to specify which of those are desired. If all conditions are at one point, then the problem is an initial valueproblem and can be integrated from that point on. If some of the conditions are available at one point and others at another point, then the ordinaiy differential equations become two-point boundaiy value problems, which are treated in the next section. Initial value problems as ordinary differential equations arise in control of lumped parameter models, transient models of stirred tank reactors, and in all models where there are no spatial gradients in the unknowns. 

R Gas huhhle swarm in sparged stirred tank reactor with solids present... 

---