Reactor types stirred tank

Reactor types Stirred tank or tower, bubbling reactor RPB... 

A useful classification of lands of reaclors is in terms of their concentration distributions. The concentration profiles of certain limiting cases are illustrated in Fig. 7-3 namely, of batch reactors, continuously stirred tanks, and tubular flow reactors. Basic types of flow reactors are illustrated in Fig. 7-4. Many others, employing granular catalysts and for multiphase reactions, are illustratea throughout Sec. 23. The present material deals with the sizes, performances and heat effects of these ideal types. They afford standards of comparison. 

Laboratory reactor for studying three-phase processes can be divided in reactors with mobile and immobile catalyst particles. Bubble (suspension) column reactors, mechanically stirred tank reactors, ebullated-bed reactors and gas-lift reactors belong the class of reactors with mobile catalyst particles. Fixed-bed reactors with cocurrent (trickle-bed reactor and bubble columns, see Figs. 5.4-7 and 5.4-8 in Section 5.4.1) or countercurrent (packed column, see Fig. 5.4-8) flow of phases are reactors with immobile catalyst particles. A mobile catalyst is usually of the form of finely powdered particles, while coarser catalysts are studied when placing them in a fixed place (possibly moving as in mechanically agitated basket-type reactors). 

Starch Liquefaction. Starch in its natural state is only degraded slowly by CC-amylases. To make the starch susceptible to enzymatic breakdown, it is necessary to gelatinize and liquefy a slurry with a 30—40% dry matter content. Gelatinization temperature depends on the type of starch (67) com is the most common source of industrial starches followed by wheat, tapioca, and potatoes. Liquefaction is achieved by adding a heat-stable a-amylase to the starch slurry. The equipment used for liquefaction may be stirred tank reactors, continuous stirred tank reactors (CSTR), or a jet cooker. Most starch processing plants liquefy the starch with a single enzyme dose in a process using a jet cooker (Fig. 9). 

Homogeneous catalytic reactions are usually carried out in either a stirred tank or a tubular reactor. As can be seen from Table 3.1, tubular reactors may be of different types. Stirred tank reactors offer a very high degree of back mixing, while tubular reactors lead to plug flow conditions. The concentration of the reactants are uniform throughout the vessel in the case of stirred tank reactor,... 

FIG. 7-4 Types of flow reactors (a) stirred tank battery, (b) vertically staged, (c) compartmented, (d) single-jacketed tube, (e) shell and tube, (/) semiflow stirred tank. 

Reflecting the importance of continuous emulsion polymerization processes, numerous investigations have been carried out to date, which are categorized into three groups (1) studies on the reactor configuration (stirred-tank reactors, tubular type reactors such as a simple tubular reactors, pulsed tubular reactors... 

In this chapter, the theories for gas absorption plus reaction are presented first for relatively slow reactions and then for fast reactions and for instantaneous reactions. Performance data and scaleup criteria for several types of gas-liquid reactors are then reviewed. For a given reaction, the intrinsic kinetics of the liquid-phase reaction are the same for all types of reactors, including stirred tanks, packed columns, bubble columns, and spray contactors, but the mass transfer coeffieients differ greatly, and the... 

When carrying out a gas-liquid reaction, the gas may be dispersed in the liquid, as in bubble-column reactors or stirred tanks, or the gas phase may be continuous, as in spray contactors or trickle-bed reactors. The fundamental kinetics are independent of the reactor type, but the reaction rate per unit volume and the selectivity may differ because of differences in surface area, mass transfer coefficient, and extent of mixing. In the following sections, gas holdup and mass transfer correlations and other performance data for gas liquid reactors are reviewed and some problems of scaleup are discussed. 

There are two common types of continuous reactors continuous stirred tank reactors (CSTRs) (53), and plug flow reactors (PFRs). CSTRs are simply large tanks that are ideally well-mixed (such that the emulsion composition is uniform throughout the entire reactor volume) in which the polymerisation takes place. CSTRs are operated at a constant overall conversion. CSTRs are often used in series or trains to build up conversion incrementally. Styrene-butadiene rubber has been produced in this manner. Not all latex particles spend the same amount of time polymerising in a CSTR. Some particles exit sooner than others, producing a distribution of particle residence times, diameters and compositions. 

In this chapter, and on the DVD-ROM, we ve introduced each of the major types of industrial reactors batch, stirred tank, tubular, and fixed bed (packed bed). Many variations and modifications of these commercial reactors (e.g., semibatch, fluidized bed) are in current use for further elaboratiem. refer to the detailed discussion of industrial reactors given by Walas. ... 

Most chemical processes involve two important operations (reaction and separalion) that are typically carried out in different sections of the plant and use different equipment. The reaction section of the process can use several types of reactors [continuous stirred-tank reactor (CSTR), tubular, or batch] and operate under a wide variety of conditions (catalyzed, adiabatic, cooled or heated, single phase, multiple phases, etc.). The separation section can have several types of operations (distillation, extraction, crystallization, adsorption, etc.), with distillation being by far the most commonly used method. Recycle streams between the two sections of these conventional multiunit flowsheets are often incorporated in the process for a variety of reasons to improve conversion and yield, to minimize the production of undesirable byproducts, to improve energy efficiency, and to improve dynamic controllability. 

In fact, it is often possible with stirred-tank reactors to come close to the idealized well-stirred model in practice, providing the fluid phase is not too viscous. Such reactors should be avoided for some types of parallel reaction systems (see Fig. 2.2) and for all systems in which byproduct formation is via series reactions. 

Wet Oxidation Reactor Design. Several types of reactor designs have been employed for wet oxidation processes. Zimpro, the largest manufacturer of wet oxidation systems, typically uses a tower reactor system. The reactor is a bubble tower where air is introduced at the bottom to achieve plug flow with controlled back-mixing. Residence time is typically under one hour. A horizontal, stirred tank reactor system, known as the Wetox process, was initially developed by Barber-Cohnan, and is also offered by Zimpro. 

Classification of the many different encapsulation processes is usehil. Previous schemes employing the categories chemical or physical are unsatisfactory because many so-called chemical processes involve exclusively physical phenomena, whereas so-called physical processes can utilize chemical phenomena. An alternative approach is to classify all encapsulation processes as either Type A or Type B processes. Type A processes are defined as those in which capsule formation occurs entirely in a Hquid-filled stirred tank or tubular reactor. Emulsion and dispersion stabiUty play a key role in determining the success of such processes. Type B processes are processes in which capsule formation occurs because a coating is sprayed or deposited in some manner onto the surface of a Hquid or soHd core material dispersed in a gas phase or vacuum. This category also includes processes in which Hquid droplets containing core material are sprayed into a gas phase and subsequentiy solidified to produce microcapsules. Emulsion and dispersion stabilization can play a key role in the success of Type B processes also. 

A process based on a nickel catalyst, either supported or Raney type, is described ia Olin Mathieson patents (26,27). The reduction is carried out ia a continuous stirred tank reactor with a concentric filter element built iato the reactor so that the catalyst remains ia the reaction 2one. Methanol is used as a solvent. Reaction conditions are 2.4—3.5 MPa (350—500 psi), 120—140°C. Keeping the catalyst iaside the reactor iacreases catalyst lifetime by maintaining a hydrogen atmosphere on its surface at all times and minimises handling losses. Periodic cleaning of the filter element is required. 

Specific reactor characteristics depend on the particular use of the reactor as a laboratory, pilot plant, or industrial unit. AH reactors have in common selected characteristics of four basic reactor types the weH-stirred batch reactor, the semibatch reactor, the continuous-flow stirred-tank reactor, and the tubular reactor (Fig. 1). A reactor may be represented by or modeled after one or a combination of these. SuitabHity of a model depends on the extent to which the impacts of the reactions, and thermal and transport processes, are predicted for conditions outside of the database used in developing the model (1-4). 

Continuous-Flow Stirred-Tank Reactor. In a continuous-flow stirred-tank reactor (CSTR), reactants and products are continuously added and withdrawn. In practice, mechanical or hydrauHc agitation is required to achieve uniform composition and temperature, a choice strongly influenced by process considerations, ie, multiple specialty product requirements and mechanical seal pressure limitations. The CSTR is the idealized opposite of the weU-stirred batch and tubular plug-flow reactors. Analysis of selected combinations of these reactor types can be useful in quantitatively evaluating more complex gas-, Hquid-, and soHd-flow behaviors. 

---