Molecular weight Acrylate copolymers

The Tgs of the copolymers increase systematically as the level of VEC increases. As in the case of copolymers with butyl acrylate the molecular weights also decreases with increasing levels of VEC- However, unlike with the butyl acrylate copolymers, the molecular weight appears to be reaching a limiting value as the VEC content increases (Figure 4). Again, more detailed analysis of the copolymers are required to fully understand these effects. 

Miscibility of polymer blends is relatively rare, and is usually limited to a narrow range of independent variables, such as composition of a copolymer, molecular weight, temperature, pressure, and so on [185]. The miscible blends are mainly of academic interest - the information obtained is useful for designing compatibilizers. Exceptions are blends of poly(vinylidene fluoride) (PVDF) with acrylic or polyimide (e.g., PMMA), which are characterized by outstanding UV stability and are used for... 

Styrenes, acrylics High molecular weight acrylic copolymers improve processability of PVC compounds, good weatherability lubricant grades reduce adherence of melt to processing equipment... 

The product mix of autoclave and tubular reactors are similar in terms of LDPE homopolymers (0.910-0.935 g/cc) and some specialty grades of polyethylene such as ethylene/vinyl acetate copolymers up to about 30 wt% vinyl acetate (VA). However, the autoclave process provides higher levels of vinyl acetate (40 wt%) in ethylene/VA copolymers and additional specialty grades of polyethylene such as ethylene/methyl acrylate, ethylene/acrylic acid and ethylene/n-butyl acrylate. Polyethylene molecular weight can be varied over a wide range with the high-pressure process, with Melt Index values (I ranging from 0.15 to 40. 

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

The most common VI improvers are methacrylate polymers and copolymers, acrylate polymers (see Acrylic ester polymers), olefin polymers and copolymers, and styrene—butadiene copolymers. The degree of VI improvement from these materials is a function of the molecular weight distribution of the polymer. VI improvers are used in engine oils, automatic transmission fluids, multipurpose tractor fluids, hydrautic fluids, and gear lubricants. Their use permits the formulation of products that provide satisfactory lubrication over a much wider temperature range than is possible using mineral oils alone. 

Ionomer resins consisting of ethylene—methacrylic acid copolymers partially neutralized with sodium or zinc were commercially introduced in 1964 by Du Pont under the Sudyn trademark (1). More recently, a similar line of products, sold as Hi-Mdan resins, has been commercialized by Mitsui—Du Pont in Japan. lolon ionomeric resins, based on ethylene—acrylic acid, are produced by Exxon in Belgium. Ionomers containing about 1 mol % of carboxylate groups are offered by BP in Europe as Novex resins. Low molecular weight, waxy Aclyn ionomers are produced and sold by AHiedSignal. 

Polymerization of methacrylates is also possible via what is known as group-transfer polymerization. Although only limited commercial use has been made of this technique, it does provide a route to block copolymers that is not available from ordinary free-radical polymerizations. In a prototypical group-transfer polymerization the fluoride-ion-catalyzed reaction of a methacrylate (or acrylate) in the presence of a silyl ketene acetal gives a high molecular weight polymer (45—50). 

Intrinsic viscosity—molecular weight relationships have been obtained for copolymers in methyl ethyl ketone. The value for a 15 wt % ethyl acrylate (EA) copolymer is [77] = 2.88 x 10 . ... 

The most effective and widely used dispersants are low molecular weight anionic polymers. Dispersion technology has advanced to the point at which polymers are designed for specific classes of foulants or for a broad spectmm of materials. Acrylate-based polymers are widely used as dispersants. They have advanced from simple homopolymers of acryflc acid to more advanced copolymers and terpolymers. The performance characteristics of the acrylate polymers are a function of their molecular weight and stmcture, along with the types of monomeric units incorporated into the polymer backbone. 

Low molecular weight liquid nitrile rubbers with vinyl, carboxyl or mercaptan reactive end groups have been used with acrylic adhesives, epoxide resins and polyesters. Japanese workers have produced interesting butadiene-acrylonitrile alternating copolymers using Ziegler-Natta-type catalysts that are capable of some degree of ciystallisation. 

Among the different pressure sensitive adhesives, acrylates are unique because they are one of the few materials that can be synthesized to be inherently tacky. Indeed, polyvinylethers, some amorphous polyolefins, and some ethylene-vinyl acetate copolymers are the only other polymers that share this unique property. Because of the access to a wide range of commercial monomers, their relatively low cost, and their ease of polymerization, acrylates have become the dominant single component pressure sensitive adhesive materials used in the industry. Other PSAs, such as those based on natural rubber or synthetic block copolymers with rubbery midblock require compounding of the elastomer with low molecular weight additives such as tackifiers, oils, and/or plasticizers. The absence of these low molecular weight additives can have some desirable advantages, such as ... 

Specialty waxes include polar waxes for more polar adhesive systems. Examples would be castor wax (triglyceride of 12-hydroxy stearic acid) or Paracin wax N- 2 hydroxy ethyl)-12-hydroxy stearamide) which are used in polyester, polyamide, or with high VA EVA copolymer-based systems. Other common polar waxes are maleated polyethylenes, which are used to improve the specific adhesion of polyethylene-based adhesives, and low molecular weight ethylene copolymers with vinyl acetate or acrylic acid, which are used to improve low temperature adhesion. High melting point isotactic polypropylene wax (7 155°C) and highly refined paraffin wax (7,n 83°C) are used where maximum heat resistance is critical. Needless to say, these specialty waxes also command a premium price, ranging from 2 to 5 times that of conventional paraffin wax. 

Standard-grade PSAs are usually made from styrene-butadiene rubber (SBR), natural rubber, or blends thereof in solution. In addition to rubbers, polyacrylates, polymethylacrylates, polyfvinyl ethers), polychloroprene, and polyisobutenes are often components of the system ([198], pp. 25-39). These are often modified with phenolic resins, or resins based on rosin esters, coumarones, or hydrocarbons. Phenolic resins improve temperature resistance, solvent resistance, and cohesive strength of PSA ([196], pp. 276-278). Antioxidants and tackifiers are also essential components. Sometimes the tackifier will be a lower molecular weight component of the high polymer system. The phenolic resins may be standard resoles, alkyl phenolics, or terpene-phenolic systems ([198], pp. 25-39 and 80-81). Pressure-sensitive dispersions are normally comprised of special acrylic ester copolymers with resin modifiers. The high polymer base used determines adhesive and cohesive properties of the PSA. 

Thomas et al. [64] prepared copolymers of 1-pyreneacrylic acid with acrylic acid (AA), 17, and with methacrylic acid (MA), 18, incorporating not more than one pyrene unit per polymer chain. The mole ratios of pyrene to AA and MA units were 1150 and 1390, respectively. The molecular weights of 17 and 18 were 8.3 x lO4... 

Chung and coworkers have reported on the use of stable borinale or boroxyl radicals (e.g. 114) to mediate radical polymerization." Methacrylates (MMA) and acrylates (trifluoroelhyl acrylate) have been polymerized at ambient temperature to yield polymers with relatively narrow molecular weight distributions.231233 The method has been used to prepare block copolymers and polyolefin graft copolymers.2 4 37... 

ATRP has also been used to synthesize maeromononicrs subsequently used to make graft copolymers by conventional radical polymerization. Thus, low molecular weight PBA formed by ATRP was converted in near quantitative yield to the methacrylate ester (351) or the corresponding acrylate ester.612... 

---