Ethylene propylene-diene monomer

At this point in the process, thermoplastic and chlorosulfonated polyethylene (CSPE) membranes are complete and are ready for packaging. In the case of ethylene—propylene—diene monomer (EPDM), the curing step occurs before the membrane is ready for packaging. The curing process is accomphshed by placing the membrane in a large vulcanizer where the material is heated under pressure to complete the cure. 

Fig. 1. SAE J200 Classification system for ASTM No. 3 oil where in volume swell nr = no requirement. EPDM is ethylene—propylene—diene monomer HR, butyl mbber SBR, styrene—butadiene mbber NR, natural mbber VMQ, methyl vinyl siUcone CR, chloroprene FKM, fluoroelastomer FVMQ, fluorovinyl methyl siUcone ACM, acryUc elastomers HSN, hydrogenated nitrile ECO, epichlorohydrin and NBR, nitrile mbber.

Ethylene—Propylene Rubber. Ethylene and propjiene copolymerize to produce a wide range of elastomeric and thermoplastic products. Often a third monomer such dicyclopentadiene, hexadiene, or ethylene norbomene is incorporated at 2—12% into the polymer backbone and leads to the designation ethylene—propylene—diene monomer (EPDM) mbber (see Elastomers, synthetic-ethylene-propylene-diene rubber). The third monomer introduces sites of unsaturation that allow vulcanization by conventional sulfur cures. At high levels of third monomer it is possible to achieve cure rates that are equivalent to conventional mbbers such as SBR and PBD. Ethylene—propylene mbber (EPR) requires peroxide vulcanization. 

In consequence ethylene-propylene rubbers were introduced with a small amount (3-8%) of a third, diene, monomer which provided a cross-link site for accelerated sulphur vulcanisation. Such ethylene-propylene-diene monomer ternary copolymers are designated as EPDM rubbers. 

EPDM (Ethylene Propylene Diene Monomer Rubbers) 320 Steam, High-temperature Aqueous Solutions, Inorganic Acids and Organic Acids or bases... 

Process systems handling polymers and resins (e.g., butyl rubber or ethylene-propylene diene monomer rubbers) are often subject to plugging at dead-end locations such as PR valve inlets. In extreme cases, complete blockage of inlet piping and valve nozzle can result. This problem can be eliminated by the application of a flush-seated PR valve, in which dead-end areas are eliminated by placing the valve disc flush with the vessel wall, in the flow pattern of the contents. 

TPEs from blends of rubber and plastics constitute an important category of TPEs. These can be prepared either by the melt mixing of plastics and rubbers in an internal mixer or by solvent casting from a suitable solvent. The commonly used plastics and rubbers include polypropylene (PP), polyethylene (PE), polystyrene (PS), nylon, ethylene propylene diene monomer rubber (EPDM), natural rubber (NR), butyl rubber, nitrile rubber, etc. TPEs from blends of rubbers and plastics have certain typical advantages over the other TPEs. In this case, the required properties can easily be achieved by the proper selection of rubbers and plastics and by the proper change in their ratios. The overall performance of the resultant TPEs can be improved by changing the phase structure and crystallinity of plastics and also by the proper incorporation of suitable fillers, crosslinkers, and interfacial agents. 

ATBN - amine terminated nitrile rubber X - Flory Huggins interaction parameter CPE - carboxylated polyethylene d - width at half height of the copolymer profile given by Kuhn statistical segment length DMAE - dimethyl amino ethanol r - interfacial tension reduction d - particle size reduction DSC - differential scanning calorimetry EMA - ethylene methyl acrylate copolymer ENR - epoxidized natural rubber EOR - ethylene olefin rubber EPDM - ethylene propylene diene monomer EPM - ethylene propylene monomer rubber EPR - ethylene propylene rubber EPR-g-SA - succinic anhydride grafted ethylene propylene rubber... 

This is a nonpolar rubber with very little unsamration. Nanoclays as well as nanotubes have been used to prepare nanocomposites of ethylene-propylene-diene monomer (EPDM) rubber. The work mostly covers the preparation and characterization of these nanocomposites. Different processing conditions, morphology, and mechanical properties have been smdied [61-64]. Acharya et al. [61] have prepared and characterized the EPDM-based organo-nanoclay composites by X-ray diffracto-gram (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy... 

Ethylene-propylene-diene monomer rubber EPDM... 

FIGURE 11,1 Ultrasonic velocity versus acrylonitrile-butadiene mbber/ethylene-propylene-diene monomer (NBR-EPDM) blend composition (a) no compatibiUzer, (b) with chloro-sulfonated polyethylene (CSM), and (c) with chlorinated polyethylene (CM). (From Pandey, K.N., Setua, D.K., and Mathur, G.N., Polym. Eng. Set, 45, 1265, 2005.)... 

FIGURE 11.7 Inter-mbber bonding scheme for blending ethylene-propylene-diene monomer (EPDM) with nitrile mbber with a cross-linking agent. (From Naskar, M., Debnath, S.C., and Basu, D.K., Rubber Chem. TechnoL, 75, 309, 2002.)... 

In one of the first reports on fiber reinforcement of rubber, natural rubber (NR) was used by Collier [9] as the rubber matrix, which was reinforced using short cotton fibers. Some of the most commonly used rubber matrices for fiber reinforcement are NR, ethylene-propylene-diene monomer (EPDM) rubber, styrene-butadiene rubber (SBR), polychloroprene rubber, and nitrile rubber [10-13]. These rubbers were reinforced using short and long fibers including jute, silk, and rayon [14—16]. 

Mechanical Properties and Cure Rate Index of the Mixes—Role of Dry Bonding System on the Reinforcement of Ethylene-Propylene-Diene Monomer (EPDM) Rubber with Melamine Fiber ... 

FIGURE 12.7 Monsanto rheometric curves of ethylene-propylene-diene monomer (EPDM) rubber-melamine fiber composites [64]. A, gum compound B, compound containing 30 phr melamine fiber but no dry bonding system and C, compound containing both dry bonding system and 30 phr melamine fiber. (From Rajeev, R.S., Bhowmick, A.K., De, S.K., Kao, G.J.P., and Bandyopadhyay, S., Polym. Compos., 23, 574, 2002. With permission.)... 

FIGURE 12.10 Tapping mode atomic force microscopy (AFM) images of the section analyzes of ethylene-propylene-diene monomer (EPDM) rubber-melamine fiber composites. A, composite containing no dry bonding system B, composite containing resorcinol, hexamine, and silica in the concentrations 5, 3, and 15 phr, respectively. 

The accelerated sulfur vulcanization of general-purpose diene rubbers (e.g., NR, styrene-butadiene rubber [SBR], and butadiene rubber [BR]) by sulfur in the presence of organic accelerators and other rubbers, which are vulcanized by closely related technology (e.g., ethylene-propylene-diene monomer [EPDM] mbber, butyl rubber [HR], halobutyl mbber [XIIR], nitrile rubber [NBR]) comprises more than 90% of all vulcanizations. 

Cure Systems in Ethylene-Propylene Diene Monomer (EPDM)... 

The model describes the characteristic stress softening via the prestrain-dependent amplification factor X in Equation 22.22. It also considers the hysteresis behavior of reinforced mbbers, since the sum in Equation 22.23 has taken over the stretching directions with ds/dt > 0, only, implying that up and down cycles are described differently. An example showing a fit of various hysteresis cycles of silica-filled ethylene-propylene-diene monomer (EPDM) mbber in the medium-strain regime up to 50% is depicted in Figure 22.12. It must be noted that the topological constraint modulus Gg has... 

---