Systems, electrical

Process technicians are not trained as electrical technicians however, safely operating a system that uses electricity requires a comprehensive education. Only qualified electricians work on industrial electrical systems that can have very high voltages. Typically, two electricians work on 

---

In some cases particles have been added to electrical systems to improve heat removal, for example with an SF -fluidized particulate bed to be used in transformers (47). This process appears feasible, using polytetrafluoroethylene (PTFE) particles of low dielectric constant. For a successful appHcation, practical problems such as fluidizing narrow gaps must be solved. 

G. Luxa and co-workers. Item D. Paschen CurveforSF, 1975 CIGRE International Conference on Earge High Tension Electrical Systems. 

Induction furnaces utilize the phenomena of electromagnetic induction to produce an electric current in the load or workpiece. This current is a result of a varying magnetic field created by an alternating current in a cod that typically surrounds the workpiece. Power to heat the load results from the passage of the electric current through the resistance of the load. Physical contact between the electric system and the material to be heated is not essential and is usually avoided. Nonconducting materials cannot be heated directiy by induction fields. 

Solar cells have been used extensively and successfully to power sateUites in space since the late 1950s, where their high power-to-weight ratio and demonstrated rehabiUty are especially desirable characteristics. On earth, where electrical systems typically provide large amounts of power at reasonable costs, three principal technical limitations have thus far impeded the widespread use of photovoltaic products solar cells are expensive, sunlight has a relatively low power density, and commercially available solar cells convert sunlight to electricity with limited efficiency. Clearly, terrestrial solar cells must be reasonably efficient, affordable, and durable. International efforts are dedicated to obtaining such devices, and a number of these activities have been reviewed (1). 

An iajection mol ding machine is operated by hydrauHc power and equipped with an electric motor and hydrauHc pump. The maximum hydrauHc oil pressure is ca 14 MPa (2000 psi). A hydrauHc cylinder opens and closes the mold and holds the mold closed duriag iajection another cylinder forces the screw forward, thereby injecting the melt iato the mold. A separate hydrauHc motor turns the screw to plasticate, homogenize, and pressurize the melt. Control of these movements is a combined function of the hydrauHc and electrical systems (35—37). 

Bayer, USI, and DuPont are U.S. suppHers. There is an estimated 2300—4000 t/yr of EVA used in the United States. Uses include automotive electrical system components, eg, ignition cable, footwear, weatherstripping, and misceUaneous O-rings and seals for industrial appHcations. 

Dust-tight electrical systems should be used in areas where activated carbon is present, particularly powdered products (66). When partially wet activated carbon comes into contact with unprotected metal, galvanic currents can be set up these result in metal corrosion (67). 

In addition, the copper industry s market development activities have resulted in appHcations such as clad ship hulls, sheathing for offshore platforms, automotive electrical systems including electric vehicles, improved automobde radiators, solar energy, fire sprinkler systems, parts for fusion reactors, semiconductor lead frames, shape memory alloys, and superconducting ceramics (qv) containing copper oxides. 

Considerable effort has been directed to determining the causes of connection failutes and to learning how to minimize the likelihood of occurrence. Acceptable failute rates range from <1 in 10 operating hours for contacts in air-frame (31) electrical systems and in some telecommunications equipment, to 100—1000 in 10 operating hours in instmments, to even larger rates for contacts in many consumer products. A failute is defined as exceedance of contact resistance, which can be as Httle as twice the initial contact resistance, that causes circuit malfunction. The required lifetimes of connectors may be >20 yr, although most required appHcation times ate shorter (see Materials reliability). 

Electrical. The plant electrical system is sometimes more important than the steam system. The electrical system consists of the utihty company s entry substation, any ia-plant generating equipment, primary distribution feeders, secondary substations and transformers, final distribution cables, and various items of switch-gear, protective relays, motor starters, motors, lighting control panels, and capacitors to adjust power factor. 

For most plants, 01001 110 distribution systems start at the power company s service point on the plant s property. The choice of an electrical system will depend on many fartors relating to the particular projecl . A wide range of items, from switchgear, transformers, and motor control centers to cabling, earthing, and lighting, are required. Normally, competitive quotations would be obtained to take an estimate beyond the study stage. 

Electric Tracing An electric tracing system (see Fig. 10-178) consists of an electric heater placed against the pipe under the thermal insulation, the supply of electricity to the tracer, and any control or monitoring system that may be used (optional). The supply of electricity to the tracer usually consists of an electrical panel and electrical conduit or cable trays. Depending on the size or the tracing system and the capacity of the existing electrical system, an additional transformer may be required. 

Electrical-system characteristics if the recovered power is used to generate electricity... 

Specifications for intrinsically safe electrical system i General recommendations on the selection of the appropriate group of electrical apparatus based on safe gaps and minimum igniting currents 3682/1991 BS 5501-7/1977 BS 5501-9/1982 BS 5345-1/1989 ... 

Voltage ratings for a.c. electrical systems and equipment above 230 kV Insulation coordination, definitions, principles and rules... 

Miller. T.J.E., Reactive Power Control in Electric Systems. John Wiley. NewYork (1982). 

Rated short-time current rating this is the same as for the system to which it is connected, and as assigned to the associated switchgear (Section 13.4.1(5)). The effects of a short-circuit on an electrical system are discussed below. 

Theory of overvoltages Analysis of ungrounded and grounded systems The necessity of grounding an electrical system Analysis of a grounded system ... 

Schatz, R., Shooman, M. and Shaw, L. 1974 Application of Time Dependent Stress-Strength Models of Non-Electrical and Electrical Systems. In Proceedings Reliability and Maintainability Symposium, 540-547. 

Controls, instrumentation, and electrical systems in a gas turbine are defined. The outline in the standard is the minimum a user needs for safe... 

Grounded Y versus ungrounded delta electrical system... 

Semiconductor control modules gate the thyristors, which switch cm rent to the motor field at the optimum motor speed and precise phase angle. This assures synchronizing with minimum system disturbance. On pull-out, the discharge resistor is reapplied and excitation is removed k> provide protection to the rotor winding, shaft, and external electrical system. The control resynchronizes the motor after the cause of pull-out i.n removed, if sufficient torque is available. The field is automatically applied if the motor synchronizes on reluctance torque. The control is calibrated at the factory and no field adjustment is required. The opti-... 

Driver. If steam is available, a common choice is a steam turbine driver for the main pump and an electric motor for standby. Some plants prefer two electric motor-driven pumps. Give the minimum steam condition. Give the expected voltage drop on the electric system if more than 10% is expected, especially on large systems. 

---