Loading results

Induction furnaces utilize the phenomena of electromagnetic induction to produce an electric current in the load or workpiece. This current is a result of a varying magnetic field created by an alternating current in a cod that typically surrounds the workpiece. Power to heat the load results from the passage of the electric current through the resistance of the load. Physical contact between the electric system and the material to be heated is not essential and is usually avoided. Nonconducting materials cannot be heated directiy by induction fields. 

Equipment, and type of sludge Loading Resultant soHds content, wt %... 

The next task is to determine the plaeement of the eompensating zero and pole within the error amplifier. The zero is plaeed at the lowest frequency manifestation of the filter pole. Since for the voltage-mode controlled flyback converter, and the current-mode controlled flyback and forward converters, this pole s frequency changes in response to the equivalent load resistance. The lightest expected load results in the lowest output filter pole frequency. The error amplifier s high frequency compensating pole is placed at the lowest anticipated zero frequency in the control-to-output curve cause by the ESR of the capacitor. In short ... 

The HVAC system is quite often not simulated but dimensioned on the space load results of the simulation by using simpler tools. However, aspects of control and the related potential for optimization are then neglected. 

Impact loading The loading resulting from sudden changes in the motion state of rig components. 

A mast or derrick guyed by means of a wire rope shall have the wire rope sized so as to have a nominal strength of at least 2 times the maximum guy load resulting from a loading condition. 

Equation 4-65 indicates that increased tensile load results in decreased collapse pressure resistance. The decrement of collapse pressure resistance during normal DST operations is relatively small nevertheless, under certain conditions, it may be quite considerable. 

Balanced construction In woven RPs, equal parts of warp and fill fibers exist. Its construction is one in which reactions to tension and compression loads result in extension or compression deformations only, and... 

However, the field of polymer day silicate has only started to speed up recently, mixing the appropriate modified layered silicate with synthetic layered silicates has long been known (Theng, 1979). The interest in these materials came from two important findings, first has been reported by Toyota research group of a Nylon-6 (N6)/Na-MMT nano-composites (Okada et ah, 1990) where very small amounts of layered silicate loadings resulted in the improvements of thermal and mechanical properties and second the findings of Vaia et ah (1993) about the... 

A basic emission load resulting from agriculture involves the calculation of greenhouse gases in the field phase. In the context of comparing the formation of greenhouse gas emissions in... 

The loop for the 2nd-D was loaded with the effluent of the 1 st-D at 50 pL/min for 1 min 58 s, and then the injection valve was turned to inject the 100 pL fraction for 2 s onto the 2nd-D HPLC. The flow rate was 5 mL/min, and the valve was turned back for the next loading, resulting in fractionation of the lst-D every 2 min. In this case less than 2% of the effluent from the 1 st-D was wasted during sample injection. The 2nd-D effluent eluted at 5 mL/min from the 2nd-D column, passed through a UV detector, and then was split by using a T-joint at approximately a 1/140 split ratio, resulting in a flow rate of ca. 36 pL/min going into the spray capillary for ESI-TOF-MS detection. 

As is seen from this latter figure, an increase of the solids loading results in a decrease in the cyclone attrition rate. This may be due to a cushioning effect of the increased solids concentration which is well known in comminution processes. This cushioning effect may be interpreted as a decrease in the efficiency T] of the abrasion process. If we assume r] to be a function of jJ and in its simplest form to follow an exponential function,... 

Loads Due to Differences in Expansion Characteristics. These loads result from differences in thermal expansion where materials with different thermal expansion coefficients are combined, as in bimetallic, lined, jacketed, or metallic-nonmetallic piping. 

---