Enabling

If the reaction involves more than one feed, it is not necessary to operate with the same low conversion on all the feeds. Using an excess of one of the feeds enables operation with a relatively high conversion of other feed material, and still inhibits series reactions. Consider again the series reaction system from Example 2.3 ... 

The penalty as a result of the constraint having been identified enables judgment as to whether it is acceptable or too expensive. If it is too expensive, there is a choice between two options ... 

Earlier processes (e.g. hydroforming) used MoO,i —AI2O3 catalysis but platinum-based catalysts are now extensively used, enabling longer on-stream times before catalyst replacement. 

A substance enabling two pieces of metal to be joined without oxidation. 

Modern methods of amino-acid and peptide analysis, have enabled the complete amino-acid sequence of a number of proteins to be worked out. The grosser structure can be determined by X-ray diffraction procedures. Proteins have molecular weights ranging from about 6 000 000 to 5 000 (although the dividing line between a protein and a peptide is ill defined). Edible proteins can be produced from petroleum and nutrients under fermentation. 

The sample can vary from 0.5 to 30 liters enabling the following ... 

Interest in this method has decreased since advances made in gas chromatography using high-resolution capillary columns (see article 3.3.3.) now enable complete identification by individual chemical component with equipment less expensive than mass spectrometry. 

Using this concept, Burdett developed a method in 1955 to obtain the concentrations in mono-, di- and polynuclear aromatics in gas oils from the absorbances measured at 197, 220 and 260 nm, with the condition that sulfur content be less than 1%. Knowledge of the average molecular weight enables the calculation of weight per cent from mole per cent. As with all methods based on statistical sampling from a population, this method is applicable only in the region used in the study extrapolation is not advised and usually leads to erroneous results. 

The specific nature of UV absorption for certain structures when combined with the high sensitivity of the method enables trace quantities (— 1 ppm) of molecules in a matrix transparent to UV beams to be analyzed. Benzene in cyclohexane is an example. 

Additionally, more sophisticated pulse sequences (the procedure is called spectral editing) enable one to obtain spectra, after addition or subtraction, where only the following are present (see, for example Bouquet, 1986) ... 

Comparing the overall concentrations of these different carbons designated generally as structural patterns , measured before and after a process such as FCC or hydrocracking (see Chapter 10), enables the conversion to be monitored the simple knowledge of the percentage of condensed aromatic carbon of a feedstock gives an indication of its tendency to form coke. 

The resolution of capillary columns enables the separation of all principal components of a straight-run gasoline. The most frequently used stationary phases are silicone-based, giving an order of hydrocarbon elution times close to the order of increasing boiling point. 

This method follows the ASTM D 1159 and D 2710 procedures and the AFNOR M 07-017 standard. It exploits the capacity of the double olefinic bond to attach two bromine atoms by the addition reaction. Expressed as grams of fixed bromine per hundred grams of sample, the bromine number, BrN, enables the calculation of olefinic hydrocarbons to be made if the average molecular weight of a sufficiently narrow cut is known. 

Knowledge of physical properties of fluids is essential to the process engineer because it enables him to specify, size or verify the operation of equipment in a production unit. The objective of this chapter is to present a collection of methods used in the calculation of physical properties of mixtures encountered in the petroleum industry, different kinds of hydrocarbon components, and some pure compounds. 

The factor enabling interpolation of reduced properties of a pure compound or mixture between two reduced properties calculated on two reference fluids merits attention in order to understand its meaning. 

The principle of corresponding states enables the enthalpy of a liquid mixture to be expressed starting from that of an ideal gas mixture and a reduced correction for enthalpy ... 

The constants k- enable the improved representation of binary equilibria and should be carefully determined starting from experimental results. The API Technical Data Book has published the values of constants k j for a number of binary systems. The use of these binary interaction coefficients is necessary for obtaining accurate calculation results for mixtures containing light components such as ... 

First of all, a technical clarification is necessary in the wider sense, motor fuels are chemical compounds, liquid or gas, which are burned in the presence of air to enable thermal engines to run gasoline, diesel fuel, jet fuels. The term heating fuel is reserved for the production of heat energy in boilers, furnaces, power plants, etc. 

More general techniques covering a wider range employ gas chromatography (Durand et al., 1987). This enables identification and analysis of the nearly 200 gasoline components whose octane numbers are known. 

The diesel engine takes in and compresses the air. The fuel is injected into the cylinder in atomized form at the end of the compression stroke and is vaporized in the air. Ignition begins by auto-ignition in one or several zones in the combustion chamber where the conditions of temperature, pressure and concentration combine to enable combustion to start. 

To avoid these problems, refiners commonly use additives called detergents" (Hall et al., 1976), (Bert et al., 1983). These are in reality surfactants made from molecules having hydrocarbon chains long enough to ensure their solubility in the fuel and a polar group that enables them to be absorbed on the walls and prevent deposits from sticking. The most effective chemical structures are succinimides, imides, and fatty acid amines. The required dosages are between 500 and 1000 ppm of active material. 

There are, however, technological means available to burn incompletely desulfurized fuels at the same time minimizing SO2 emissions. In the auto-desulfurizing AUDE boiler developed by IFF, the effluent is treated in place by an absorbent based on lime and limestone calcium sulfate is obtained. This system enables a gas desulfurization of 80% it requires nevertheless a relatively large amount of solid material, on the order of 200 kg per ton of fuel. 

This justifies all the work undertaken to arrive at fuel denitrification which, as is well known, is difficult and costly. Moreover, technological improvements can bring considerable progress to this field. That is the case with low NO burners developed at IFF. These consist of producing separated flame jets that enable lower combustion temperatures, local oxygen concentrations to be less high and a lowered fuel s nitrogen contribution to NOj. formation. In a well defined industrial installation, the burner said to be of the low NO type can attain a level of 350 mg/Nm, instead of the 600 mg/Nm with a conventional burner. 

The measurement of the vapor pressure and flash point of crude oils enables the light hydrocarbon content to be estimated. 

The determination of properties for each cut enables curves to be obtained for yields and properties as well as curves for iso-properties that are useful in the economic analyses of crude oils. 

All the analytical results are represented as curves that enable easy and rational utilization. 

Showing the results as curves enables manual calculations to be made which are often useful in rough estimates. 

This type of study, applied over all the cuts, enables the refinery flow scheme to be defined in order to satisfy a given set of market conditions starting from one or more crude oil feedstocks. 

A comparison of overall treatment costs (purchase and refining) for several crude oils enables the refiner to establish his feedstock requirements and to satisfy the market needs under the most economical conditions. 

Vacuum distillation of the atmospheric residue complements primary distillation, enabli r.ecoyery of heavy distillate cuts from atmospheric residue that will un r o further conversion or will serve as lube oil bases. The vacuum residue containing most of the crude contaminants (metals, salts, sediments, sulfur, nitrogen, asphaltenes, Conradson carbon, etc.) is used in asphalt manufacture, for heavy fuel-oil, or for feed for others conversion processes. 

This process thus enables gasoline production to be increased if the propylene can not be used for petrochemical manufacture. It recovers ethylene economically from fuel-gas. 

In a first phase, the diagram for processing oil fractions features the addition of complementary units that enable the production of unleaded gasoline such as ... 

All drilling activity will be carried out by the drill crew which usually works eight or twelve hour shifts. The driller and assistant driller will man the drilling console on the rig floor from where instrumentation will enable them to monitor and control the drilling parameters, specifically ... 

The objective of an EIA Is to document the potential physical, biological, social and health effects of a planned activity. This will enable decision makers to determine whether an activity is acceptable and if not, identify possible alternatives. Typically, ElA s will be carried out for... 

The non-hydrocarbon components of crude oil may be small in volume percent, typically less than 1 %, but their influence on the product quality and the processing requirements can be considerable. It is therefore important to identify the presence of these components as early as possible, and certainly before the field development planning stage, to enable the appropriate choice of processing facilities and materials of construction to be made. 

---