Water, acid chloride

When treated with water, acid chlorides are hydrolyzed to give carboxylic acids. 

Method (1) is most frequently used for aliphatic acid amides, while Methods (2a), (2b) and (zc) are used most frequently for aromatic acid amides. Of the last three methods, the Acid Chloride Method (zb) is the most rapid and certain. The Ester Method (za) is practicable only when the amide is insoluble in water, and even then is often very slow unless the ester itself is appreciabb soluble in the aqueous ammonia solution. 

Action of silver nitrate. Acidify 2 ml. of aqueous AgNOj solution with dil. HNO3 and add the acid chloride drop by drop with shaking. Acetyl chloride and benzoyl chloride give a precipitate of AgCl. Filter, wash with water, and then with methylated spirit to remove any benzoic acid the AgCl remains. 

Almost insoluble in cold water. Higher alcohols (including benzyl alcohol), higher phenols (e.g., naphthols), metaformaldehyde, paraldehyde, aromatic aldehydes, higher ketones (including acetophenone), aromatic acids, most esters, ethers, oxamide and domatic amides, sulphonamides, aromatic imides, aromatic nitriles, aromatic acid anhydrides, aromatic acid chlorides, sulphonyl chlorides, starch, aromatic amines, anilides, tyrosine, cystine, nitrocompounds, uric acid, halogeno-hydrocarbons, hydrocarbons. 

Stopper the side arm of a 25 or 50 ml. distilling flask and fit a vertical water condenser into the neck. Place 0-5-1 -0 g. of the dry acid (finely powdered if it is a solid) into the flask, add 2-5-5 0 ml. of redistilled thionyl chloride and reflux gently for 30 minutes it is advisable to place a plug of cotton wool in the top of the condenser to exclude moisture. Rearrange the condenser and distil off the excess of thionyl chloride t (b.p. 78°). The residue in the flask consists of the acid chloride and can be converted into any of the derivatives given below. 

Amides. TVeat the acid chloride cautiously with about 20 parts of concentrated ammonia solution (sp. gr. 0 - 88) and warm for a few moments. If no solid separates on cooling, evaporate to dryness on a water bath. Recrystallise the crude amide from water or dilute alcohol. 

Alternatively, dissolve or suspend the acid chloride in 5-10 ml. of dry ether or dry benzene, and pass in dry ammonia gas. If no solid separates, evaporate the solvent. Recrystallise the amide from water or dilute alcohol. 

Anilides. Dilute the acid chloride with 5 ml. of pure ether (or benzene), and add a solution of 2 g. of pure aniline in 15-20 ml. of the same solvent until the odour of the acid chloride has disappeared excess of aniline is not harmful. Shake with excess of dilute hydrochloric acid to remove aniline and its salts, wash the ethereal (or benzene) layer with 3-5 ml. of water, and evaporate the solvent [CAUTION ] Recrystallise the anilide from water, dilute alcohol or benzene - light petroleum (b.p. 60-80°). 

The above simple experiments illustrate the more important properties of aliphatic acid chlorides. For characterisation, the general procedure is to hydrolyse the acid chloride by warming with dilute alkali solution, neutralise the resulting solution with dilute hydrochloric acid (phenol-phthalein), and evaporate to dryness on a water bath. The mixture of the sodium salt of the acid and sodium chloride thus obtained may be employed for the preparation of solid esters as detailed under Aliphatic Acids, Section 111,85. The anilide or p-toluidide may be prepared directly from the acid chloride (see (iii) above and Section III,85,i). 

Fit a reflux condenser into the short neck of a 125 ml. Claisen flask, a separatory funnel into the long neck, and plug the side arm with a small cork (compare Fig. Ill, 31, 1). Place 58 g. (62 ml.) of commercial n-caproic acid (1) in the flask and heat on a water hath. Add 75 g. (46 ml.) of redistilled thionyl chloride through the separatory funnel during 45 minutes shake the flask from time to time to ensure thorough mixing. Reflux the mixture for 30 minutes. Arrange the apparatus for distillation from an air bath (Fig. II, 5, 3) the excess of thionyl chloride passes over flrst, followed by n-caproyl chloride at 145-155° (mainly at 150-155°). The yield of acid chloride is 56 g. 

Place 125 ml. of concentrated ammonia solution (sp. gr. 0-88) in a 600 ml. beaker and surround the latter with crushed ice. Stir the ammonia solution mechanically, and introduce the n-caproyl chloride slowly by means of a suitably supported separatory funnel with bent stem. The rate of addition must be adjusted so that no white fumes are lost. The amide separates immediately. Allow to stand in the ice water for 15 minutes after all the acid chloride has been introduced. Filter oflF the amide at the pump use the flltrate to assist the transfer of any amide remaining in the beaker to the Alter (2). Spread the amide on sheets of Alter or drying paper to dry in the air. The crude n-capro-amide (30 g.) has m.p. 98-99° and is sufficiently pure for conversion into the nitrile (Section 111,112) (3). Recrystallise a small quantity of the amide by dissolving it in the minimum volume of hot water and allowing the solution to cool dry on filter paper in the air. Pure n-caproamide has m.p. 100°. 

Dissolve 0 01 g. equivalent of the amino acid in 0 03 g. equivalent of N sodium hydroxide solution and cool to 5° in a bath of ice. Add, with rapid stirring, 0 -01 g. equivalent of 2 4-dichlorophenoxyacetyl chloride dissolved in 5 ml. of dry benzene at such a rate (5-10 minutes) that the temperature of the mixture does not rise above 15° if the reaction mixture gels after the addition of the acid chloride, add water to thin it. Remove the ice bath and stir for 2-3 hours. Extract the resulting mixture with ether, and acidify the aqueous solution to Congo red with dilute hydrochloric acid. Collect the precipitate by filtration and recrystallise it from dilute alcohol. 

Vinylacetic acid. Place 134 g. (161 ml.) of allyl cyanide (3) and 200 ml. of concentrated hydrochloric acid in a 1-htre round-bottomed flask attached to a reflux condenser. Warm the mixture cautiously with a small flame and shake from time to time. After 7-10 minutes, a vigorous reaction sets in and the mixture refluxes remove the flame and cool the flask, if necessary, in cold water. Ammonium chloride crystallises out. When the reaction subsides, reflux the mixture for 15 minutes. Then add 200 ml. of water, cool and separate the upper layer of acid. Extract the aqueous layer with three 100 ml. portions of ether. Combine the acid and the ether extracts, and remove the ether under atmospheric pressure in a 250 ml. Claisen flask with fractionating side arm (compare Fig. II, 13, 4) continue the heating on a water bath until the temperature of the vapour reaches 70°. Allow the apparatus to cool and distil under diminished pressure (compare Fig. II, 20, 1) , collect the fraction (a) distilling up to 71°/14 mm. and (6) at 72-74°/14 mm. (chiefly at 72 5°/ 14 mm.). A dark residue (about 10 ml.) and some white sohd ( crotonio acid) remains in the flask. Fraction (6) weighs 100 g. and is analytically pure vinylacetic acid. Fraction (a) weighs about 50 g. and separates into two layers remove the water layer, dry with anhydrous sodium sulphate and distil from a 50 ml. Claisen flask with fractionating side arm a further 15 g. of reasonably pure acid, b.p. 69-70°/12 mm., is obtained. 

Method 2. Place a 3 0 g. sample of the mixture of amines in a flask, add 6g. (4-5 ml.) of benzenesulphonyl chloride (or 6 g. of p-toluenesulphonyl chloride) and 100 ml. of a 5 per cent, solution of sodium hydroxide. Stopper the flask and shake vigorously until the odour of the acid chloride has disappeared open the flask occasionally to release the pressure developed by the heat of the reaction. AUow the mixture to cool, and dissolve any insoluble material in 60-75 ml. of ether. If a solid insoluble in both the aqueous and ether layer appears at this point (it is probably the sparingly soluble salt of a primary amine, e.g., a long chain compound of the type CjH5(CH2) NHj), add 25 ml. of water and shake if it does not dissolve, filter it off. Separate the ether and aqueous layers. The ether layer will contain the unchanged tertiary amine and the sulphonamide of the secondary amine. Acidify the alkaline aqueous layer with dilute hydrochloric acid, filter off the sulphonamide of the primary amine, and recrystaUise it from dilute alcohol. Extract the ether layer with sufficient 5 per cent, hydrochloric acid to remove all the tertiary amine present. Evaporate the ether to obtain the sulphonamide of the secondary amine recrystaUise it from alcohol or dilute alcohol. FinaUy, render the hydrochloric acid extract alkaline by the addition of dilute sodium hydroxide solution, and isolate the tertiary amine. 

The procedure is to pass purified hydrogen through a hot solution of the pure acid chloride in toluene or xylene in the presence of the catalyst the exit gases are bubbled through water to absorb the hydrogen chloride, and the solution is titrated with standard alkali from time to time so that the reduction may be stopped when the theoretical quantity of hydrogen chloride has been evolved. Further reduction would lead to the corresponding alcohol and hydrocarbon ... 

To the cold acid chloride add 175 ml. of pure carbon disulphide, cool in ice, add 30 g, of powdered anhydrous aluminium chloride in one lot, and immediately attach a reflux condenser. When the evolution of hydrogen chloride ceases (about 5 minutes), slowly warm the mixture to the boiling point on a water bath. Reflux for 10 minutes with frequent shaking the reaction is then complete. Cool the reaction mixture to 0°, and decompose the aluminium complex by the cautious addition, with shaking, of 100 g. of crushed ice. Then add 25 ml. of concentrated hydrochloric acid, transfer to a 2 htre round-bottomed flask and steam distil, preferably in the apparatus, depicted in Fig. II, 41, 3 since the a-tetralone is only moderately volatile in steam. The carbon disulphide passes over first, then there is a definite break in the distillation, after whieh the a-tetralone distils completely in about 2 htres of distillate. 

In a modification the acid chloride is treated with excess of dry pyridine whereby the addition complex ArCOCl. CgHjN is formed decomposition of the latter with water aflFords the acid anhydride ... 

Most aromatic acid chlorides impart a strongly acid reaction when shaken with water (compare Section 111,88). All are completely hydrolysed by boiling with solutions of caustic alkalis and yield no product volatile from the alkaline solution (compare Eaters, Sections 111,106 and IV, 183). They may be distinguished from acids by their facile reactions with alcohols (compare Section 111,27), phenols (compare Section IV,114), and amines (compare Sections 111,123 and IV.lOO). 

Triiodobenzoyl chloride. Reflux 5 g. of 3 4 5-triiodo-benzoic acid, m.p. 289-290°, gently with 10 ml. of redistilled thionyl chloride for 2 hours. Distil off the excess of thionyl chloride on a water bath, and recrystallise the residue from carbon tetrachloride - light petroleum with the use of a little decolourising charcoal. The yield of the acid chloride (bright yellow needles, m.p. 138°) is 3-8 g. it keeps well in a stoppered bottle. 

Neutrahse about one third of the filtrate with 5N sodium hydroxide and add a further 2 ml. of the alkah solution. Add 1 ml. of benzoyl chloride and stir until the odour of the acid chloride disappears. Collect the solid by suction filtration, wash it with water until free from alkah, and then recrystalhse it from dilute alcohol. The product is the dibenzoyl derivative of hexamethylenediamine and melts at 159°. 

Chloroacetyl chloride [79-04-9] (CICH2COCI) is the corresponding acid chloride of chloroacetic acid (see Acetyl chloride). Physical properties include mol wt 112.94, C2H2CI2O, mp —21.8 C, bp 106°C, vapor pressure 3.3 kPa (25 mm Hg) at 25°C, 12 kPa (90 mm Hg) at 50°C, and density 1.4202 g/mL and refractive index 1.4530, both at 20°C. Chloroacetyl chloride has a sharp, pungent, irritating odor. It is miscible with acetone and bensene and is initially insoluble in water. A slow reaction at the water—chloroactyl chloride interface, however, produces chloroacetic acid. When sufficient acid is formed to solubilize the two phases, a violent reaction forming chloroacetic acid and HCl occurs. 

A.gllsethionates. These are among the oldest of the synthetic detergents and were developed ia Germany to overcome problems of hard water. They are prepared by reaction of fatty acid chlorides with a salt of isethionic acid, ie, 2-hydroxyethanesulfonic acid [107-36-8]. These detergents have moderate foaming properties and have seen only limited use ia shampoos. 

Hydrogen Chloride—Water System. Hydrogen chloride is highly soluble in water and this aqueous solution does not obey Henry s law at ah concentrations. Solubhity data are summarized in Table 5. The relationship between the pressure and vapor composition of unsaturated aqueous hydrochloric acid solutions is given in Reference 12. The vapor—Hquid equiHbria for the water—hydrogen chloride system at pressures up to 1632 kPa and at temperatures ranging from —10 to +70° C are documented in Reference 13. 

Interfdci l Composite Membra.nes, A method of making asymmetric membranes involving interfacial polymerization was developed in the 1960s. This technique was used to produce reverse osmosis membranes with dramatically improved salt rejections and water fluxes compared to those prepared by the Loeb-Sourirajan process (28). In the interfacial polymerization method, an aqueous solution of a reactive prepolymer, such as polyamine, is first deposited in the pores of a microporous support membrane, typically a polysulfone ultrafUtration membrane. The amine-loaded support is then immersed in a water-immiscible solvent solution containing a reactant, for example, a diacid chloride in hexane. The amine and acid chloride then react at the interface of the two solutions to form a densely cross-linked, extremely thin membrane layer. This preparation method is shown schematically in Figure 15. The first membrane made was based on polyethylenimine cross-linked with toluene-2,4-diisocyanate (28). The process was later refined at FilmTec Corporation (29,30) and at UOP (31) in the United States, and at Nitto (32) in Japan. 

Figure 4a represents interfacial polymerisation encapsulation processes in which shell formation occurs at the core material—continuous phase interface due to reactants in each phase diffusing and rapidly reacting there to produce a capsule shell (10,11). The continuous phase normally contains a dispersing agent in order to faciUtate formation of the dispersion. The dispersed core phase encapsulated can be water, or a water-immiscible solvent. The reactant(s) and coreactant(s) in such processes generally are various multihmctional acid chlorides, isocyanates, amines, and alcohols. For water-immiscible core materials, a multihmctional acid chloride, isocyanate or a combination of these reactants, is dissolved in the core and a multihmctional amine(s) or alcohol(s) is dissolved in the aqueous phase used to disperse the core material. For water or water-miscible core materials, the multihmctional amine(s) or alcohol(s) is dissolved in the core and a multihmctional acid chloride(s) or isocyanate(s) is dissolved in the continuous phase. Both cases have been used to produce capsules. 

Figure 5 illustrates the type of encapsulation process shown in Figure 4a when the core material is a water-immiscible Hquid. Reactant X, a multihmctional acid chloride, isocyanate, or combination of these reactants, is dissolved in the core material. The resulting mixture is emulsified in an aqueous phase that contains an emulsifier such as partially hydroly2ed poly(vinyl alcohol) or a lignosulfonate. Reactant Y, a multihmctional amine or combination of amines such as ethylenediamine, hexamethylenediamine, or triethylenetetramine, is added to the aqueous phase thereby initiating interfacial polymerisation and formation of a capsule shell. If reactant X is an acid chloride, base is added to the aqueous phase in order to act as an acid scavenger. 

Because almost any diacid can be leaddy converted to the acid chloride, this reaction is quite versatile and several variations have been developed. In the interfacial polymerization method the reaction occurs at the boundary of two phases one contains a solution of the acid chloride in a water-immiscible solvent and the other is a solution of the diamine in water with an inorganic base and a surfactant (48). In the solution method, only one phase is present, which contains a solution of the diamine and diacid chloride. An organic base is added as an acceptor for the hydrogen chloride produced in the reaction (49). Following any of these methods of preparation, the polymer is exposed to water and the acid chloride end is converted to a carboxyhc acid end. However, it is very difficult to remove all traces of chloride from the polymer, even with repeated washings with a strong base. 

Carboxylic Acid Group. Sorbic acid undergoes the normal acid reactions forming salts, esters, amides, and acid chlorides. Industrially, the most important compound is the potassium salt because of stabiUty and high water solubiUty. Sodium sorbate [7757-81-5] (E,E form [42788-83-0]) is less stable and not commercially available. The calcium salt [7492-55-9] which has limited solubiUty, has use in packaging (qv) materials. 

In another process, strontium sulfate can be converted to strontium carbonate direcdy by a metathesis reaction wherein strontium sulfate is added to a solution of sodium carbonate to produce strontium carbonate and leave sodium sulfate in solution (6). Prior to this reaction, the finely ground ore is mixed with hydrochloric acid to convert the calcium carbonates and iron oxides to water-soluble chlorides. 

The viscous fatty acid chloride is mixed with soHd sodium isothionate and is heated under vacuum and agitation without water or solvent HCl is evolved, leaving the product as a finely divided powder. The direct esterification of fatty acid and sodium isethionate has been patented (69). 

Methylene chloride is one of the more stable of the chlorinated hydrocarbon solvents. Its initial thermal degradation temperature is 120°C in dry air (1). This temperature decreases as the moisture content increases. The reaction produces mainly HCl with trace amounts of phosgene. Decomposition under these conditions can be inhibited by the addition of small quantities (0.0001—1.0%) of phenoHc compounds, eg, phenol, hydroquinone, -cresol, resorcinol, thymol, and 1-naphthol (2). Stabilization may also be effected by the addition of small amounts of amines (3) or a mixture of nitromethane and 1,4-dioxane. The latter diminishes attack on aluminum and inhibits kon-catalyzed reactions of methylene chloride (4). The addition of small amounts of epoxides can also inhibit aluminum reactions catalyzed by iron (5). On prolonged contact with water, methylene chloride hydrolyzes very slowly, forming HCl as the primary product. On prolonged heating with water in a sealed vessel at 140—170°C, methylene chloride yields formaldehyde and hydrochloric acid as shown by the following equation (6). 

Ben zotricbl oride is hydrolyzed to benzoic acid by hot water, concentrated sulfuric acid, or dilute aqueous alkaH. Benzoyl chloride [98-88-4] is produced by the reaction of benzotrichloride with an equimolar amount of water or an equivalent of benzoic acid. The reaction is catalyzed by Lewis acids such as ferric chloride and zinc chloride (25). Reaction of benzotrichloride with other organic acids or with anhydrides yields mixtures of benzoyl chloride and the acid chloride derived from the acid or anhydride (26). Benzo triflu oride [98-08-8] is formed by the reaction of benzotrichloride with anhydrous hydrogen fluoride under both Hquid- and vapor-phase reaction conditions. 

---