Break, definition

To the cold acid chloride add 175 ml. of pure carbon disulphide, cool in ice, add 30 g, of powdered anhydrous aluminium chloride in one lot, and immediately attach a reflux condenser. When the evolution of hydrogen chloride ceases (about 5 minutes), slowly warm the mixture to the boiling point on a water bath. Reflux for 10 minutes with frequent shaking the reaction is then complete. Cool the reaction mixture to 0°, and decompose the aluminium complex by the cautious addition, with shaking, of 100 g. of crushed ice. Then add 25 ml. of concentrated hydrochloric acid, transfer to a 2 htre round-bottomed flask and steam distil, preferably in the apparatus, depicted in Fig. II, 41, 3 since the a-tetralone is only moderately volatile in steam. The carbon disulphide passes over first, then there is a definite break in the distillation, after whieh the a-tetralone distils completely in about 2 htres of distillate. 

Because it is desirable to break a peptide this way, some flexibility is required in the rigorous definition of sp -sp single bond. In particular, the dative Cqj-N bond in the backbone of a peptide is considered to be such a bond since the definition is based on the number of neighbors — four for carbon, three for nitrogen, two for Oxygen, etc. If this were not the case, you couldn t break a protein into classical and quantum regions at all. 

The definition of polymer thermal stabiUty is not simple owing to the number of measurement techniques, desired properties, and factors that affect each (time, heating rate, atmosphere, etc). The easiest evaluation of thermal stabiUty is by the temperature at which a certain weight loss occurs as observed by thermogravimetric analysis (tga). Early work assigned a 7% loss as the point of stabiUty more recentiy a 10% value or the extrapolated break in the tga curve has been used. A more reaUstic view is to compare weight loss vs time at constant temperature, and better yet is to evaluate property retention time at temperature one set of criteria has been 177°C for 30,000 h, or 240°C for 1000 h, or 538°C for 1 h, or 816°C for 5 min (1). 

Definitions of the commonly measured tensile properties are as follows Unear density (tex) is the weight in grams of 1000 m of yam. Tenacity is the tensile stress at break and is expressed in force-per-unit linear density of unstrained specimen, N /tex. Knot tenacity is the tensile stress required to mpture a single strand of yam with an overhand knot tied in the segment of sample between the testing clamps. It is expressed as force-per-unit linear density and is an approximate measure of the britdeness of the yam. Toop tenacity is the tensile stress required to mpture yam when one strand of yam is looped through... 

Thermal treatment is used to destroy, break down, or aid in the desorption of contaminants in gases, vapors, Hquids, sludges, and soHds. There are a variety of thermal processes that destroy contaminants, most of which are classified as incineration. Incineration HteraHy means to become ash (from Medieval Latin, incinerare in or into ashes). With respect to the incineration of hazardous wastes regulated in the United States, however, there is a strict legal definition of what constitutes an incinerator. The Resource Conservation and Recovery Act (RCRA) definition of incinerator at 40 CFR 260.10 is... 

As for the tenacity, which describes the fiber s resistance to the action of the tensile force, the quantitative index assumed most often is the tensile strength (crj (cN/tex). For the quantitative assessment of tenacity an index of mechanical long life (t) is used, proposed by Zurkow and Abasow [46,47]. This index defines the time after which, when applying a definite tensile strength and a definite temperature, the fiber breaks. 

From a practical viewpoint toughness is readily understood, but technically there tends to be no scientific method of measuring it. One definition of toughness is simply the energy required to break the plastic. This... 

As has been indicated, since there is a ring isotope effect there must be a degree of C-H bond breaking in the transition state of the rate-determining stage. Clearly further work is required in this system before a definitive mechanism can be established for the intramolecular rearrangement. 

Let us note that this definition of y breaks the limits of the Kielson-Storer model and can cause a few contradictions in interpretation of results. If the measured cross-section oj appears to be greater than oo, then, according to (3.45), the sought y does not exist. To be exact, this assertion is valid relative to the cross-section of the rotational energy relaxation oe = (1 — y2)oot since y2 is always positive. As to oj, taking into account the domain of negative values of y, corresponding to the anticorrelated case (see Chapter 2), formula (3.45) fails to define y when oj > 2co. 

The necessity of the statistical approach has to be stressed once more. Any statement in this topic has a definitely statistical character and is valid only with a certain probability and in certain range of validity, limited as to the structural conditions and as to the temperature region. In fact, all chemical conceptions can break dovra when the temperature is changed too much. The isokinetic relationship, when significantly proved, can help in defining the term reaction series it can be considered a necessary but not sufficient condition of a common reaction mechanism and in any case is a necessary presumption for any linear free energy relationship. Hence, it does not at all detract from kinetic measurements at different temperatures on the contrary, it gives them still more importance. 

Never break a single bond when drawing resonance structures. By definition, resonance stractures must have aU the same atoms connected in the same order. 

---