Flame ionization.

The chromatogram can finally be used as the series of bands or zones of components or the components can be eluted successively and then detected by various means (e.g. thermal conductivity, flame ionization, electron capture detectors, or the bands can be examined chemically). If the detection is non-destructive, preparative scale chromatography can separate measurable and useful quantities of components. The final detection stage can be coupled to a mass spectrometer (GCMS) and to a computer for final identification. 

Some techniques have been described that are based on the concept of flame ionization used in gas chromatography. The results are generally unsatisfactory because it is necessary to evaporate the solvent prior to introducing the mixture into the detector. 

This type of analysis requires several chromatographic columns and detectors. Hydrocarbons are measured with the aid of a flame ionization detector FID, while the other gases are analyzed using a katharometer. A large number of combinations of columns is possible considering the commutations between columns and, potentially, backflushing of the carrier gas. As an example, the hydrocarbons can be separated by a column packed with silicone or alumina while O2, N2 and CO will require a molecular sieve column. H2S is a special case because this gas is fixed irreversibly on a number of chromatographic supports. Its separation can be achieved on certain kinds of supports such as Porapak which are styrene-divinylbenzene copolymers. This type of phase is also used to analyze CO2 and water. 

The hydrocarbons are separated in another column and analyzed by a flame ionization detector, FID. As an example, Figure 3.13 shows the separation obtained for a propane analyzed according to the ISO 7941 standard. Note that certain separations are incomplete as in the case of ethane-ethylene. A better separation could be obtained using an alumina capillary column, for instance. 

Ecole Nationale Superieure du Petrole et des Moteurs Formation Industrie end point (or FBP - final boiling point) electrostatic precipitation ethyl tertiary butyl ether European Union extra-urban driving cycle volume fraction distilled at 70-100-180-210°C Fachausschuss Mineralol-und-Brennstoff-Normung fluid catalytic cracking Food and Drug Administration front end octane number fluorescent indicator adsorption flame ionization detector... 

Flame Ionization Detector Combustion of an organic compound in an Hz/air flame results in a flame rich in electrons and ions. If a potential of approximately 300 V is applied across the flame, a small current of roughly 10 -10 A develops. When amplified, this current provides a useful analytical signal. This is the basis of the popular flame ionization detector (FID), a schematic of which is shown in Figure 12.22. 

Other Detectors Two additional detectors are similar in design to a flame ionization detector. In the flame photometric detector optical emission from phosphorus and sulfur provides a detector selective for compounds containing these elements. The thermionic detector responds to compounds containing nitrogen or phosphorus. 

Environmental Analysis One of the most important environmental applications of gas chromatography is for the analysis of numerous organic pollutants in air, water, and wastewater. The analysis of volatile organics in drinking water, for example, is accomplished by a purge and trap, followed by their separation on a capillary column with a nonpolar stationary phase. A flame ionization, electron capture, or... 

Despite their importance, gas chromatography and liquid chromatography cannot be used to separate and analyze all types of samples. Gas chromatography, particularly when using capillary columns, provides for rapid separations with excellent resolution. Its application, however, is limited to volatile analytes or those analytes that can be made volatile by a suitable derivatization. Liquid chromatography can be used to separate a wider array of solutes however, the most commonly used detectors (UV, fluorescence, and electrochemical) do not respond as universally as the flame ionization detector commonly used in gas chromatography. 

Although aimed at the introductory class, this simple experiment provides a nice demonstration of the use of GG for a qualitative analysis. Students obtain chromatograms for several possible accelerants using headspace sampling and then analyze the headspace over a sealed sample of charred wood to determine the accelerant used in burning the wood. Separations are carried out using a wide-bore capillary column with a stationary phase of methyl 50% phenyl silicone and a flame ionization detector. 

The principle of headspace sampling is introduced in this experiment using a mixture of methanol, chloroform, 1,2-dichloroethane, 1,1,1-trichloroethane, benzene, toluene, and p-xylene. Directions are given for evaluating the distribution coefficient for the partitioning of a volatile species between the liquid and vapor phase and for its quantitative analysis in the liquid phase. Both packed (OV-101) and capillary (5% phenyl silicone) columns were used. The GG is equipped with a flame ionization detector. 

This experiment provides an alternative approach to measuring the partition coefficient (Henry s law constant) for volatile organic compounds in water. A OV-101 packed column and flame ionization detector are used. 

Here is a challenge McMinn and co-workers investigated the effect of five factors for optimizing an H2-atmosphere flame ionization detector using a 2 factorial design. The factors and their levels were... 

Fisher s least significant difference a modified form of the f-test for comparing several sets of data. (p. 696) flame ionization detector a nearly universal GC detector in which the solutes are combusted in an H2/air flame, producing a measurable current, (p. 570)... 

Many kinds of detectors have been designed, ranging from the widely used, cheap but robust flame ionization (GC) or ultraviolet absorption type (LC) to the much more exciting and informative, if much more expensive, mass spectrometer. 

Schematic diagram of a flame ionization detector. Ions and electrons formed in the flame provide an electrically conducting path between the flame at earth potential and an insulated cylindrical metal electrode at high potential. surrounding the flame the flow of current is monitored, amplified, and passed to the recording system.

Flame emissivity Flame ionization Flameproofing cotton Flame resistance Flame-resistant fibers Flame retardancy Flame retardant... 

The special problems for vaUdation presented by chiral separations can be even more burdensome for gc because most methods of detection (eg, flame ionization detection or electron capture detection) in gc destroy the sample. Even when nondestmctive detection (eg, thermal conductivity) is used, individual peak collection is generally more difficult than in Ic or tic. Thus, off-line chiroptical analysis is not usually an option. Eortunately, gc can be readily coupled to a mass spectrometer and is routinely used to vaUdate a chiral separation. 

Reference methods for criteria (19) and hazardous (20) poUutants estabHshed by the US EPA include sulfur dioxide [7446-09-5] by the West-Gaeke method carbon monoxide [630-08-0] by nondispersive infrared analysis ozone [10028-15-6] and nitrogen dioxide [10102-44-0] by chemiluminescence (qv) and hydrocarbons by gas chromatography coupled with flame-ionization detection. Gas chromatography coupled with a suitable detector can also be used to measure ambient concentrations of vinyl chloride monomer [75-01-4], halogenated hydrocarbons and aromatics, and polyacrylonitrile [25014-41-9] (21-22) (see Chromatography Trace and residue analysis). 

Fig. 3. (a) Flame ionization detector (fid) response to an extract of commercially processed Valencia orange juice, (b) Gas chromatography—olfactometry (geo) chromatogram of the same extract. The abscissa in both chromatograms is a normal paraffin retention index scale ranging between hexane and octadecane (Kovats index). Dilution value in the geo is the -fold that the extract had to be diluted until odor was no longer detectable at each index. 

A flame-ionization, total hydrocarbon analyzer determines the THC, and the total carbon content is calculated as methane. Other methods include catalytic combustion to carbon dioxide, which may be deterrnined by a sensitive infrared detector of the nondispersive type. Hydrocarbons other than methane and acetylene are present only in minute quantities and generally are inert in most appHcations. 

Analytical Techniques. Sorbic acid and potassium sorbate are assayed titrimetricaHy (51). The quantitative analysis of sorbic acid in food or beverages, which may require solvent extraction or steam distillation (52,53), employs various techniques. The two classical methods are both spectrophotometric (54—56). In the ultraviolet method, the prepared sample is acidified and the sorbic acid is measured at 250 260 nm. In the colorimetric method, the sorbic acid in the prepared sample is oxidized and then reacts with thiobarbituric acid the complex is measured at - 530 nm. Chromatographic techniques are also used for the analysis of sorbic acid. High pressure Hquid chromatography with ultraviolet detection is used to separate and quantify sorbic acid from other ultraviolet-absorbing species (57—59). Sorbic acid in food extracts is deterrnined by gas chromatography with flame ionization detection (60—62). 

Various types of detector tubes have been devised. The NIOSH standard number S-311 employs a tube filled with 420—840 p.m (20/40 mesh) activated charcoal. A known volume of air is passed through the tube by either a handheld or vacuum pump. Carbon disulfide is used as the desorbing solvent and the solution is then analyzed by gc using a flame-ionization detector (88). Other adsorbents such as siUca gel and desorbents such as acetone have been employed. Passive (diffuse samplers) have also been developed. Passive samplers are useful for determining the time-weighted average (TWA) concentration of benzene vapor (89). Passive dosimeters allow permeation or diffusion-controlled mass transport across a membrane or adsorbent bed, ie, activated charcoal. The activated charcoal is removed, extracted with solvent, and analyzed by gc. Passive dosimeters with instant readout capabiUty have also been devised (85). 

The most widely used method of analysis for methylene chloride is gas chromatography. A capillary column medium that does a very good job in separating most chlorinated hydrocarbons is methyl silicone or methyl (5% phenyl) silicone. The detector of choice is a flame ionization detector. Typical molar response factors for the chlorinated methanes ate methyl chloride, 2.05 methylene chloride, 2.2 chloroform, 2.8 and carbon tetrachloride, 3.1, where methane is defined as having a molar response factor of 2.00. Most two-carbon chlorinated hydrocarbons have a molar response factor of about 1.0 on the same basis. 

Purity. Gas chromatographic analysis is performed utilizing a wide-bore capillary column (DB-1, 60 m x 0.32 mm ID x 1.0 //m film) and a flame ionization detector in an instmment such as a Hewlett-Packard 5890 gas chromatograph. A caUbration standard is used to determine response factors for all significant impurities, and external standard calculation techniques are used to estimate the impurity concentrations. AHyl chloride purity is deterrnined by difference. 

---