ASTM test

Property ASTM test method Homopolymer Copolymer... [Pg.56]

Testing. Melt index or melt flow rate at 190°C, according to ASTM D1238, is the test most frequently appHed to the characterization of commercial acetal resins. The materials are typically grouped or differentiated according to their melt flow rate. Several other ASTM tests are commonly used for the characterization and specification of acetal resins. [Pg.57]

The routine compositional and functional testing done on the adhesives includes gas chromatographic testing for purity, potentiometric titrations for acid stabilizer concentrations, accelerated thermal stabiUty tests for shelf life, fixture time cure speed tests, and assorted ASTM tests for tensile shear strengths, peel and impact strengths, and hot strengths. [Pg.178]

The most extensive body of tests are provided under the auspices of ASTM Standard methods. Specific ASTM test designations and descriptions are available (48). The other compendium of fire-retardant tests are contained ia Federal Test Method Standards 191A (49). [Pg.487]

One ASTM test procedure has suggested (24) that foamed plastics be classified as either rigid or flexible, a flexible foam being one that does not mpture when a 20 x 2.5 x 2.5 cm piece is wrapped around a 2.5 cm mandrel at a uniform rate of 1 lap/5 s at 15—25°C. Rigid foams are those that do mpture under this test. This classification is used in this article. [Pg.403]

Another ASTM test method. Potential Gum (D873), combines the existent gum and the oxidation stabihty tests to measure potential gum. A sample of gasoline is subjected to the oxidation stabihty test for 960 min, filtered to remove particulates, and then subjected to an existent gum test. The potential gum is expressed as the total (unwashed) gum in this test. [Pg.183]

Although there is no official ASTM test to measure the water handling properties of gasoline, there are a number of widely used industry tests. One uses a Waring Blender to simulate high shear (57), whereas another uses a wrist action shaker to simulate mild shear conditions (58). [Pg.187]

The bulk of hydrauhc fluids is specified and purchased on bid. Specifications and approval fists are issued by some manufacturers of hydraulic pumps and system components that require lubrication as well as power for control signal transmission. U.S. government military specifications for hydraulic fluids are fisted ia Table 12, and ASTM tests that are applicable to hydraulic fluids iaclude the foUowiag ... [Pg.269]

Aibitiary (qualitative) units given in ASTM test. [Pg.333]

Ionomer resins are produced in multiple grades to meet market needs, and prospective customers are provided with information on key processing parameters such as melt-flow index. Nominal values for many other properties are Hsted in product brochures. The ASTM test methods developed for general-purpose thermoplastic resins are appHcable to ionomers. No special methods have been introduced specifically for the ionomers. [Pg.408]

Properties ASTM test Extmsion, sheet General- -purpose injection mol ding Injection molding thin complex parts... [Pg.409]

Properties ASTM test Blow mol ding Injection molding... [Pg.410]

Floor poHshes typically are evaluated for gloss, appHcation and leveling properties, discoloration, sHp resistance, scratch resistance, heel-mark resistance, scuff resistance, damp-mopping and detergent resistance, repairabiHty, lack of sediment, and removabiHty (3). RecoatabiHty and formula stabiHty are also important. A review of test methods is available (35). More than 20 ASTM test methods for floor poHshes exist. From the standpoint of product safety, sHp resistance is a particularly important variable and many test methods are available (39). [Pg.210]

Property Nylon-6,6 Nylon-6 Nylon-11 Nylon-12 Nylon-6,9 Nylon-6,12 ASTM test method... [Pg.266]

Mechanical Properties. The performance of various polyester resin compositions can be distinguished by comparing the mechanical properties of thin castings (3 mm) of the neat resin defined in ASTM testing procedures (15). This technique is used widely to characterize subtle changes in flexural, tensile, and compressive properties that are generally overshadowed in highly filled or reinforced laminates. [Pg.320]

The most important general test methods are issued as ASTM Test Methods and are periodically updated by the Polyurethane Raw Materials Analysis Committee (PURMAC) of the Society for the Plastics Industry (SPI). PURMAC has collected all pertinent analytical methods in a manual (271). [Pg.367]

Property ASTM test method Polysulfone, % GR Polyethersulfone, % GR ... [Pg.466]

ASTM tests G21-70 and G22-76. Higher numbers are considered to correlate with the susceptibiUty of the plastic i to biodegradation. [Pg.478]

Property ASTM test method Desired range A B C... [Pg.535]

Table 7. ASTM Tests and Standards for Asphalt Shingles...

See also in sourсe #XX -- [ Pg.124 ]

See also in sourсe #XX -- [ Pg.283 , Pg.284 , Pg.285 , Pg.286 , Pg.287 , Pg.288 , Pg.289 , Pg.290 ]

See also in sourсe #XX -- [ Pg.124 , Pg.125 , Pg.126 , Pg.127 , Pg.128 , Pg.173 , Pg.175 , Pg.213 , Pg.238 ]

See also in sourсe #XX -- [ Pg.31 , Pg.32 , Pg.33 , Pg.47 ]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...