Rheological properties rheology

Rheological Properties. Rheological studies show that ammonia affects the compressive mechanical behavior of wood to a much higher extent than the tensile behavior (55,16). Since the compression strength is highly dependent on lignin content,... 

Rheological properties Rheology is the study of the deformation and flow of matter under the influence of an applied stress. The measurement of rheological properties is helpful to predict the physical properties of polymer nanocomposites during and after processing. Oberdisse [44] studied the rheological properties of a special nanocomposite material obtained by film formation of mixtures of colloidal silica and nanolatex solutions by means of uniaxial strain experiments. 

Basic raw materials are natural and synthetic polymers or monomers and prepolymers which can form such polymers. The polymers primarily impart the required strength (cohesion) to the adhesive layer. In many cases, however, they have adequate adhesion properties of their own. The adhesion properties may be improved by addition of resins or special adhesion promoters. Plasticizers and resins improve the flexibility of the polymers, increase the tack of the adhesives, or establish other required product properties, e.g., rheological properties. Rheological and other special properties can be influenced by adding fillers. Polymers are often dissolved in water or an organic solvent to achieve the wetting necessary for good adhesion. 

Rheological Properties. Rheological studies of the nanocomposites were performed using a Rheometrics Mechanical Spectrometer model 800 on 25mm diameter samples punched from the injection molded plaques. Dynamic oscillatory shear flow measurements of the nanocomposites were made in the linear regime of strain in a frequency range of 0.1 to 100 rad/s under a continuous nitrogen atmosphere. 

Additives Modifying the Rheological Properties of Lubricating Oils... 

It is very important, from one hand, to accept a hypothesis about the material fracture properties before physical model building because general view of TF is going to change depending on mechanical model (brittle, elasto-plastic, visco-elasto-plastic, ete.) of the material. From the other hand, it is necessary to keep in mind that the material response to loads or actions is different depending on the accepted mechanical model because rheological properties of the material determine type of response in time. The most remarkable difference can be observed between brittle materials and materials with explicit plastic properties. 

Luengo G ef a/1997 Thin film rheology and tribology of oonfined polymer melts oontrasts with bulk properties Macromolecules 30 2482-94... 

Most properties of linear polymers are controlled by two different factors. The chemical constitution of tire monomers detennines tire interaction strengtli between tire chains, tire interactions of tire polymer witli host molecules or witli interfaces. The monomer stmcture also detennines tire possible local confonnations of tire polymer chain. This relationship between the molecular stmcture and any interaction witli surrounding molecules is similar to tliat found for low-molecular-weight compounds. The second important parameter tliat controls polymer properties is tire molecular weight. Contrary to tire situation for low-molecular-weight compounds, it plays a fimdamental role in polymer behaviour. It detennines tire slow-mode dynamics and tire viscosity of polymers in solutions and in tire melt. These properties are of utmost importance in polymer rheology and condition tlieir processability. The mechanical properties, solubility and miscibility of different polymers also depend on tlieir molecular weights. 

Many properties of colloidal suspensions, such as their stability, rheology, and phase behaviour, are closely related to the interactions between the suspended particles. The background of the most important contributing factors to these interactions is discussed in this section. 

Doi, M. and Edwards, S.F., 1978. Dynamics of concentrated polymer systems 1. Brownian motion in equilibrium state, 2. Molecular motion under flow, 3. Constitutive equation and 4. Rheological properties. J. Cheni. Soc., Faraday Trans. 2 74, 1789, 1802, 1818-18.32. 

Most of the polymer s characteristics stem from its molecular stmcture, which like POE, promotes solubiUty in a variety of solvents in addition to water. It exhibits Newtonian rheology and is mechanically stable relative to other thermoplastics. It also forms miscible blends with a variety of other polymers. The water solubiUty and hot meltable characteristics promote adhesion in a number of appHcations. PEOX has been observed to promote adhesion comparable with PVP and PVA on aluminum foil, cellophane, nylon, poly(methyl methacrylate), and poly(ethylene terephthalate), and in composite systems improved tensile strength and Izod impact properties have been noted. 

Fats contribute to the rheological properties in flowable and pastry foods. By combining with starches to form a clathrate, a product different from the native starch is formed, eg, shortening in baked goods. The highly developed shortness of pies baked in eadier times resulted from the use of high levels of lard. The use of less fat in pie cmsts is evident, ie, the cmsts are harder and readily become soggy. 

LOY is characterized by low spinning tension, mostiy rheological effects, Httie orientation, amorphous stmcture, low tensde strength, and high elongation. The spun filament must be drawn, usually three to six times its initial length, and heat-treated before it develops useful properties. Nearly all PET staple is spun this way. 

Rheology. The rheology of foam is striking it simultaneously shares the hallmark rheological properties of soHds, Hquids, and gases. Like an ordinary soHd, foams have a finite shear modulus and respond elastically to a small shear stress. However, if the appHed stress is increased beyond the yield stress, the foam flows like a viscous Hquid. In addition, because they contain a large volume fraction of gas, foams are quite compressible, like gases. Thus foams defy classification as soHd, Hquid, or vapor, and their mechanical response to external forces can be very complex. 

One simple rheological model that is often used to describe the behavior of foams is that of a Bingham plastic. This appHes for flows over length scales sufficiently large that the foam can be reasonably considered as a continuous medium. The Bingham plastic model combines the properties of a yield stress like that of a soHd with the viscous flow of a Hquid. In simple Newtonian fluids, the shear stress T is proportional to the strain rate y, with the constant of proportionaHty being the fluid viscosity. In Bingham plastics, by contrast, the relation between stress and strain rate is r = where is... 

Foams have a wide variety of appHcations that exploit their different physical properties. The low density, or high volume fraction of gas, enable foams to float on top of other fluids and to fiU large volumes with relatively Httle fluid material. These features are of particular importance in their use for fire fighting. The very high internal surface area of foams makes them useful in many separation processes. The unique rheology of foams also results in a wide variety of uses, as a foam can behave as a soHd, while stiH being able to flow once its yield stress is exceeded. 

Solutions of rhamsan have high viscosity at low shear rates and low gum concentrations (90). The rheological properties and suspension capabiUty combined with excellent salt compatibihty, make it useful for several industrial apphcations including agricultural fertilizer suspensions, pigment suspensions, cleaners, and paints and coatings. 

Commercial Stabilizers. There is a great variety of commercial formulations utilizing the mixture of the alkaU and alkaline-earth metal salts and soaps. In many cases, products are custom formulated to meet the needs of a particular appHcation or customer. The acidic ligands used ia these products vary widely and have dramatic effects on the physical properties of the PVC formulations. The choice of ligands can affect the heat stabiHty, rheology, lubricity, plate-out tendency, clarity, heat sealabiHty, and electrical and mechanical properties of the final products. No single representative formulation can cover the variety of PVC appHcations where these stabilizers are used. 

The four key properties of inks are drying, rheology, color, and end use properties. Use properties are those considerations that determine how printed substrates function throughout all processing and usage from the time of printing throughout the useflil life of the printed product. 

Preformed Two-Piece Metal Containers. Ink vehicles for letterset printing of two-piece aluminum or steel containers are mainly based on special polyester vehicles used in conjunction with melamine cross-linkers. Short cycle ovens which dry inks in 1—5 seconds are now used and operate at temperatures as high as 350 °C. The rheology of these inks must be adjusted to the unique geometry of the press. Desired rheological properties are achieved by the use of additives as weU as extender pigments. 

Table 2. Rheological and Physical Properties of EMAA Copolymers, ...

---