Pushing

This term refers to highly refined lubricating oils for which dearomatization, in particular, has been pushed to the extreme. These products are sometimes designated by the expression liquid petrolatum . 

There are two categories of white oils technical white oils and medicinal white oils. The technical white oils, which are already highly dearomatized, are used for specialized lubricants, particularly in the textile industry, and also as components in cosmetics, as plasticizers in the rubber or plastics industries, or as emulsion bases for certain pulverized agriculture products. The medicinal white oils, whose dearomatization is pushed further still, are used in pharmaceuticals, or in the food industry, wherever residual oils might be in contact with food. 

All modern refineries have conversion units, designed to transform black effluent streams into lighter products gas, gasoline, diesel fuel. Among these conversion units, coking processes take place by pyrolysis and push the cracking reaction so far that the residue from the operation is very heavy it is called coke . 

An important safety feature on every modern rig is the blowout preventer (BOP). As discussed earlier on, one of the purposes of the drilling mud is to provide a hydrostatic head of fluid to counterbalance the pore pressure of fluids in permeable formations. However, for a variety of reasons (see section 3.6 Drilling Problems ) the well may kick , i.e. formation fluids may enter the wellbore, upsetting the balance of the system, pushing mud out of the hole, and exposing the upper part of the hole and equipment to the higher pressures of the deep subsurface. If left uncontrolled, this can lead to a blowout, a situation where formation fluids flow to the surface in an uncontrolled manner. 

A traditional abandonment process begins with a well killing operation in which produced fluids are circulated out of the well, or pushed ( bull headed ) into the formation, and replaced by drilling fluids heavy enough to contain any open formation pressures. Once... 

During take-off and landing, the wheels of modem aircraft are subject to great stress. New high-performance brake systems and aggressive environmental influences push the wheels closer and closer to their limit. These conditions as well as increased requirements for safety and quality control now necessitate that wheels are tested much more comprehensively than in the past. 

The fish block will be moved through the X-ray beam and the resulting image is studied on the high resolution monitor. The operator has the ability to judge a block as acceptable, rejectable or downgrade able via push-button. 

If neither the accept, downgrade or reject button is pushed during inspection, the block will automatically be out loaded after the time limit has expired. The accept/reject/downgrade buttons will flash prompting the inspector for a decision. 

One type of dislocation is the edge dislocation, illustrated in Fig. VII-7. We imagine that the upper half of the crystal is pushed relative to the lower half, and the sequence shown is that of successive positions of the dislocation. An extra plane, marked as full circles, moves through the crystal until it emerges at the left. The process is much like moving a rug by pushing a crease in it. 

There are many other experiments in which surface atoms have been purposely moved, removed or chemically modified with a scanning probe tip. For example, atoms on a surface have been induced to move via interaction with the large electric field associated with an STM tip [78]. A scaiming force microscope has been used to create three-dimensional nanostructures by pushing adsorbed particles with the tip [79]. In addition, the electrons that are tunnelling from an STM tip to the sample can be used as sources of electrons for stimulated desorption [80]. The tuimelling electrons have also been used to promote dissociation of adsorbed O2 molecules on metal or semiconductor surfaces [81, 82]. 

Parr B 2000 webpage http //net.chem.unc.edu/facultv/rap/cfrap01. html Professor Parr was among the first to push the density functional theory of Hohenberg and Kohn to bring it into the mainstream of electronic structure theory. For a good overview, see the book ... 

The atom will therefore experience a net restoring force pushing it back to the origin. If the light beams are red detuned F, then the Doppler shift of the atomic motion will introduce a velocity-dependent tenn to the restoring force such that, for small displacements and velocities, the total restoring force can be expressed as the sum of a tenn linear in velocity and a tenn linear in displacement. 

Figure C2.4.2. Schematic sideview of tlie trough. The movable barrier is used to push tire molecules on tire subphase togetlier in tire Langmuir film which is subsequently transferred to a solid substrate.

A drop of a dilute solution (1%) of an amphiphile in a solvent is typically placed on tlie water surface. The solvent evaporates, leaving behind a monolayer of molecules, which can be described as a two-dimensional gas, due to tlie large separation between tlie molecules (figure C2.4.3). The movable barrier pushes tlie molecules at tlie surface closer together, while pressure and area per molecule are recorded. The pressure-area isotlienn yields infonnation about tlie stability of monolayers at tlie water surface, a possible reorientation of tlie molecules in tlie two-dimensional system, phase transitions and changes in tlie confonnation. Wliile being pushed togetlier, tlie layer at... 

In the case of chemisoriDtion this is the most exothennic process and the strong molecule substrate interaction results in an anchoring of the headgroup at a certain surface site via a chemical bond. This bond can be covalent, covalent with a polar part or purely ionic. As a result of the exothennic interaction between the headgroup and the substrate, the molecules try to occupy each available surface site. Molecules that are already at the surface are pushed together during this process. Therefore, even for chemisorbed species, a certain surface mobility has to be anticipated before the molecules finally anchor. Otherwise the evolution of ordered stmctures could not be explained. 

Figure C3.1.2. Stopped-flow apparatus with motor-driven syringes. Syringe plungers force tire reactants A and B tlirough a mixing chamber into a spectral cell. Kinetic data collection begins when tire effluent syringe plunger is pushed out to contact an activation switch, about a millisecond after tire initiation of mixing. (Adapted from Pilling M J and Seakins P W 1995 Reaction Kinetics (Oxford Oxford University Press)...

Figure 2.8. The iwo orbitals overlap giving a covalent bond and ihe tvvv electrons are (>ir in a molecular orbital. (If the t o nuclei could be pushed together completely, the...

Phosphorus pentachloride is prepared by the action of chlorine on phosphorus trichloride. To push the equilibrium over to the right, the temperature must be kept low and excess chlorine must be present. Hence the liquid phosphorus trichloride is run dropwise into a flask cooled in ice through which a steady stream of dry chlorine is passed the solid pentachloride deposits at the bottom of the flask. 

The previous application — in accord with most MD studies — illustrates the urgent need to further push the limits of MD simulations set by todays computer technology in order to bridge time scale gaps between theory and either experiments or biochemical processes. The latter often involve conformational motions of proteins, which typically occur at the microsecond to millisecond range. Prominent examples for functionally relevant conformatiotial motions... 

As many different file formats have been developed since the early 1970s, the need for a standard chemical structure format has been increasingly felt. Various attempts have been made by different groups of the chemical commimity to define and push such a format, but none has achieved unanimous acceptance. 

Waals radius r] " (or each uom lype and a hardness pararn clcr t lh U determines ihe depth of the attractive well and how easy (or difficult) it is to push atom s close togeth er. fhere are in teraction s for each n on hori ded ij paii, in cliidin g all I 4 pairs. I hc parameters for a pair are obtained from individual alorn parameters as follows ... 

---