Leave-behind

A drop of a dilute solution (1%) of an amphiphile in a solvent is typically placed on tlie water surface. The solvent evaporates, leaving behind a monolayer of molecules, which can be described as a two-dimensional gas, due to tlie large separation between tlie molecules (figure C2.4.3). The movable barrier pushes tlie molecules at tlie surface closer together, while pressure and area per molecule are recorded. The pressure-area isotlienn yields infonnation about tlie stability of monolayers at tlie water surface, a possible reorientation of tlie molecules in tlie two-dimensional system, phase transitions and changes in tlie confonnation. Wliile being pushed togetlier, tlie layer at... 

Before this treatment, the cassiterite content of the ore is increased by removing impurities such as clay, by washing and by roasting which drives off oxides of arsenic and sulphur. The crude tin obtained is often contaminated with iron and other metals. It is, therefore, remelted on an inclined hearth the easily fusible tin melts away, leaving behind the less fusible impurities. The molten tin is finally stirred to bring it into intimate contact with air. Any remaining metal impurities are thereby oxidised to form a scum tin dross ) on the surface and this can be skimmed off Very pure tin can be obtained by zone refining. 

Now remove the flask from the water-bath, and slowly add a solution of 5 ml. (5-2 g.) of dry ethyl benzoate in 15 ml. of anhydrous ether down the condenser in small quantities at a time, mixing the contents of the flask thoroughly between each addition. When the boiling of the ether again subsides, return the flask to the water-bath and reheat for a further 15 minutes. Then cool the mixture in ice-water, and carefully pour off the ethereal solution into a mixture of about 60 ml. of dilute sulphuric acid. and 100 g. of crushed ice contained in a flask of about 500 ml. capacity fitted for stearn-distillation, taking care to leave behind any unchanged magnesium. 

R NHa + C.HjNCO = RNH CO NHC,Hj Traces of water will contaminate the product with diphenylurea (p. 336) if the solution is boiled hence the need for anhydrous conditions. i-Naphthylisocyanate reacts more slowly with water, and the i-naphthyl-urea derivative can often be obtained using a cold aqueous solution of an aliphatic amine it is particularly necessary in such cases to purify the product by recrystallisation from, or extraction with, boiling petroleum, leaving behind any insoluble di i-naphthylurea. Note that the amine must also be free from alcohols (p. 335) and phenols (p. 337). 

The goal of an analytical separation is to remove either the analyte or the interferent from the sample matrix. To achieve a separation there must be at least one significant difference between the chemical or physical properties of the analyte and interferent. Relying on chemical or physical properties, however, presents a fundamental problem—a separation also requires selectivity. A separation that completely removes an interferent may result in the partial loss of analyte. Altering the separation to minimize the loss of analyte, however, may leave behind some of the interferent. 

Aerosols can be produced as a spray of droplets by various means. A good example of a nebulizer is the common household hair spray, which produces fine droplets of a solution of hair lacquer by using a gas to blow the lacquer solution through a fine nozzle so that it emerges as a spray of small droplets. In use, the droplets strike the hair and settle, and the solvent evaporates to leave behind the nonvolatile lacquer. For mass spectrometry, a spray of a solution of analyte can be produced similarly or by a wide variety of other methods, many of which are discussed here. Chapters 8 ( Electrospray Ionization ) and 11 ( Thermospray and Plasmaspray Interfaces ) also contain details of droplet evaporation and formation of ions that are relevant to the discussion in this chapter. Aerosols are also produced by laser ablation for more information on this topic, see Chapters 17 and 18. 

In the earliest interface, a continuous moving belt (loop) was used onto which the liquid emerging from the chromatographic column was placed as a succession of drops. As the belt moved along, the drops were heated at a low temperature to evaporate the solvent and leave behind any mixture components. Finally, the dried components were carried into the ion source, where they were heated strongly to volatilize them, after which they were ionized. 

An emulsion system in which the propellant is in the external or continuous phase is shown in Figure 2b. As the Hquefied propellant vaporizes, it escapes direcdy into the atmosphere, leaving behind droplets of the formulation which are emitted as a wet spray. This system is typical of many water-based aerosols or w/o emulsions. 

Sprays. Aerosol spray emulsions are of the water-in-oil type. The preferred propellant is a hydrocarbon or mixed hydrocarbon—hydrofluorocarbon. About 25 to 30% propellent, miscible with the oil, remains in the external phase of the emulsion. When this system is dispensed, the propellant vaporizes, leaving behind droplets of the w/o emulsion (Fig. 2b). A vapor tap valve, which tends to produce finely dispersed particles, is employed. Because the propellant and the product concentrate tend to separate on standing, products formulated using this system, such as pesticides and room deodorants, must be shaken before use. 

Any material which can form a color center contains two types of precursors as shown in Figure 2a. The hole center precursor is an atom, ion, molecule, impurity, or other defect which contains two paired electrons, one of which can be ejected by irradiation, leaving behind a hole center (Fig. 2b). The electron center precursor is an atom, ion, etc, which can produce an electron center by trapping the electron ejected from the hole center precursor. A hole and an electron center are thus formed simultaneously. Either or both can be the color center. Almost all materials have hole center precursors. If there is no electron center precursor, however, the displaced electron returns to its original place and the material remains unchanged. 

Selenium and precious metals can be removed selectively from the chlorination Hquor by reduction with sulfur dioxide. However, conditions of acidity, temperature, and a rate of reduction must be carefliUy controlled to avoid the formation of selenium monochloride, which reacts with elemental selenium already generated to form a tar-like substance. This tar gradually hardens to form an intractable mass which must be chipped from the reactor. Under proper conditions of precipitation, a selenium/precious metals product substantially free of other impurities can be obtained. Selenium can be recovered in a pure state by vacuum distillation, leaving behind a precious metals residue. 

A number of dielectric films are deposited by the spin-on technique. In this case the film s constituent molecules are dissolved in a solvent to form a hquid. After spinning the Hquid over a semiconductor surface the solvent is driven off with a baking step, leaving behind the thin dielectric film. Common films include polyimide and benzocyclobutene (BCB). The deposition process for these films is simple, making it attractive for a manufacturing process. 

---