Distinguishable

In ternary systems, we distinguish between two common types. In type II, two binaries are partially miscible and the third binary is completely miscible in type I, only one binary is partially miscible. (A third type, where all three binaries are only partially miscible, is relatively rare and not considered here.)... 

By considering only those raw materials which undergo reaction to undesired byproduct, only the raw materials costs which are in principle avoidable are considered. Those raw materials costs which are inevitable (i.e., the stoichiometric requirements for FEED which converts into the desired PRODUCT) are not included. Raw materials costs which are in principle avoidable are distinguished from those which are inevitable from the stoichiometric requirements of the reaction. ... 

Molisch s test A general test for carbohydrates. The carbohydrate is dissolved in water, alcoholic 1-naphthol added, and concentrated sulphuric acid poured down the side of the tube. A deep violet ring is formed at the junction of the liquids. A modification, the rapid furfural test , is used to distinguish between glucose and fructose. A mixture of the sugar, 1-naphthol, and concentrated hydrochloric acid is boiled. With fructose and saccharides containing fructose a violet colour is produced immediately the solution boils. With glucose the appearance of the colour is slower. 

One distinguishes preparatory distillations that are designed to separate the fractions for subsequent analysis from non-preparatory analytical distillations that are performed to characterize the feed itself. For example, the distillation curve that gives the recovered volume or weight as a function of the distillation temperature characterizes the volatility of the sample. 

It is clear that these gases have widely varying compositions according to the processes used, but refinery gas is distinguished from natural gases by the presence of hydrogen, mono- and diolefins, and even acetylenes. 

Identification of normal paraffins by chromatography presents no special problems with the exception of biodegraded crudes, they are clearly distinguished. The problem encountered is to quantify, as shown in Figure 3.14, the normal paraffin peaks that are superimposed on a background representing other hydrocarbons. 

Liquid chromatography is preceded by a precipitation of the asphaltenes, then the maltenes are subjected to chromatography. Although the separation between saturated hydrocarbons and aromatics presents very few problems, this is not the case with the separation between aromatics and resins. In fact, resins themselves are very aromatic and are distinguished more by their high heteroatom content (this justifies the terms, polar compounds or N, S, 0 compounds , also used to designate resins). 

Characteristics are the experimental data necessary for calculating the physical properties of pure components and their mixtures. We shall distinguish several categories ... 

Liquid viscosity is one of the most difficult properties to calculate with accuracy, yet it has an important role in the calculation of heat transfer coefficients and pressure drop. No single method is satisfactory for all temperature and viscosity ranges. We will distinguish three cases for pure hydrocarbons and petroleum fractions ... 

Thermal conductivity is expressed in W/(m K) and measures the ease in which heat is transmitted through a thin layer of material. Conductivity of liquids, written as A, decreases in an essentially linear manner between the triple point and the boiling point temperatures. Beyond a reduced temperature of 0.8, the relationship is not at all linear. For estimation of conductivity we will distinguish two cases < )... 

We will give here just the main distinguishing characteristics of home heating oil with respect to diesel fuel. 

In France there are four categories of heavy fuels whose specifications are given in Table 5.19 the different product qualities are distinguished essentially by the viscosity, equal to or less than 110 mm /s at SOT for No. 1 fuel oil, equal to or greater than 110 mm /s for No. 2 fuel oil, and by the sulfur content varying from 4 wt. % (No. 2 fuel oil) to 1 wt. % (No. 2 TBTS - very low sulfur content fuel oil). 

Non-fuel petroleum products cover an extremely wide range and are distinguished as much by their nature and physical aspects as by their types of application. 

The properties sought for these products depend on the type of application it is useful to distinguish motor oil from industrial lubricants. 

The standard NF T 65-004 classifies the types of composite bitumen it distinguishes three grades of bitumen-tars by their pseudo-viscosities and two grades of bitumen-coal tar pitch by their penetrabilities. 

The standard NF T 65-011 distinguishes the bitumen emulsions by their ionic nature (anionic or cationic), their stability with respect to agglomerates and weight content of base binder. There are 20 grades of emulsions. 

Moreover, it is useful to distinguish between the standards prepared by the official standards organizations and the professional standards. The former s mission is to ensure that the conditions of the consensus of the widest assemblage of interested parties are followed. The professional standards are prepared by recognized professional organizations but limit the consensus to only the participating organizations. 

Specifications and test methods for heavy fuel oil (in France, FOL). The French specifications distinguish two grades FOL No. 1 and the heavier ... 

One can distinguish three important additive classes according to their modes of action ... 

These are the major processes in refining and petrochemicals. In this large group of processes, the following are distinguished ... 

To type crude oils (see Figure 2.13). This method uses an extremely accurate compositional analysis of crudes to determine their source and possible migration route. As a result of the accuracy It is possible to distinguish not only the oils of individual accumulations in a region, but even the oils from the different drainage units within a field. If sufficient samples were taken at the exploration phase of a field, geochemistry allows one to verify cross flow and preferential depletion of units during later production. 

The experiment could be repeated at a number of different temperatures and initial pressures to determine the shape of the two-phase envelope defined by the bubble point line and the dew point line. These two lines meet at the critical point, where it is no longer possible to distinguish between a compressed gas and a liquid. 

In this example it would therefore be justifiable to spend up to 22 million on appraisal activity which would distinguish between the high, medium, and low STOMP cases. If it would cost more than 22 million to determine this, then it would be better to go ahead without the appraisal. The decision tree has therefore been used to place a value on the appraisal activity, and to indicate when it is no longer worthwhile to appraise. 

The previous section showed that the fluids present in the reservoir, their compressibilities, and the reservoir pressure all determine the amount of energy stored in the system. Three sets of initial conditions can be distinguished, and reservoir and production behaviour may be characterised in each case ... 

The other main physical property of gas which distinguishes it from oil is its compressibility the fractional change in volume (V) per unit of change in pressure (P) at constant temperature (T). Recall that... 

However curves summing all measured levels may a bit conceal some weighty information about course of damaging. From this reason it is necessary to pay attention even detail analysis of individual measured levels. Example of distinguishable number of counts and record of counts fiequency in all levels summing curve in comparison with same records in some selected levels shows the Fig.7. 

When implementing CBR systems one has to able to define and implement the methods to distinguish between data from different classes. This is a more difficult problem than when constructing a simple data classifier, as the important parameters cannot be simply determined based on a set of examples. One has to have some a-priori knowledge about the important features that distinguish various data classes, as well as anticipate possible data forms that can be encountered during future inspections. This may necessitate the use of more features to describe the problem than a comparable classifier would use. When determining the data... 

The recognition ratios achieved by CBR systems developed as part of this project could not be bettered by either neural-network classifiers or rule-based expert system classifiers. In addition, CBR systems should be mote reliable than simple classifiers as they are programmed to recognise unknown data. The knowledge acquisition necessary to build CBR systems is less expensive than for expert systems, because it is simpler to describe the knowledge how to distinguish between certain types of data than to describe the whole data contents. 

Braun and Hauck [3] discovered that the irrotational and solenoidal components of a 2-D vector field can be imaged separately using the transverse and longitudinal measurements, respectively. This result has a clear analogy in a 2-D tensor field. We can distinguish three types of measurements which determine potentials of the symmetric tensor field separately ... 

The curve is symmetric from the middle of the slot. Hence the length of the defect is determined by the position of its edges at (x2+x3)/2 and -(x2+x3)/2 in the scanning direction of the probe. Of course this result is only true if we can distinguish the 5 zones on the curve. For other relative dimensions, for example a slot smaller than the probe (outer diameter), a curve like in set 1 is obtained, where the zones are confused. 

---