Base solvent

This procedure has been performed in a variety of ways [28 p714, 38-42] with variations in solvent, base and time of reaction. For piperonal conversion, the consensus is toward the use of acetic acid as the solvent, ammonium acetate as the base and 4 hours of reflux time. Dr. Alexander Shulgin, a giant in this field, prefers the use of cyclohexylamine as the base. Strike would not tend to doubt this man s choice, especially since Strike is also getting the... 

Acids that are better proton donors than the solvent are leveled to the acid strength of the protonated solvent bases that are better proton acceptors than the solvent are leveled to the base strength of the deprotonated solvent. 

Another widely used overlay adhesive is the contact type. These specialized adhesives, in the same group as mbber cement, may be of the solvent-base or water-base types. They are often used to bond overlays such as wood veneer, vinyl (poly(vinyl chloride)) films, or high pressure laminates such as countertop overlays. 

Cellulosics. CeUulosic adhesives are obtained by modification of cellulose [9004-34-6] (qv) which comes from cotton linters and wood pulp. Cellulose can be nitrated to provide cellulose nitrate [9004-70-0] which is soluble in organic solvents. When cellulose nitrate is dissolved in amyl acetate [628-63-7] for example, a general purpose solvent-based adhesive which is both waterproof and flexible is formed. Cellulose esterification leads to materials such as cellulose acetate [9004-35-7], which has been used as a pressure-sensitive adhesive tape backing. Cellulose can also be ethoxylated, providing hydroxyethylceUulose which is useful as a thickening agent for poly(vinyl acetate) emulsion adhesives. Etherification leads to materials such as methylceUulose [9004-67-5] which are soluble in water and can be modified with glyceral [56-81-5] to produce adhesives used as wallpaper paste (see Cellulose esters Cellulose ethers). 

Free mono- and multilayer films may be adhesive- or extmsion-bonded in the laminating process. The bonding adhesive may be water- or solvent-based. Alternatively, a temperature-dependent polymer-based adhesive without solvent may be heated and set by cooling. In extmsion lamination, a film of a thermoplastic such as polyethylene is extmded as a bond between the two flat materials, which are brought together between a chilled and backup roU. 

The inks formulated for jet printing must be very fluid, stable, and free of any particles that could cause clogging of the jet nozzles, and be capable of depositing and adhering to a substrate with a minimum of character fogging. They are generally formulated with soluble dye colorants in a suitable aqueous or solvent-based vehicle (9). 

MEK is also used iu solvent-based adhesives, iu printing ink formulations, as a solvent iu magnetic tape manufacture, and is the most common solvent used iu dewaxing lubricating oils. Of all these appHcations only an increasing consumption of magnetic tapes is likely to grow ia methyl ethyl ketone use. 

For example, Day-Glo HM Series toners come ia a range of colors suitable for flexographic and gravure inks of the solvent-base type. The Radiant GF Series and Lawter HVT Series are also suitable for this type of apphcation (see Table 2). Generally, these toners are of the formaldehyde—sulfonamide type and requite oxygenated solvents, primarily alcohol—ester blends, for proper solution. For appHcations such as flexographic printing on film, these materials are modified with other resias such as nitrocellulose or polyamides ia the finished ink. 

Recovery and Purification. AH processes for the recovery and refining of maleic anhydride must deal with the efficient separation of maleic anhydride from the large amount of water produced in the reaction process. Recovery systems can be separated into two general categories aqueous- and nonaqueous-based absorption systems. Solvent-based systems have a higher recovery of maleic anhydride and are more energy efficient than water-based systems. 

Cleaning, the removal of unwanted matter, is the beginning of the treatment cycle for metal. The unwanted matter may be carbon smut, welding flux, ink, oxidation products, oil, fingerprints, or other material. Cleaners may be classified as solvent-based or aqueous. Within the aqueous class there are many subclasses, the most important of which are the alkaline cleaners. There are also a variety of ways to apply cleaners. As of the mid-1990s, solvent-based cleaner usage is declining. 

Mineral spirits, a type of petroleum distillate popular for use in solvent-based house paints, consist mainly of aUphatic hydrocarbons with a trace of aromatics. This type of solvent finds use in oil- and alkyd-based house paints because of its good solvency with typical house paint binders and its relatively slow evaporation rate which imparts good bmshabiUty, open-time, and leveling. Other properties include lower odor, relatively lower cost, as well as safety and health hazard characteristics comparable to most other organic solvents. 

Paint Formulations. Tables 1 and 2 provide examples of generic water-based latex and solvent-based alkyd oil paints. These formulations exhibit typical proportions of the paint ingredients discussed. 

Table 2. Exterior Alkyd-Linseed Oil Flat Solvent-Based House Paint ...

For the most part, additives control the appHcation or theological properties of a paint. These additives include materials for latex paints such as hydroxyethylceUulose, hydrophobicaHy modified alkah-soluble emulsions, and hydrophobicaHy modified ethylene oxide urethanes. Solvent-based alkyd paints typically use castor oil derivatives and attapulgite and bentonite clays. The volume soHds of a paint is an equally important physical property affecting the apphcation and theological properties. Without adequate volume soHds, the desired appHcation and theological properties may be impossible to achieve, no matter how much or many additives are incorporated into the paint. 

Adhesives. Contact adhesives are blends of mbber, phenoHc resin, and additives suppHed in solvent or aqueous dispersion form they are typically appHed to both surfaces to be joined (80). Evaporation of the solvent leaves an adhesive film that forms a strong, peel-resistant bond. Contact adhesives are used widely in the furniture and constmction industries and also in the automotive and footwear industries. The phenoHc resins promote adhesion and act as tackifiers, usually at a concentration of 20—40%. In solvent-based contact adhesives, neoprene is preferred, whereas nitrile is used in specialty appHcations. The type and grade of phenoHc resin selected control tack time, bond strength, and durabiHty. 

Bonding properties of water-based contact adhesives are similar to those of solvent-based systems, but are free of flammabihty ha2ards. However, drying times are longer and the bond is sensitive to moisture. 

Car poHshes can be soHd, semisoHd, or Hquid. They can be solvent-based or emulsions. In either case, Hquid and soHd forms are possible. Compdations of suggested formulas are given in References 3, 12, and 44. A representative Hquid emulsion product may contain 10—15 wt % abrasive,... 

---