Solvent-based paints

Mineral spirits, a type of petroleum distillate popular for use in solvent-based house paints, consist mainly of aUphatic hydrocarbons with a trace of aromatics. This type of solvent finds use in oil- and alkyd-based house paints because of its good solvency with typical house paint binders and its relatively slow evaporation rate which imparts good bmshabiUty, open-time, and leveling. Other properties include lower odor, relatively lower cost, as well as safety and health hazard characteristics comparable to most other organic solvents. 

Paint Formulations. Tables 1 and 2 provide examples of generic water-based latex and solvent-based alkyd oil paints. These formulations exhibit typical proportions of the paint ingredients discussed. 

Table 2. Exterior Alkyd-Linseed Oil Flat Solvent-Based House Paint ...

For the most part, additives control the appHcation or theological properties of a paint. These additives include materials for latex paints such as hydroxyethylceUulose, hydrophobicaHy modified alkah-soluble emulsions, and hydrophobicaHy modified ethylene oxide urethanes. Solvent-based alkyd paints typically use castor oil derivatives and attapulgite and bentonite clays. The volume soHds of a paint is an equally important physical property affecting the apphcation and theological properties. Without adequate volume soHds, the desired appHcation and theological properties may be impossible to achieve, no matter how much or many additives are incorporated into the paint. 

These pigments are sensitive to heat and bleed ia most paint solvents. They are, however, resistant to acids and bases. Their tinctorial strength is considerably greater than that of inorganic yellows but they are weaker than the diaryUde yellows. They are used extensively ia emulsion paints, paper coating compositions, inks (qv), and, depending on particle size, can ia some cases be used outdoors because of excellent lightfastness ia full shades. 

In many cases, the inherent safety advantages of one process are clear when compared with alternatives. One or more hazards may be significantly reduced, while others are unaffected or only marginally increased. For example, aqueous latex paints are clearly inherently safer than solvent based paints, although there are applications where the increased performance of solvent based paints justifies their use, with the appropriate layers of protection. 

Water based paints and adhesives, replacing solvent based products... 

These methods are generally appropriate for either thin-film solvent-based paints or for coatings up to about 150 /xm thickness. The techniques are more usually used for the priming layer of the coating systems. 

The fact that very low concentrations of polymer give highly viscous solutions is exploited commercially in a number of applications. The thickening action of polymers is often necessary for water-based substances, such as foods, toothpastes, or emulsion paints, but examples also occur of the use of polymers to thicken solvent-based products, such as paint stripper. 

Installation of a water-based electrostatic immersion painting system to replace a solvent-based painting system. The water-based system resulted in a waste solvent reduction of more than 95%. 

The first paints were based upon linseed oil (obtained from flax). This is an unsaturated long-chain triglyceride, which, with metal activators, crosslinks via radical pathways to form a continuous film on the substrate. Modern paints use synthetic polymers together with either a solvent or suspending medium (e.g., water), which evaporates leaving the deposited film. Exceptions are powder coatings, which require heat for completion. 

These are the most important components of paint. Coatings can be either clear or opaque (containing pigments) and either solvent- or water-based. With solvent-based paints, after application, most of the solvent is lost through evaporation. These solvent-based coatings are mostly alkyds (name derived from alkyl/acid) or modified alkyd resins. Normally they contain 30% polymer solids higher solids content is limited by the increasing viscosity of the system. 

The spray paint can was inverted and a small amount of product was dispensed into a 20 mL glass headspace vial. The vial was immediately sealed and was incubated at 80°C for approximately 30 min. After this isothermal hold, a 0.5-mL portion of the headspace was injected into the GC/MS system. The GC-MS total ion chromatogram of the paint solvent mixture headspace is shown in Figure 15. Numerous solvent peaks were detected and identified via mass spectral library searching. The retention times, approximate percentages, and tentative identifications are shown in Table 8 for the solvent peaks. These peak identifications are considered tentative, as they are based solely on the library search. The mass spectral library search is often unable to differentiate with a high degree of confidence between positional isomers of branched aliphatic hydrocarbons or cycloaliphatic hydrocarbons. Therefore, the peak identifications in Table 8 may not be correct in all cases as to the exact isomer present (e.g., 1,2,3-cyclohexane versus 1,2,4-cyclohexane). However, the class of compound (cyclic versus branched versus linear aliphatic) and the total number of carbon atoms in the molecule should be correct for the majority of peaks. 

There are a number of other media which are also pigmented with P.V.23. The list includes office articles and artists colors, such as drawing inks and fiber-tip pen inks, wax crayons, oil paints, and high quality water colors, water- or solvent-based pigmented wood stains, cleaning agents, and mass colored paper. 

Class B Flammable liquids Fires in flammable liquids, combustible liquids, petroleum greases, tars, oils, oil-based paints, solvents, lacquers, alcohols, and flammable gases. 

Substrates, Paints and Coatings. Both flash rusting and underfilm darkening studies exployed a white, pH 4.5, primer formulation (see Appendix), designated as Standard, based upon Haloflex 202, a chlorine-containing vinyl acrylic latex. A zinc phosphate free formulation, designated as Non-Standard, of pH6 was prepared by substitution of zinc phosphate for barytes. The comparison paints were a commercial butyl acrylate-methyl methacrylate water borne primer, formulated at pH 9, and a solvent based chlorinated rubber primer. 

S Solvents Except for the direct use of CH2CI2 in equipment cleanup, most paint strippers sold are formulated products. Solvent-based strippers commonly employ a number of components that each accomplish a given task or function. The first component is a primary solvent that serves to penetrate the paint film and promote swelling. Cosolvents may also be used to increase the rate of penetration and to keep the varions components from separating. 

Republic Container Co. (Nitro, West Va.), a company that supplies steel drums, switched from a solvent-based paint to a water-based paint, reducing their VOC emissions to 2.8 Ib/gal and saving over 10,000 in costs. 

---