Purity of analyte

Procedure. To obtain experience in the method, the purity of analytical-grade potassium chlorate may be determined. Prepare a 0.02M potassium chlorate solution. Into a 250 mL conical flask, place 25.0 mL of the potassium chlorate solution, 25.0mL of 0.2M ammonium iron(II) sulphate solution in 2M sulphuric acid and add cautiously 12 mL concentrated sulphuric acid. Heat the mixture to boiling (in order to ensure completion of the reduction), and cool to room temperature by placing the flask in running tap water. Add 20 mL 1 1 water/phosphoric(V) acid, followed by 0.5 mL sodium diphenyl-amine-sulphonate indicator. Titrate the excess Fe2+ ion with standard 0.02M potassium dichromate to a first tinge of purple coloration which remains on stirring. 

The most discriminating technique for proving the identity and purity of analyte peak of a chromatogram, especially for analyzing biological samples and natural products, is by using online LC-UV/MS or GC-MS/FTIR methods [15]. Alternatively, one could use a combination of TLC and MS, where direct determination on the TLC plates is made by matrix-assisted laser desorption ionization mass spectrometry (MALDI MS) [16]. 

In other words, the purity of analyte and IS reference standards determines the maximum possible concentration span. Sometimes, it is impossible to simultaneously satisfy both (1) and (2), i.e C >C In this case, either calibration range needs to be adjusted (narrowed) or analyte or internal standard reference standards of higher purity must be used. 

Inclusions are a frequent source of trouble in industrial crystallization. Crystals grown from aqueous solution can contain up to 0.5% by mass of liquid inclusions, and their presence can significantly affect the purity of analytical reagents, pharmaceutical chemicals and foodstuffs such as sugar. Inclusions can cause caking (section 7.6) of stored crystals by the seepage of liquid if the crystals become broken. 

Here Xj-x represent measured quantities including physical ones (e.g., mass of analytical standard weighed out, volumes of standard flasks etc.) and chemical properties (e.g., chemical purity of analytical standard, isotopic purity of an internal standard, ratios of analytical signals for analyte and internal standard etc.). Specific examples of such functions are those discussed in Section 8.4. The experimental variables (x(m+])-x ) that do not appear directly in the functional relationship could include temperature of various components of all forms of apparatus used, mobile phase composition and flow rate, operating parameters of the mass spectrometer, etc. 

Stem layer adsorption was involved in the discussion of the effect of ions on f potentials (Section V-6), electrocapillary behavior (Section V-7), and electrode potentials (Section V-8) and enters into the effect of electrolytes on charged monolayers (Section XV-6). More speciflcally, this type of behavior occurs in the adsorption of electrolytes by ionic crystals. A large amount of wotk of this type has been done, partly because of the importance of such effects on the purity of precipitates of analytical interest and partly because of the role of such adsorption in coagulation and other colloid chemical processes. Early studies include those by Weiser [157], by Paneth, Hahn, and Fajans [158], and by Kolthoff and co-workers [159], A recent calorimetric study of proton adsorption by Lyklema and co-workers [160] supports a new thermodynamic analysis of double-layer formation. A recent example of this is found in a study... 

Standard EDTA Solutions. Disodium dihydrogen ethylenediaminetetraacetate dihydrate is available commercially of analytical reagent purity. After drying at 80°C for at least 24 hr, its composition agrees exactly with the dihydrate formula (molecular weight 372.25). It may be weighed directly. If an additional check on the concentration is required, it may be standardized by titration with nearly neutralized zinc chloride or zinc sulfate solution. 

Let s use a simple example to develop the rationale behind a one-way ANOVA calculation. The data in Table 14.7 show the results obtained by several analysts in determining the purity of a single pharmaceutical preparation of sulfanilamide. Each column in this table lists the results obtained by an individual analyst. For convenience, entries in the table are represented by the symbol where i identifies the analyst and j indicates the replicate number thus 3 5 is the fifth replicate for the third analyst (and is equal to 94.24%). The variability in the results shown in Table 14.7 arises from two sources indeterminate errors associated with the analytical procedure that are experienced equally by all analysts, and systematic or determinate errors introduced by the analysts. 

Analysis of Standards The analysis of a standard containing a known concentration of analyte also can be used to monitor a system s state of statistical control. Ideally, a standard reference material (SRM) should be used, provided that the matrix of the SRM is similar to that of the samples being analyzed. A variety of appropriate SRMs are available from the National Institute of Standards and Technology (NIST). If a suitable SRM is not available, then an independently prepared synthetic sample can be used if it is prepared from reagents of known purity. At a minimum, a standardization of the method is verified by periodically analyzing one of the calibration standards. In all cases, the analyte s experimentally determined concentration in the standard must fall within predetermined limits if the system is to be considered under statistical control. 

Because the higher alcohols are made by a number of processes and from different raw materials, analytical procedures are designed to yield three kinds of information the carbon chain length distribution, or combining weight, of the alcohols present the purity of the material and the presence of minor impurities and contaminants that would interfere with subsequent use of the product. Analytical methods and characterization of alcohols have been summarized (13). 

Specifications and Standards, Shipping. Commercial iodine has a minimum purity of 99.8%. The Committee of Analytical reagents of the American Chemical Society (67) and the U.S. Pharmacopoeia XXII (68) specify an iodine content not less than 99.8%, a maximum nonvolatile residue of 0.01%, and chlorine—bromine (expressed as chlorine) of 0.005% (ACS) and 0.028% (USP), respectively. In the past these requirements were attained basicaHy only by sublimation, but with processing changes these specifications can be met by direct production of iodine. Previously the impurities of the Chilean product were chiefly water, sulfuric acid, and insoluble materials. Improvements in the production process, and especiaHy in the refining step, aHow the direct obtainment of ACS-type iodine. Also, because of its origin and production process, the Chilean iodine has a chlorine—bromine impurity level of no more than 0.002%. 

Analytical and Test Methods. o-Nitrotoluene can be analyzed for purity and isomer content by infrared spectroscopy with an accuracy of about 1%. -Nitrotoluene content can be estimated by the decomposition of the isomeric toluene diazonium chlorides because the ortho and meta isomers decompose more readily than the para isomer. A colorimetric method for determining the content of the various isomers is based on the color which forms when the mononitrotoluenes are dissolved in sulfuric acid (45). From the absorption of the sulfuric acid solution at 436 and 305 nm, the ortho and para isomer content can be deterrnined, and the meta isomer can be obtained by difference. However, this and other colorimetric methods are subject to possible interferences from other aromatic nitro compounds. A titrimetric method, based on the reduction of the nitro group with titanium(III) sulfate or chloride, can be used to determine mononitrotoluenes (32). Chromatographic methods, eg, gas chromatography or high pressure Hquid chromatography, are well suited for the deterrnination of mononitrotoluenes as well as its individual isomers. Freezing points are used commonly as indicators of purity of the various isomers. 

Integration of the peaks for the two diastereomers accurately quantifies the relative amounts of each enantiomer within the mixture. Such diastereometic derivatives may also be analy2ed by more accurate methods such as gc or hplc. One drawback to diastereometic detivatization is that it requites at least 15 mg of material, which is likely to be material painstakingly synthesized, isolated, and purified. The use of analytical chiral chromatographic methods allows for the direct quantification of enantiomeric purity, is highly accurate to above 99.8% ee, and requites less than one milligram of material. 

Specifications and Analytical Methods. The purity of 2-pyrrohdinone is determined by gas chromatography and is specified as 98.5 wt % minimum. Maximum moisture content is specified as 0.5 wt %. Typical purities are much higher than specification. 

Purity of toluene samples as well as the number, concentration, and identity of other components can be readily determined using standard gas chromatography techniques (40—42). Toluene content of high purity samples can also be accurately measured by freezing point, as outlined in ASTM D1016. Toluene exhibits characteristic uv, it, nmr, and mass spectra, which are useful in many specific control and analytical problems (2,43—45). 

Ethylene oxide is sold as a high purity chemical, with typical specifications shown ia Table 14. This purity is so high that only impurities are specified. There is normally no assay specification. Proper sampling techniques are critical to avoid personal exposure and prevent contamination of the sample with trace levels of water. A complete review and description of analytical methods for pure ethylene oxide is given ia Reference 228. 

The acid is analytically pure. There is no satisfactory solvent for the recrystallization of large amounts of terephthalic acid. Small quantities may be recrystaUized from acetic acid, but the purity of a properly precipitated and washed sample is not thereby improved. 

Although this material is suitable for most purposes, it may be purified further in the following manner. It is dissolved by heating in a solution of 2 g. of stannous chloride and 2 cc. of concentrated hydrochloric acid in i 1. of water, and the hot solution is clarified by filtration through a 5-mm. mat of decolorizing carbon (Note g). The yellow or red color which may develop disappears on reheating to the boiling point. After the addition of 100 cc. of concentrated hydrochloric acid the solution is allowed to cool in an ice bath, treated with a second roo cc. of acid, cooled to 0°, and collected and washed as befor The ciystalline product is colorless, ash-free, and of analytical purity. The loss in the crystallization of an 80-g. lot amounts to 5-10 g. (6-12 per cent). 

Acylation of various oxygen functions by use of common and commercially available fluonnated carboxylic acid denvatives such as trifluoroacetic anhydride or the corresponding acyl halides have already been discussed sufficiently in the first edition [10] Therefore only exceptional observations will be described in this section In the past 15 years, many denvatizations of various nonfluonnated oxygen compounds by fluoroacylation were made for analytical purposes. Thus Mosher s acid chlorides for example became ready-to-use reagents for the determination of the enantiomeric purity of alcohols and amines by NMR or gas-liquid chromatographic (GLC) techniques [//] (equation 1)... 

In general, the analysis of essential oils merely involves the application of the ordinary principles of analytical chemistry to this special group of bodies, which possess many features in common. Of course, many special processes have to be used in certain cases, to which attention will be drawn where necessary. The present chapter will be devoted to the details of a few methods which are in very common use in the analysis of these bodies, and which are absolutely necessary in order to form an opinion on the purity of very many oils. Particular processes are mentioned as required under the essential oils or compounds concerned. These remarks may be prefaced by saying that the obtaining of the results of an analysis of an essential oil is not always as difficult a matter as the interpretation of the same when obtained. 

If there is any doubt as to the purity of the reagents used, they should be tested by standard methods for the impurities that might cause errors in the determinations. It may be mentioned that not all chemicals employed in quantitative analysis are available in the form of analytical reagents the purest commercially available products should, if necessary, be purified by known methods see below. The exact mode of drying, if required, will vary with the reagent details are given for specific reagents in the text. 

A. Benzoic acid (C6H5COOH R.M.M. = 122.12). Analytical grade material has a purity of at least 99.9 per cent. For work demanding the highest accuracy, the acid should be dried before use by careful fusion in a platinum crucible placed in an oven at about 130°C, and then powdered in an agate mortar. 

Method A With arsenic(III) oxide. This procedure, which utilises arsenic(III) oxide as a primary standard and potassium iodide or potassium iodate as a catalyst for the reaction, is convenient in practice and is a trustworthy method for the standardisation of permanganate solutions. Analytical grade arsenic(III) oxide has a purity of at least 99.8 per cent, and the results by this method agree to within 1 part in 3000 with the sodium oxalate procedure (Method B, below). 

Analytical grade potassium dichromate has a purity of not less than 99.9 per... 

For practice, determine the percentage of N02 in potassium nitrite, or the purity of sodium nitrite, preferably of analytical-grade quality. 

Thermogravimetry is a valuable technique for the assessment of the purity of materials. Analytical reagents, especially those used in titrimetric analysis as primary standards, e.g. sodium carbonate, sodium tetraborate, and potassium hydrogenphthalate, have been examined. Many primary standards absorb appreciable amounts of water when exposed to moist atmospheres. TG data can show the extent of this absorption and hence the most suitable drying temperature for a given reagent may be determined. 

The purity of 1 and 2 is assessed by analytical gas-liquid chromatography (GC) on a Hewlett-Packard 5890 gas chromatograph equipped with a flame-ionization detector and fitted with a 50 m x 0.2 mm HP-5 fused silica glass capillary column using linear temperature programming from an initial temperature of 150°C for 5 min to a final temperature of 200°C for 10 min at a rate of 5°C/min. 

---