Epoxidized oil

Typically, soHd stabilizers utilize natural saturated fatty acid ligands with chain lengths of Cg—C g. Ziac stearate [557-05-1/, ziac neodecanoate [27253-29-8] calcium stearate [1592-23-0] barium stearate [6865-35-6] and cadmium laurate [2605-44-9] are some examples. To complete the package, the soHd products also contain other soHd additives such as polyols, antioxidants, and lubricants. Liquid stabilizers can make use of metal soaps of oleic acid, tall oil acids, 2-ethyl-hexanoic acid, octylphenol, and nonylphenol. Barium bis(nonylphenate) [41157-58-8] ziac 2-ethyIhexanoate [136-53-8], cadmium 2-ethyIhexanoate [2420-98-6], and overbased barium tallate [68855-79-8] are normally used ia the Hquid formulations along with solubilizers such as plasticizers, phosphites, and/or epoxidized oils. The majority of the Hquid barium—cadmium formulations rely on barium nonylphenate as the source of that metal. There are even some mixed metal stabilizers suppHed as pastes. The U.S. FDA approved calcium—zinc stabilizers are good examples because they contain a mixture of calcium stearate and ziac stearate suspended ia epoxidized soya oil. Table 4 shows examples of typical mixed metal stabilizers. 

Polymerized oils Hydroxystearates Epoxidized oils Halogenated oils Polymerized oils Sulfonated oils... 

Epoxidized oils were also used to modify PLA Ali et ah (2009) reported that its use as a plasticizer to improve flexibility. Thermal and scanning electron microscope analysis revealed that epoxidized soybean oil is partially miscible with PLA. Rheological and mechanical properties of PLA/epoxidized soybean oil blends were studied by Xu and Qu (2009) Epoxidized soybean oil exhibited a positive effect on both the elongation at break and melt rheology. Al-Mulla et al. (2010b) also reported that plasticization of PLA (epoxidized palm oil) was carried out via solution casting process using chloroform as a solvent. The results indicated that improved flexibility could be achieved by incorporation of epoxidized palm oil. 

Table IV summarizes the glass transition temperature of a number of special functional oil-based homopolymers. Many of the polymers shown indeed have T s below the critical value. It is now believed that the synthetically epoxidized oils were fully epoxidized, producing materials with unusually high degrees of crosslinking, which tended to raise their T s beyond the desirable range.

OHM/TADS. 1985b. Heptachlor epoxide. Oil and Hazardous Materials/Technical Assistance Data System. Chemical Information Systems, Inc. December 1985. 

One species of Euphorbia in Brazil (Bernardia pulchelld) has been determined to contain more than 90% vemolic acid in the triglyceride [120]. This level of single-component purity is equivalent to the level of ricinoleic acid typically found in castor oil. These different varieties of epoxidized oil plants will probably continue to be the subject of agricultural development in the coming years. 

Epichlorohydrin Epoxidized Drying Oils Epoxidized Oils... 

Epoxy plasticizers are epoxidized oils and esters. These are generally classed with the polymeries. However, molecular weight is lower. Therefore, resistance to extraction and heat are slightly inferior, Low-temperature properties are better and epoxies are more easily incorporated. 

Another approach to the formation of the oxirane groups is the peroxidation of a carbon-carbon double bond. Various types of oligomers fall into this category epoxidized oils, epoxidized rubbers, and cycloaliphatic... 

Processing Additive Stabilizers Primary antioxidants (sterically hindered phenols, seoaryl amines) hydroperoxide decomposers (organophosphites, thioesters), acid absorbers (lead salts, Ca/Ba-Ba/Cd-Ba/Sn salts, organotins, epoxidized oils)... 

Epoxidized oils such as soybean oil or linseed oil, which are made by oxidizing the internal unsaturation in the fatty acid chain, find much use as plasticizers, particularly in vinyl resins. An internal epoxy ring is much less reactive than a terminal epoxy ring and usually does not take part in typical epoxy curing reactions under mild conditions. These materials can be used as plasticizers in epoxy adhesives but cannot really be considered reactive diluents. 

Epoxidized oils, especially epoxidized soybean oil (ESBO), are used extensively as plasticizers and stabilizers for plastics, particularly polyvinyl chloride (PVC). A plasticizer increases the workability of a plastic while a stabilizer reduces the rate... 

Epoxides have received increased attention in view of their interest both as end-products and as chemical intermediates. Epoxidized oils—mainly high-oleic sunflower oil—and their ester derivatives have found important applications as plasticizers and additives for polyvinyl chloride (PVC). Epoxidized esters produced from high-oleic sunflower methyl esters have hydroxyl values of 0, oxirane values of 5.2/ 4.5, and iodine values of 1.7/1.5 (127)... 

Epoxidized oils such as soybean, linseed and tall oil fatty acids are also used as plasticizers. While they don t pose the same health risks as the phthalates, they have limited compatibility with PVC and cannot be used at high temperatures. 

Paraplex [Hall]. TM for polymeric plasticizers for polymers and resinous coatings. Primarily polyesters, but some are epoxidized oils that impart heat and light stability as well as plasticization. Supplied as viscous liquids in a range of molecular weights all at 100% solids. Compatible with polyvinyl chloride, polyvinyl butyral, cellulosics, and other high polymers and elastomers. 

The polymerization is said to be fast with a low energy input, is not inhibited by air, uses no solvents, is nonpolluting, and uses inexpensive materials. The photopolymerization of various epoxidized oils and terpenes also does this. The propenyl ethers were made by isomerization of the corresponding allyl ethers with a ruthenium catalyst. The allyl ethers were made from the hydroxy compounds with allyl bromide and base, a process that produces waste salts. It is possible that the monomers could be made by reaction of the hydroxy compounds with propylene oxide followed by dehydration so that no waste salts would be formed. Isosorbide is made by the acid-catalyzed dehydration of sorbitol, in turn, obtained by the reduction of glucose. 

There are three major types of epoxy resins cycloaliphatic epoxy resins (R and R are part of a six-membered ring), epoxidized oils (R and R are fragments of an unsaturated fatty acid, such as oleic acid in soybean oil), and glycidated resins (R is hydrogen and R can be a polyhydroxyphenol or a polybasic acid). The first two types of epoxy resins are obtained by the direct oxidation of the corresponding olefin with a peracid as illustrated by the following ... 

Recycling Rate Consumption from Cl Ions % (our results) Liberated Epoxidized Oil Consumption (%)... 

Natural soybean oil is too viscous and reactive to atmospheric oxygen to be used in many biobased product applications. These limitations must be overcome for soybean oil to be used in fuels, cosmetics, and lubricants, but on the other hand, soybean oil is not sufficiently reactive to be used in most paints and coatings. Important end-use categories for which economic data exist include fatty acids, paints and varnishes, resins and plastics, drying-oil products, and other industrial products. Coating vehicles (paints and varnishes) and epoxidized oils (resins and plastics) comprise 50% of... 

---