Ammonium chloride hydroxide

Ammonia alum Ammonium chloride, hydroxide, and molybdate Ammonium compounds, except for fertilizer Ammonium perchlorate Ammonium thiosulfate Barium compounds Bauxite, refined Beryllium oxide Bleach (calcium hypochlorite), industrial... 

The calcium oxide so produced is slaked to give a suspension of calcium hydroxide and this is heated with the filtrate from the carbonator which contains ammonium chloride ... 

Aqueous ammonia can also behave as a weak base giving hydroxide ions in solution. However, addition of aqueous ammonia to a solution of a cation which normally forms an insoluble hydroxide may not always precipitate the latter, because (a) the ammonia may form a complex ammine with the cation and (b) because the concentration of hydroxide ions available in aqueous ammonia may be insufficient to exceed the solubility product of the cation hydroxide. Effects (a) and (b) may operate simultaneously. The hydroxyl ion concentration of aqueous ammonia can be further reduced by the addition of ammonium chloride hence this mixture can be used to precipitate the hydroxides of, for example, aluminium and chrom-ium(III) but not nickel(II) or cobalt(II). 

Direct Titrations. The most convenient and simplest manner is the measured addition of a standard chelon solution to the sample solution (brought to the proper conditions of pH, buffer, etc.) until the metal ion is stoichiometrically chelated. Auxiliary complexing agents such as citrate, tartrate, or triethanolamine are added, if necessary, to prevent the precipitation of metal hydroxides or basic salts at the optimum pH for titration. Eor example, tartrate is added in the direct titration of lead. If a pH range of 9 to 10 is suitable, a buffer of ammonia and ammonium chloride is often added in relatively concentrated form, both to adjust the pH and to supply ammonia as an auxiliary complexing agent for those metal ions which form ammine complexes. A few metals, notably iron(III), bismuth, and thorium, are titrated in acid solution. 

Recovery of Ammonia. The filter Hquor contains unreacted sodium chloride and substantially all the ammonia with which the brine was originally saturated. The ammonia may be fixed or free. Fixed ammonia (ammonium chloride [12125-02-97]) corresponds stoichiometrically to the precipitated sodium bicarbonate. Free ammonia includes salts such as ammonium hydroxide, bicarbonate, and carbonate, and the several possible carbon—ammonia compounds that decompose at moderate temperatures. A sulfide solution may be added to the filter Hquor for corrosion protection. The sulfide is distilled for eventual absorption by the brine in the absorber. As the filter Hquor enters the distiller, it is preheated by indirect contact with departing gases. The warmed Hquor enters the main coke, tile, or bubble cap-fiUed sections of the distiller where heat decomposes the free ammonium compounds and steam strips the ammonia and carbon dioxide from the solution. 

This carbon dioxide-free solution is usually treated in an external, weU-agitated liming tank called a "prelimer." Then the ammonium chloride reacts with milk of lime and the resultant ammonia gas is vented back to the distiller. Hot calcium chloride solution, containing residual ammonia in the form of ammonium hydroxide, flows back to a lower section of the distiller. Low pressure steam sweeps practically all of the ammonia out of the limed solution. The final solution, known as "distiller waste," contains calcium chloride, unreacted sodium chloride, and excess lime. It is diluted by the condensed steam and the water in which the lime was conveyed to the reaction. Distiller waste also contains inert soHds brought in with the lime. In some plants, calcium chloride [10045-52-4], CaCl, is recovered from part of this solution. Close control of the distillation process is requited in order to thoroughly strip carbon dioxide, avoid waste of lime, and achieve nearly complete ammonia recovery. The hot (56°C) mixture of wet ammonia and carbon dioxide leaving the top of the distiller is cooled to remove water vapor before being sent back to the ammonia absorber. 

The Hquor is then treated with calcium hydroxide (milk of lime) which reacts with the fixed salts, mosdy ammonium chloride, to Hberate ammonia. The Hquor is regenerated in a steam stripping operation. 

Reactions of the Side Chain. Benzyl chloride is hydrolyzed slowly by boiling water and more rapidly at elevated temperature and pressure in the presence of alkaHes (11). Reaction with aqueous sodium cyanide, preferably in the presence of a quaternary ammonium chloride, produces phenylacetonitrile [140-29-4] in high yield (12). The presence of a lower molecular-weight alcohol gives faster rates and higher yields. In the presence of suitable catalysts benzyl chloride reacts with carbon monoxide to produce phenylacetic acid [103-82-2] (13—15). With different catalyst systems in the presence of calcium hydroxide, double carbonylation to phenylpymvic acid [156-06-9] occurs (16). Benzyl esters are formed by heating benzyl chloride with the sodium salts of acids benzyl ethers by reaction with sodium alkoxides. The ease of ether formation is improved by the use of phase-transfer catalysts (17) (see Catalysis, phase-thansfer). 

Laudanine, C20H25O4N, was isolated by Hesse. The crude alkaloid is purified by recrj stallisation from dilute alcohol for the removal of small quantities of cryptopine, or it may be dissolved in acetic acid and the solution poured into dilute caustic soda, when this impurity is precipitated and laudanine may be recovered from the filtrate by addition of ammonium chloride. It still contains its isomeride laudanidine, which may be separated by repeated crystallisation of the hydrochlorides, laudanidine accumulating in the aqueous mother liquors. The base crystallises from dilute alcohol, or from a mixture of alcohol and chloroform in rhombic prisms, m.p. 166°, [a]o 0°. It dissolves in solutions of alkali hydroxides, fornung metallic derivatives, which are precipitated by excess of alkali, but is nearly insoluble in solution of ammonia. The salts crystallise well ... 

The unconjugated ketone can be isolated if the enolate salt (59) is quenched with ammonium chloride 6-dehydrotestosterone affords androst-5-en-I7-ol-3-one in 74% yield under such conditions. If the intermediate enolate salt is quenched with water, the hydroxide ion so formed may isomerize the 5-en-3-one to the corresponding 4-en-3-one before the product can be isolated. 

While keeping the collected deuterioammonia at dry ice-isopropyl alcohol temperature, lithium wire (10 mg) is added, followed by a solution of 3/3-hydroxy-5a-cholest-7-en-6-one (161 50 mg) in anhydrous tetrahydrofuran (4 ml). The reaction mixture is stirred for 20 min, the cooling bath is then removed and the ammonia is allowed to boil under reflux for 40 min. A saturated solution of ammonium chloride in tetrahydrofuran is added dropwise until the deep blue color disappears and then the ammonia is allowed to evaporate. The residue is extracted with ether and the organic layer washed with dilute hydrochloric acid and sodium bicarbonate solution and then with water. Drying and evaporation of the solvent gives a semicrystalline residue which is dissolved in acetone and oxidized with 8 N chromic acid solution. After the usual workup the residue is dissolved in methanol containing sodium hydroxide (0.2 g) and heated under reflux for 1 hr to remove any deuterium introduced at C-5 or C-7. (For workup, see section II-B). 

AMMO 2.5 EC , cypermetlu-in, 13 Ammonia, 13 Ammonium acetate, 13 Ammonium arsenate, 13 Ammonium benzoate, 13 Ammonium bicarbonate, 13 Ammonium bifluoride, 14 Ammonium bisulfite, 14 Ammonium carbamate, 14 Ammonium carbonate, 14 Ammonium chloride, 14 Ammonium chlorplatmate, 14 Ammonium clu omate, 14 Ammonium citrate, 14 Ammonium diclu omate, 14 Ammonium fluoride, 14 Ammonium fomiate, 15 Ammonium hexafluorosilicate, 15 Ammonium hydroxide, 15 Ammonium metavanadate, 15 Ammonium molybdate, 15 Ammonium nitrate, 15 Ammonium oxalate, 15 Ammonium perfluorooctanoate, 15 Ammonium persulfate, 15 Ammonium phosphate, 15 Ammonium picrate, 16 Ammonium salicylate, 16... 

The manufacture of the cyclohexyl analog is as follows. Phenyl magnesium bromide was prepared from 48.5 g (0.308 mol) of bromobenzene, 7 g (0,29 mol) of magnesium, and 125 ml of dry ether. To it was added at 5°C over a period of A hour 40 g (0.18 mol) of cyclohexyl (3-(N-piperidyl)-ethyl ketone (BP 115° to 117°C/1 mm) in 125 ml of dry ether. The mixture was allowed slowly to come to room temperature, refluxed for one hour, and then poured into ice containing 80 ml of concentrated hydrochloric acid. Ammonium chloride (100 g) and 200 ml of concentrated ammonium hydroxide were added and the organic layer was separated. After drying and removing the solvent, the residue was distilled under reduced pressure. The base distilled at 158° to 170°C (1 mm) and solidified. Upon recrystallization from methanol it melted at 112° to 113°C. 

A suspension of 40 g 3-acetylaminomethyl-5-amino-2,4,6-triodobenzoic acid in 180 ml acetic anhydride were mixed with 0.4 ml concentrated sulfuric acid. An exothermic reaction was thereby initiated. Acetylation was completed by heating to 80°C for three hours. The reaction mixture was then evaporated to dryness in a vacuum at a temperature not exceeding 50°C. The residue was treated with a mixture of 30 ml concentrated aqueous ammonium hydroxide and 40 ml water, whereby the solid material dissolved with spontaneous heating. Within a few minutes, the ammonium salt of the acetylated product started precipitating. The precipitate and residual liquid were cooled externally with ice after about 15 minutes. The salt was separated from the liquid by filtration with suction, and was washed with ice cold saturated ammonium chloride solution. 

To a solution of thienyl magnesium bromide prepared from 21.4 g of magnesium and 144 g of 2-bromothiophene are added 39.B g of ethyl 4-dimethylaminocyclohexylcarboxylate. The mixture is ailowed to warm to room temperature and stirred for an additional six hours. The reaction mixture is then decomposed with dilute ammonium chloride solution and extracted with ether. The combined ether extracts are extracted thoroughiy with 10% hydrochloric acid and the acid solution made alkaline with ammonium hydroxide. The aqueous solution is extracted with chloroform which is then washed with water, dried and evaporated to a residue in vacuo. Recrystallization of the residue from hexane yields Oi.O -dithienyl-4-dimethyl-aminocyclohexyl carbinol, melting point 156°C to 157°C after recrystallization from benzene. 

S< dium Aluminato. . Ammonium Alum. . rola.uium Alum. . . Ammonia. . Ammonium (Ion). . Ammonium Chloride Ammonium Hydroxide Ammonium Sulfale... 

Ammonium chloride solutions are slightly acidic, so they are better solvents than water for insoluble hydroxides such as Mg(OH)2. Find the solubility of Mg(OH)2 in moles per liter in 0.2 M NH4CI and compare with the solubility in water. Hint Find K for the reaction... 

The addition of half a mole of ammonium chloride to 1 litre of a 0.1M solution of aqueous ammonia has decreased the degree of ionisation from 1.35 to 0.0036 per cent, and the hydroxide ion concentration from 0.00135 to 0.000 0036 mol L-1. 

Procedure. Prepare an EGTA solution (0.05M) by dissolving 19.01 g in 100 mL sodium hydroxide solution (1M) and diluting to 1 L in a graduated flask with de-ionised water. Prepare the indicator by dissolving 0.065 g zincon in 2 mL sodium hydroxide solution (0.1M) and diluting to 100 mL with de-ionised water, and a buffer solution (pH 10) by dissolving 25 g sodium tetraborate, 3.5 g ammonium chloride, and 5.7 g sodium hydroxide in 1 L of de-ionised water. 

Procedure. To a 50 mL sample of the water to be tested add 1 mL buffer solution (ammonium hydroxide/ammonium chloride, pH 10, Section 10.54) and 30-40 mg solochrome black indicator mixture. Titrate with standard EDTA solution (0.01 M) until the colour changes from red to pure blue. Should there be no magnesium present in the sample of water it is necessary to add 0.1 mL magnesium-EDTA solution (0.1 M) before adding the indicator (see Section 10.54). The total hardness is expressed in parts of CaC03 per million of water. 

As shown above the sulphide ion concentration of a saturated aqueous solution of hydrogen sulphide may be controlled within wide limits by suitably changing the concentration of hydrogen ions—a common ion—of the solution. In a like manner the hydroxide ion concentration of a solution of a weak base, such as aqueous ammonia (Kb = 1.8 x 10-5), may be regulated by the addition of a common ion, e.g. ammonium ions in the form of the completely dissociated ammonium chloride. The magnitude of the effect is best illustrated by means of an example. In a 0.1M ammonia solution, the degree of dissociation is given (Section 2.13) approximately by. 

An immediate application of the use of the aqueous ammonia-ammonium chloride mixture may be made to the familiar example of the prevention of precipitation of magnesium hydroxide (S.P. 1.5 x 0-11). We can first calculate the minimum hydroxide ion concentration necessary to prevent precipitation in, say, 0.1M magnesium solution. 

If an aqueous ammonia solution which is 0.1M is employed, the concentration of NH4 ion as ammonium chloride or other ammonium salt necessary to prevent the precipitation of magnesium hydroxide can be readily calculated as follows. Substituting in the mass action equation ... 

In the presence of interfering elements, proceed as follows. Neutralise 80-120mL of the solution containing 15-25mg of beryllium with ammonia solution until the hydroxides commence to precipitate. Re-dissolve the precipitate by the addition of a few drops of dilute hydrochloric acid. Add 0.5 g of ammonium chloride and sufficient 0.5M EDTA solution to complex all the heavy elements present. Add a slight excess of dilute ammonia solution, with stirring, boil for 2-3 minutes, add a little ashless filter pulp, filter, and complete the determination as above. 

Penta-1,3-diyne (Methyldiacetylene). CH3.CiC.CiCH mw 65.10 OB to C02 —294.93% liq mp —4.5 to -38.5° bp 76-77° (explds at atm press), 45° at 140mm d 0.7909 g/cc at 20/4° RI 1.4762 (Ref 3) and 1.4817 (Ref 1). Sol in ethanol and petr with a bp > 180°. Prepn is by reacting monosodium-acetylenide with dichloromethane in liq ammonia at 20 to 40°, followed by treatment with ammonium chloride. The product is stable in the dark at -35° but polymerizes readily at above —20° in the light. Penta-1,3-diyne forms two expl salts Copper penta-1,3-diyne, CuCsH3, dark yel ndls/by reaction with CuCl, explds on shock or by rubbing and Silver penta-1,3-diyne, yel-brn ndls, by reaction with aq silver nitrate in ammonium hydroxide, a v expl compd Refs 1) Beil 1, [247], 1057 <1117)... 

To a solution of hexamethyldisilane (2.5 mmol) in HMPA (CAUTION— CANCER SUSPECT AGENT) (3 ml) at 0-5 °C was added methyl lithium (2.5 mmol, 1.5 m MeLi.LiBr complex in ether) dropwise. After being stirred for 3 min, the red solution was treated with Cul (2.5 mmol) in Me2S (1 ml), the resulting black reaction mixture was stirred for 3 min. and 2,3-dibromo-propene (1 mmol) was added rapidly via a syringe. The reaction mixture was allowed to warm to room temperature, and was stirred for 1.5 h. It was then poured into pentane (25 ml) and saturated ammonium chloride solution (25 ml, buffered to pH 8 by the addition of ammonium hydroxide), and the mixture was stirred vigorously for 1 h. The aqueous phase was re-extracted with pentane, and the combined organic extracts were dried. Removal of... 

To a stirred solution of the alkynylsilane (20 mmol) and triethylbenzyl-ammonium chloride (0.7 mmol) in MeCN (15 ml) cooled to 0°C was added aqueous sodium hydroxide (15 ml, 12m). After 5-10min, the mixture was diluted with ether and extracted with ether/dichloromethane. Drying, concentration and suitable purification gave the free alkyne (80-90%). 

B. 2-Bromoallylatnine. Crude 2-bromoallylhexaminium bromide (204 g., 0.60 mole) is dissolved in a warm solution prepared from 400 ml. of water, 2 1. of ethanol, and 480 ml. (S.8 moles) of 121V hydrochloric acid. A white precipitate of ammonium chloride forms within an hour. The reaction mixture is allowed to stand for 24 hours, and the precipitate is removed by suction filtration. The mother liquor is concentrated to a volume of 600 ml. (Note 3), and the precipitate (Note 4) is removed by suction filtration. The mother liquor is evaporated to dryness (Note 5), and the residue is dissolved in 300 ml. of water. The solution is cooled in an ice bath and made strongly alkaline (pH 13) with 6N sodium hydroxide solution. 

The three-necked flask is charged with 750 ml. of formamide, 25 ml. of water, and 50 g. of ammonium chloride (Note 2). The mixture is heated to 180-190° in an oil bath, and 400 g. (3.02 moles) of 4,4-dimethoxy-2-butanone (Note 3) is added dropwise with stirring over the course of 6 hours (Note 4). The flow of cooling water in the reflux condenser should be adjusted to a rate such that the methanol and methyl formate formed during the reaction distil out (Note 5). After all the acetal has been added, heating is continued for 1 hour (Note 6). The mixture is allowed to cool and is poured into 1 1. of IN sodium hydroxide. The resultant solution is extracted with chloroform in a liquid-liquid extractor for 24 hours. The chloroform is separated, dried over sodium sulfate, and removed by distillation through a short column on a steam bath. 

---