Ethyl ketone

The properties of the solids most commonly encountered are tabulated. An important problem arises for petroleum fractions because data for the freezing point and enthalpy of fusion are very scarce. The MEK (methyl ethyl ketone) process utilizes the solvent s property that increases the partial fugacity of the paraffins in the liquid phase and thus favors their crystallization. The calculations for crystallization are sensitive and it is usually necessary to revert to experimental measurement. 

Methyl ethyl ketone. Use the apparatus of Fig. Ill, 61, 1 but with a 500 ml. round-bottomed flask. Place 40 g. (50 ml.) of see. butyl alcohol, 100 ml. of water and a few fragments of porous porcelain in the flask. Dissolve 100 g. of sodium dichromate dihydrate in 125 ml. of water in a beaker and add very slowly and with constant sturing 80 ml. of concentrated sulphuric acid allow to cool, and transfer the resulting solution to the dropping funnel. Heat the flask on a wire gauze or in an air bath until the alcohol mixture commences to boil. Remove the flame and run in the dichromate solution slowly and at such a rate that the temperature... 

Ethyl p-phenylethyl ketone. Use 100 g. of pure hydrocinnamic acid and 200 g. (201 -5 ml.) of pure propionic acid. Fractionation of the distillate yields 70 g. of diethyl ketone (b.p. 100-102°), 72 g. of ethyl p-phenyl-ethyl ketone (b.p. 245-249° the pure ketone boils at 248°), and 18 g, of crude di-p-phenylethyl ketone (high b.p. residue). 

The p-substituted amino ketones can be reduced readily to the more stable P-dialkylamino alcohols, many of which are useful local anaesthetics. Thus the local anaesthetic Tutocaine is made from the Mannich base derived from formaldehyde, methyl ethyl ketone and dimethylamine, followed by reduction and conversion into the p-aminobenzoate ... 

Methyl ethyl ketone is allowed to react with n-butyl or iso-amyl nitrite in the presence of hydrochloric acid to yield diacetyl monoxime (nitrosomethyl ethyl ketone) ... 

Science dealerships aren t the only places to get the stuff one needs. At those mega hardware stores one can find pure acetone, methanol, ethanol, toluene, methyl ethyl ketone, DCM(as a constituent of some stripping agents), sodium hydroxide in the form of lye, and some acids such as sulfuric and hydrochloric. These precious tools can be bought there cheaply and in great quantity. 

METHOD 4 [115]-80% phenol in aqueous H2SO4 soiution of pH 3 is brought to 50 C. 30% H2O2 is then added causing an exothermic reaction and a temperature of 15 C over 3-4 minutes time. 6% aqueous H2SO3 is added after 4.5 minutes, the solution quickly cooled and extracted with isopropyl acetone (Strike would think that another solvent like methyl ethyl ketone could be used) to give 60% catechol. 

Intermediates benzene to ethyl phenyl ketone to ethyl m nitrophenyl ketone to m aminophenyl ethyl ketone to ethyl m fluorophenyl ketone Reagents propanoyl chloride AICI3 HNO3 H2SO4 Fe HCl then HO NaN02 H2O HCl then HBF4 then heat... 

The osmotic pressure of polystyrene fractions in toluene and methyl ethyl ketone was measuredt at 25°C and the following results were obtained ... 

Fraction number Toluene Methyl ethyl ketone ... 

Figure 10.8 shows two sets of data plotted according to these conventions, after correction for the effect of interference. In Fig. 10.8a, HC2/T is plotted against C2 for three different fractions of polystyrene in methyl ethyl ketone. Figure 10.8b shows Kc2/Rg versus C2 for solutions of polystyrene in cyclohexane at five different temperatures. These results are discussed further in the following example.

Figure 10.8 Light-scattering data plotted to give slope-intercept values which can be interpreted in terms of M and B. (a) Polystyrene in methyl ethyl ketone. [From B. A. Brice, M. Halwer, and R. Speiser,/. Opt. Soc. Am. 40 768 (1950), used with permission.] (b) Polystyrene in cyclohexane at temperatures indicated. Units of ordinates are given in Example 10.4. [Reprinted with permission from W. R. Krigbaum and D. K. Carpenter,7. Phys. Chem. 59 1166 (1955), copyright 1955 by the American Chemical Society.]...

Bhatnagar and Biswast measured the turbidity at 436 nm of 2l single sample of poly(methyl methacrylate) in several solvents, including acetone and methyl ethyl ketone (MEK) ... 

---