Polymerization in reactor

If the inhibitor concentration, [H], is larger than necessary to satisfy the equality of Equation 2 there will be no polymerization in Reactor 1 and the inhibitor concentration entering Reactor 2 will be ... 

A more recent application of ultrasonics has been the characterization of the extent of polymerization in a condensation or radical process. The first observations were made by Sokolov, and subsequent reports of measurements on polystyrene, poly(vinyl chloride) and poly(vinyl acetate) " have confirmed the utility of the method. It is clear that this type of study is still in its infancy however, certain facts emerge which demonstrate the importance of this method. The compressibility of a solution containing monomer and polymer is directly related to the proportion of each component present. It is therefore possible to quantitatively estimate the extent of conversion from the observed velocity of sound. In a suspension polymerization, the glass transition of the polymer forming the bead is itself a function of the extent to which unreacted monomer is retained in the system. In this case, observation of the attenuation can indicate the extent to which polymerization has occurred in the system. Unfortunately the data are not sufficiently extensive to estimate the general validity of the method for the monitoring of polymerization in reactors, although the potential has been clearly demonstrated. 

After the mbber latex is produced, it is subjected to further polymerization in the presence of styrene (CgHg) and acrylonitrile (C H N) monomers to produce the ABS latex. This can be done in batch, semibatch, or continuous reactors. The other ingredients required for this polymerization are similar to those required for the mbber latex reaction. 

Polymerization in the Gas Phase. Many polymerization catalysts can be adapted for use in the gas phase. A gas-phase reactor contains a bed of small PE particles that is agitated either by a mechanical stirrer or by employing the fluidized-bed technique. These processes are economical because they do not requite solvent tecitculation streams. 

Some slurry processes use continuous stirred tank reactors and relatively heavy solvents (57) these ate employed by such companies as Hoechst, Montedison, Mitsubishi, Dow, and Nissan. In the Hoechst process (Eig. 4), hexane is used as the diluent. Reactors usually operate at 80—90°C and a total pressure of 1—3 MPa (10—30 psi). The solvent, ethylene, catalyst components, and hydrogen are all continuously fed into the reactor. The residence time of catalyst particles in the reactor is two to three hours. The polymer slurry may be transferred into a smaller reactor for post-polymerization. In most cases, molecular weight of polymer is controlled by the addition of hydrogen to both reactors. After the slurry exits the second reactor, the total charge is separated by a centrifuge into a Hquid stream and soHd polymer. The solvent is then steam-stripped from wet polymer, purified, and returned to the main reactor the wet polymer is dried and pelletized. Variations of this process are widely used throughout the world. 

An independent development of a high pressure polymerization technology has led to the use of molten polymer as a medium for catalytic ethylene polymerization. Some reactors previously used for free-radical ethylene polymerization at a high pressure (see Olefin polymers, low density polyethylene) have been converted to accommodate catalytic polymerization, both stirred-tank and tubular autoclaves operating at 30—200 MPa (4,500—30,000 psig) and 170—350°C (57,83,84). CdF Chimie uses a three-zone high pressure autoclave at zone temperatures of 215, 250, and 260°C (85). Residence times in all these reactors are short, typically less than one minute. 

Polymerization in Hquid monomer was pioneered by RexaH Dmg and Chemical and Phillips Petroleum (United States). In the RexaH process, Hquid propylene is polymerized in a stirred reactor to form a polymer slurry. This suspension is transferred to a cyclone to separate the polymer from gaseous monomer under atmospheric pressure. The gaseous monomer is then compressed, condensed, and recycled to the polymerizer (123). In the Phillips process, polymerization occurs in loop reactors, increasing the ratio of available heat-transfer surface to reactor volume (124). In both of these processes, high catalyst residues necessitate post-reactor treatment of the polymer. 

Third-generation high yield supported catalysts are also used in processes in which Hquid monomer is polymerized in continuous stirred tank reactors. The Hypol process (Mitsui Petrochemical), utilizes the same supported catalyst technology as the Spheripol process (133). Rexene has converted the hquid monomer process to the newer high yield catalysts. Shell uses its high yield (SHAC) catalysts to produce homopolymers and random copolymers in the Lippshac process (130). 

Solution Polymerization. In this process an inert solvent is added to the reaction mass. The solvent adds its heat capacity and reduces the viscosity, faciUtating convective heat transfer. The solvent can also be refluxed to remove heat. On the other hand, the solvent wastes reactor space and reduces both rate and molecular weight as compared to bulk polymerisation. Additional technology is needed to separate the polymer product and to recover and store the solvent. Both batch and continuous processes are used. 

Suspension Polymerization. In this process the organic reaction mass is dispersed in the form of droplets 0.01—1 mm in diameter in a continuous aqueous phase. Each droplet is a tiny bulk reactor. Heat is readily transferred from the droplets to the water, which has a large heat capacity and a low viscosity, faciUtating heat removal through a cooling jacket. 

The original wartime process was mn batchwise in reactors similar to those used for suspension polymerization. Since then, in many plants, the reactors have been hooked together as a series of continuous stirred tanks. 

Chlorinated by-products of ethylene oxychlorination typically include 1,1,2-trichloroethane chloral [75-87-6] (trichloroacetaldehyde) trichloroethylene [7901-6]-, 1,1-dichloroethane cis- and /n j -l,2-dichloroethylenes [156-59-2 and 156-60-5]-, 1,1-dichloroethylene [75-35-4] (vinyhdene chloride) 2-chloroethanol [107-07-3]-, ethyl chloride vinyl chloride mono-, di-, tri-, and tetrachloromethanes (methyl chloride [74-87-3], methylene chloride [75-09-2], chloroform, and carbon tetrachloride [56-23-5])-, and higher boiling compounds. The production of these compounds should be minimized to lower raw material costs, lessen the task of EDC purification, prevent fouling in the pyrolysis reactor, and minimize by-product handling and disposal. Of particular concern is chloral, because it polymerizes in the presence of strong acids. Chloral must be removed to prevent the formation of soflds which can foul and clog operating lines and controls (78). 

Polymerization Kinetics of Mass and Suspension PVC. The polymerization kinetics of mass and suspension PVC are considered together because a droplet of monomer in suspension polymerization can be considered to be a mass polymerization in a very tiny reactor. During polymerization, the polymer precipitates from the monomer when the chain size reaches 10—20 monomer units. The precipitated polymer remains swollen with monomer, but has a reduced radical termination rate. This leads to a higher concentration of radicals in the polymer gel and an increased polymerization rate at higher polymerization conversion. 

Continuous polymerization in a staged series of reactors is a variation of this process (82). In one example, a mixture of chloroprene, 2,3-dichloro-l,3-butadiene, dodecyl mercaptan, and phenothiazine (15 ppm) is fed to the first of a cascade of 7 reactors together with a water solution containing disproportionated potassium abietate, potassium hydroxide, and formamidine sulfinic acid catalyst. Residence time in each reactor is 25 min at 45°C for a total conversion of 66%. Potassium ion is used in place of sodium to minimize coagulum formation. In other examples, it was judged best to feed catalyst to each reactor in the cascade (83). 

Polymerization of raw feedstock. Aliphatic hydrocarbon resins. Raw feedstock contains straight-chain and cyclic molecules and mono- and diolefins. The most common initiator in the polymerization reaction is AICI3/HCI in xylene. The resinification consists of a two-stage polymerization in a reactor at 45°C and high pressure (10 MPa) for several hours. The resulting solution is treated with water and passed to distillation to obtain the aliphatic hydrocarbon resins. Several aliphatic hydrocarbon resins with different softening points can be adjusted. 

The reaction section consists of the high pressure reactors filled with catalyst, and means to take away or dissipate the high heat of reaction (300-500 Btu/lb of olefin polymerized). In the tubular reactors, the catalyst is inside a multiplicity of tubes which are cooled by a steam-water condensate jacket. Thus, the heat of reaction is utilized to generate high pressure steam. In the chamber process, the catalyst is held in several beds in a drum-type reactor with feed or recycled product introduced as a quench between the individual beds. 

Tosun, G., 1992. A mathematical model of mixing and polymerization in a semibatch stirred tank reactor. American Institution of Chemical Engineers Journal, 38, 425 37. 

Beaded polymeric supports are produced by a two-phase suspension polymerization in which microdrops of a monomer solution are directly converted to the corresponding microbeads. The size of a microdroplet is usually determined by a number of interrelated manufacturing parameters, which include the reactor design, the rate of stirring, the ratio of the monomer phase to water, the viscosity of both phases, and the type and concentration of the droplet stabilizer. 

Fig. 1. Examples of the kinetic curves during ethylene polymerization by chromium oxide catalysts. Support—SiOs temperature—80°C polymerization at constant ethylene pressure in perfect mixing reactor. Curve 1—catalyst reduced by CO at 300°C. Curve 2— catalyst activated in vacuum (400°C) polymerization in the case of (1) and (2) in solvent (heptane) ethylene pressure 10 kg/cm2 02 content in ethylene 1 ppm, HsO 3 ppm. Curves 3, 4, 5, 6—catalyst activated in vacuum (400°C) polymerization without solvent ethylene pressure 19 (curve 3), 13 (curve 4), 4 (curve 5), and 2 (curve 6) kg/cm2 02 content in ethylene 1 ppm, HsO = 12 ppm.

At higher water concentrations (at higher pressure) (Fig. 3.24), the reaction is considerably more rapid. The prepolymer obtained is further polymerized in another reactor, which has a working pressure of 1 bar or less. The total reaction time of the prepolymerization can be considerably shortened by processing it in an autoclave.812 28 In a laboratory, PA-6 can be synthesized in several ways from m-aminocaprolic acid, from lactam and from lactam and water, and anionically. 

In the diacid mediod, die PA salt is made first. A solution of this PA salt in water can be used for the polymerization. In the temperature range where the reaction rates are high, the diamines are volatile, and thus, it is preferable to carry out the prepolymerization under pressure. The prepolymerization can be carried out either at 220-250°C for 1 h or at 280-320°C in a matter of seconds. In the latter case, die reaction is carried out in a small-diameter tubular reactor.64 Although a prepolymerization under pressure is preferred, Nielinger28 has described a polymerization at atmospheric pressure at 210°C, whereby the loss in diamine is compensated for. 

A well-known high conversion reactor is the so-called polymerization press, a modified plate-and-frame filter press where polystyrene is polymerized in frames alternating between cooling platens through which water (or steam) can be circulated. Other versions of the high conversion reactor have been utilized, e.g., the early "can process of Dow, where styrene monomer was placed in sealed cans in water baths and the metal stripped off at the end of the polymerization 2). 

Hamielec and coworkers (, 42, 43) have conducted extensive experimental and theoretical studies with styrene polymerization in CSTR s. Theirs represent probably the first published work in this area at commercially interesting temperatures and conversions relating theory to experiment, and determining the effects of reactor configuration and conditions on conversion, molecular weight and MWD. 

Continuous Polymerizations As previously mentioned, fifteen continuous polymerizations in the tubular reactor were performed at different flow rates (i.e. (Nj g) ) with twelve runs using identical formulations and three runs having different emulsifier and initiator concentrations. A summary of the experimental runs is presented in Table IV and the styrene conversion vs reaction time data are presented graphically in Figures 7 to 9. It is important to note that the measurements of pressure and temperature profiles, flow rate and the latex properties indicated that steady state operation was reached after a period corresponding to twice the residence time in the tubular reactor. This agrees with Ghosh s results ). 

Gas phase olefin polymerizations are becoming important as manufacturing processes for high density polyethylene (HOPE) and polypropylene (PP). An understanding of the kinetics of these gas-powder polymerization reactions using a highly active TiCi s catalyst is vital to the careful operation of these processes. Well-proven models for both the hexane slurry process and the bulk process have been published. This article describes an extension of these models to gas phase polymerization in semibatch and continuous backmix reactors. 

The yield that can be attained by a semibatch process is generally higher because the semibatch run starts from scratch, with maximum values of both variables Cg (o) = Cg and k] (o) = k . However, the yield from a continuous run in which t equals the batch time is governed by the product of Cg (t) and kj (t), so > and k (t) = k °. Because neither of these conditions is likely to be fulfilled completely, a continuous polymerization in a backmix reactor will probably always fail to attain the Y attainable by a semibatch reactor at the same t. However, several backmix reactors in series will approach the behavior of a plug flow continuous reactor, which is equivalent to a semibatch reactor. 

Model GASPP was also used to correlate the results for polymerization at 20 atm, a 33% reduction in reactor pressure. Using the parameters for the most active BASF TiCil3, the model yields were 13% and 40% higher than the experimental yields. The 13% is... 

The study of the peak temperature sensitivity to the reactor operating parameters and the construction of sensitivity boundary curves for stable reactor operation were previously reported ( l). This paper presents a computer study on conceptual relationships between the conversion-product properties and the reactor operating parameters in a plug flow tubular reactor of free radical polymerization. In particular, a contour map of conversion-molecular weight relationships in a reactor of fixed size is presented and the sensitivity of its relationship to the choice of initiator system, solvent system and heat transfer system are discussed. 

The ability to manipulate reactor temperature profile in the polymerization tubular reactor is very important since it directly relates to conversion and resin product properties. This is often done by using different initiators at various concentrations and at different reactor jacket temperature. The reactor temperature response in terms of the difference between the jacket temperature and the peak temperature (0=Tp-Tj) is plotted in Figure 2 as a function of the jacket temperature for various inlet initiator concentrations. The temperature response not only depends on the jacket temperature but also, for certain combinations of the variables, it is very sensitive to the jacket temperature. 

An Experimental Study Using Feed Perturbations for a Free-Radically Initiated Homogeneous Polymerization in a Continuous-Flow Stirred-Tank Reactor... 

The influence of changes in these other variables on MWD in a homopolymerization has not yet been tested, but whatever perturbations are introduced to the feed in a radical polymerization in a laboratory-scale CSTR, they are unlikely to introduce dramatic changes in the MWD of the product because of the extremely short life-time of the active propagating chains in relation to the hold-up time of the reactor. This small change in MWD could be advantageous in a radically initiated copolymerization where perturbations in monomer feeds could give control over polymer compositions independent of the MWD. This postulate is being explored currently. 

Anionic Styrene Polymerization in a Continuous Stirred-Tank Reactor... 

Example 13.9 Illustrate temperature and molecular weight changes in a tubular reactor by constructing a simple model of styrene polymerization in a tube. 

A water-soluble, free-radical initiator is charged to the reactor and initiates polymerization in the water phase. 

There are many variations on this theme. Fed-batch and continuous emulsion polymerizations are common. Continuous polymerization in a CSTR is dynamically unstable when free emulsifier is present. Oscillations with periods of several hours will result, but these can be avoided by feeding the CSTR with seed particles made in a batch or tubular reactor. 

---