Temperature reactors

The choice of reactor temperature depends on many factors. Generally, the higher the rate of reaction, the smaller the reactor volume. Practical upper limits are set by safety considerations, materials-of-construction limitations, or maximum operating temperature for the catalyst. Whether the reaction system involves single or multiple reactions, and whether the reactions are reversible, also affects the choice of reactor temperature, as we shall now discuss. 

Temperature control. Let us now consider temperature control of the reactor. In the first instance, adiabatic operation of the reactor should be considered, since this leads to the simplest and cheapest reactor design. If adiabatic operation produces an unacceptable rise in temperature for exothermic reactions or an unacceptable fall in temperature for endothermic reactions, this can be dealt with in a number of ways  

Even if the reactor temperature is controlled within acceptable limits, the reactor effluent may need to be cooled rapidly, or quenched, to stop the reaction quickly to prevent excessive byproduct formation. This quench can be accomplished by indirect heat transfer using conventional heat transfer equipment or by direct heat transfer by mixing with another fluid. A commonly encountered situation is 

In fact, cooling of the reactor effluent by direct heat transfer can be used for a variety of reasons  

The liquid used for the direct heat transfer should be chosen such that it can be separated easily from the reactor product and so recycled with the minimum expense. Use of extraneous materials, i.e., materials that do not already exist in the process, should be avoided because it is often difficult to separate and recycle them with high efficiency. Extraneous material not recycled becomes an effluent problem. As we shall discuss later, the best way to deal with effluent problems is not to create them in the first place. 

The choice of reactor temperature depends on many factors. Consider first the effect of temperature on equilibrium conversion. A quantitative relationship can be developed as follows. Start by writing Equation 6.6 at constant pressure  

Equation 6.19 can be interpreted qualitatively to give guidance on the equilibrium conversion. If AG° is negative, the position of the equilibrium will correspond to the presence of more products than reactants (In Ka 0). If AG° is positive (In Ka 0), the reaction will not proceed to such an extent and reactants will predominate in the equilibrium mixture. Table 6.3 presents some guidelines as 

Source Reproduced from Smith EB, 1982, Basic Chemical Thermodynamics, 3rd Edition, by permission of Oxford University Press. 

Substituting Equation 6.31 into Equation 6.3 gives, after rearranging  

At standard conditions G and H are not functions of pressure, by definition. Thus, Equation 6.33 can be written at standard conditions for finite changes in G° and H° as  

---

Having considered reactor temperature and pressure, we are now in a position to judge whether the reactor phase will be gas, liquid, or multiphase. Given a free choice between gas- and liquid-phase reactions, operation in the liquid phase is usually preferred. Consider the single reaction system from Eq. (2.19) ... 

Very often the choice is not available. For example, if reactor temperature is above the critical temperature of the chemical species, then the reactor must be gas phase. Even if the temperature can be lowered below critical, an extremely high pressure may be required to operate in the liquid phase. 

The choice of reactor temperature, pressure, arid hence phase must, in the first instance, take account of the desired equilibrium and selectivity effects. If there is still freedom to choose between gas and liquid phase, operation in the liquid phase is preferred. 

Reactor temperature and pressure. If there is a significant difierence between the effect of temperature or pressure on primary and byproduct reactions, then temperature and pressure should be manipulated to improve selectivity and minimize the waste generated by byproduct formation. d. Catalysts. Catalysts cam have a major influence on selectivity. Changing the catalyst can change the relative influence on the primary and byproduct reactions. 

The preceding appropriate placement arguments assume that the process has the capacity to accept or give up the reactor heat duties at the given reactor temperature. A quantitative tool is needed to assess the capacity of the background process. For this purpose, the grand composite curve can be used and the reactor profile treated as if it was a utility, as explained in Chap. 6. 

The reaction uses a fixed-bed vanadium pentoxide-titanium dioxide catalyst which gives good selectivity for phthalic anhydride, providing temperature is controlled within relatively narrow limits. The reaction is carried out in the vapor phase with reactor temperatures typically in the range 380 to 400°C. 

Conversion at Equilibrium. The maximum urea conversion at equilibrium attainable at 185°C is ca 53% at infinite heating time. The conversion at equiUbtium can be increased either by raising the reactor temperature or by dehydrating ammonium carbamate in the presence of excess ammonia. Excess ammonia shifts the reaction to the right side of the overall equation ... 

This was a Hquid-phase process which used what was described as siUceous zeoUtic catalysts. Hydrogen was not required in the process. Reactor pressure was 4.5 MPa and WHSV of 0.68 kg oil/h kg catalyst. The initial reactor temperature was 127°C and was raised as the catalyst deactivated to maintain toluene conversion. The catalyst was regenerated after the temperature reached about 315°C. Regeneration consisted of conventional controlled burning of the coke deposit. The catalyst life was reported to be at least 1.5 yr. 

A reactor system is shown in Figure 2 to which the HAZOP procedure can be appHed. This reaction is exothermic, and a cooling system is provided to remove the excess energy of reaction. If the cooling flow is intermpted, the reactor temperature increases, leading to an increase in the reaction rate and the heat generation rate. The result could be a mnaway reaction with a subsequent increase in the vessel pressure possibly leading to a mpture of the vessel. 

The polymerization of monomers to form hydrocarbon resins is typically carried out by either the direct addition of catalyst to a hydrocarbon fraction or by the addition of feed to a solvent—catalyst slurry or solution. Most commercial manufacturers use a continuous polymerization process as opposed to a batch process. Reactor temperatures are typically in the range of 0—120°C. 

The batch process is similar to the semibatch process except that most or all of the ingredients are added at the beginning of the reaction. Heat generation during a pure batch process makes reactor temperature control difficult, especially for high soHds latices. Seed, usually at 5—10% soHds, is routinely made via a batch process to produce a uniform particle-size distribution. Most kinetic studies and models are based on batch processes (69). 

The highly exothermic nature of the butane-to-maleic anhydride reaction and the principal by-product reactions require substantial heat removal from the reactor. Thus the reaction is carried out in what is effectively a large multitubular heat exchanger which circulates a mixture of 53% potassium nitrate [7757-79-1/, KNO 40% sodium nitrite [7632-00-0], NaN02 and 7% sodium nitrate [7631-99-4], NaNO. Reaction tube diameters are kept at a minimum 25—30 mm in outside diameter to faciUtate heat removal. Reactor tube lengths are between 3 and 6 meters. The exothermic heat of reaction is removed from the salt mixture by the production of steam in an external salt cooler. Reactor temperatures are in the range of 390 to 430°C. Despite the rapid circulation of salt on the shell side of the reactor, catalyst temperatures can be 40 to 60°C higher than the salt temperature. The butane to maleic anhydride reaction typically reaches its maximum efficiency (maximum yield) at about 85% butane conversion. Reported molar yields are typically 50 to 60%. 

The naphthalene is vaporized, mixed with air, and fed to the top of the reactor. This process also allows for mixtures of ortho- s.yXen.e [95-47-6] to be mixed with the naphthalene and air, which permits the use of dual feedstocks. Both feedstocks are oxidized to phthaUc anhydride. The typical range of reactor temperature is 340—380°C. The reactor temperatures are controlled by an external molten salt. 

When cyclohexane is nitrated to produce nitrocyclohexane [1122-60-7] the foUowiag techniques minimise undesired C—C breakage ia the ring low temperature nitrations with NO2 (31), carefiil control of the reactor temperatures, and use of halogen additives. Oxygen iacreases the level of C—C bond breakage. 

Solvent Process. In the solvent process, or solvent cook, water formed from the reaction is removed from the reactor as an a2eotropic mixture with an added solvent, typically xylene. Usually between 3 to 10 wt % of the solvent, based on the total charge, is added at the beginning of the esterification step. The mixed vapor passes through a condenser. The condensed water and solvent have low solubiUty in each other and phase separation is allowed to occur in an automatic decanter. The water is removed, usually to a measuring vessel. The amount of water collected can be monitored as one of the indicators of the extent of the reaction. The solvent is continuously returned to the reactor to be recycled. Typical equipment for this process is shown in Figure 2. The reactor temperature is modulated by the amount and type of refluxing solvent. Typical conditions are ... 

Ethylbenzene Hydroperoxide Process. Figure 4 shows the process flow sheet for production of propylene oxide and styrene via the use of ethylbenzene hydroperoxide (EBHP). Liquid-phase oxidation of ethylbenzene with air or oxygen occurs at 206—275 kPa (30—40 psia) and 140—150°C, and 2—2.5 h are required for a 10—15% conversion to the hydroperoxide. Recycle of an inert gas, such as nitrogen, is used to control reactor temperature. Impurities ia the ethylbenzene, such as water, are controlled to minimize decomposition of the hydroperoxide product and are sometimes added to enhance product formation. Selectivity to by-products include 8—10% acetophenone, 5—7% 1-phenylethanol, and <1% organic acids. EBHP is concentrated to 30—35% by distillation. The overhead ethylbenzene is recycled back to the oxidation reactor (170—172). 

Ethylene oxide is produced in large, multitubular reactors cooled by pressurized boiling Hquids, eg, kerosene and water. Up to 100 metric tons of catalyst may be used in a plant. Typical feed stream contains about 30% ethylene, 7—9% oxygen, 5—7% carbon dioxide the balance is diluent plus 2—5 ppmw of a halogenated moderator. Typical reactor temperatures are in the range 230—300°C. Most producers use newer versions of the Shell cesium-promoted silver on alumina catalyst developed in the mid-1970s. 

Thus the ECCU always operates in complete heat balance at any desired hydrocarbon feed rate and reactor temperature this heat balance is achieved in units such as the one shown in Eigure 1 by varying the catalyst circulation rate. Catalyst flow is controlled by a sHde valve located in the catalyst transfer line from the regenerator to the reactor and in the catalyst return line from the reactor to the regenerator. In some older style units of the Exxon Model IV-type, where catalyst flow is controlled by pressure balance between the reactor and regenerator, the heat-balance control is more often achieved by changing the temperature of the hydrocarbon feed entering the riser. 

Methane, chlorine, and recycled chloromethanes are fed to a tubular reactor at a reactor temperature of 490—530°C to yield all four chlorinated methane derivatives (14). Similarly, chlorination of ethane produces ethyl chloride and higher chlorinated ethanes. The process is employed commercially to produce l,l,l-trichloroethane. l,l,l-Trichloroethane is also produced via chlorination of 1,1-dichloroethane with l,l,2-trichloroethane as a coproduct (15). Hexachlorocyclopentadiene is formed by a complex series of chlorination, cyclization, and dechlorination reactions. First, substitutive chlorination of pentanes is carried out by either photochemical or thermal methods to give a product with 6—7 atoms of chlorine per mole of pentane. The polychloropentane product mixed with excess chlorine is then passed through a porous bed of Fuller s earth or silica at 350—500°C to give hexachlorocyclopentadiene. Cyclopentadiene is another possible feedstock for the production of hexachlorocyclopentadiene. 

Two variables of primary importance, which are interdependent, are reaction temperature and ch1orine propy1ene ratio. Propylene is typically used ia excess to act as a diluent and heat sink, thus minimising by-products (eqs.2 and 3). Since higher temperatures favor the desired reaction, standard practice generally involves preheat of the reactor feeds to at least 200°C prior to combination. The heat of reaction is then responsible for further increases in the reaction temperature toward 510°C. The chlorine propylene ratio is adjusted so that, for given preheat temperatures, the desired ultimate reaction temperature is maintained. For example, at a chlorine propylene molar ratio of 0.315, feed temperatures of 200°C (propylene) and 50°C (chlorine) produce an ultimate reaction temperature of approximately 500°C (10). Increases in preheat temperature toward the ultimate reactor temperature, eg, in attempts to decrease yield of equation 1, must be compensated for in reduced chlorine propylene ratio, which reduces the fraction of propylene converted and, thus aHyl chloride quantity produced. A suitable economic optimum combination of preheat temperature and chlorine propylene ratio can be readily deterrnined for individual cases. 

---