Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Frame filter press

Solution Filtration. The polymer solution, free of unacetylated ceUulose, rigid particle contaminants, and dirt, must pass through spinnerets with holes of 30—80 ]lni diameter. Multistage filtration, usuaUy through plate-and-frame filter presses with fabric and paper filter media, removes the extraneous matter before extmsion. Undesirable gelatinous particles, such as the hemiceUulose acetates from ceUulose impurities, tend to be sheared into smaller particles rather than removed. The solution is also aUowed to degas in hoi ding tanks after each state of filtration. [Pg.296]

The dark blue solution containing 5—10% of cellulose with a DP of 1000—2000 is filtered through a series of plate-and-frame filter presses using fine mesh metal screens to remove any particles that might block the spinneret holes. It is then deaerated under vacuum and stored ready for spinning. Unlike viscose dope, the cuprammonium cellulose [9050-09-3] solution is relatively stable. [Pg.351]

Plate-and-Frame Filter Presses. In the conventional plate-and-frame press (Fig. 14), a sequence of perforated square, or rectangular, plates alternating with hoUow frames is mounted on suitable supports and pressed together with hydrauHc or screw-driven rams. The plates are covered with a filter cloth which also forms the sealing gasket. The slurry is pumped iato the frames and the filtrate is drained from the plates. [Pg.398]

The earhest reverse osmosis and ultrafiltration units were based on flat membrane sheets ia arrangements similar to that of a plate and frame filter press. Siace then, mote efficient membrane configurations, ie, tubular, spiral wound, and hoUow fiber, have emerged (96—98). [Pg.382]

The filter press has the advantage of simplicity, low capital cost, flexibility, and ability to operate at high pressure in either a cake-filter or a clarifying-filter application. Floor-space and headroom needs per unit of filter area are small, and capacity can be adjusted by adding or removing plates and frames. Filter presses are cleaned easily, and the filter medium is easily replaced. With proper operation a denser, drier cake compared with that of most other filters is obtained. [Pg.1709]

Ergonomic issues in manual washing, unloading, setup, cleaning, shoveling of filter boxes, moving of portable units e.g. plate and frame filter press. [Pg.104]

Figure 8. Process flow scheme for plate-and-frame filter press. Figure 8. Process flow scheme for plate-and-frame filter press.
This device is similar to a plate-and-frame filter press but the whole plate assembly is also housed in a tank or pressure vessel. This design allows higher pressures to... [Pg.192]

A well-known high conversion reactor is the so-called polymerization press, a modified plate-and-frame filter press where polystyrene is polymerized in frames alternating between cooling platens through which water (or steam) can be circulated. Other versions of the high conversion reactor have been utilized, e.g., the early "can process of Dow, where styrene monomer was placed in sealed cans in water baths and the metal stripped off at the end of the polymerization 2). [Pg.73]

With many batch processes, the production rate will decrease during the production period for example, batch reactors and plate and frame filter presses, and there will be an optimum batch size, or optimum cycle time, that will give the minimum cost per unit of production. [Pg.30]

A plate-and-frame filter press consists of alternate solid plates and hollow frames in a sandwich arrangement. The open frames are covered by the filter medium (e.g., the filter cloth), and the slurry enters through the frames and deposits the cake on the filter medium. The operation is batch, in that the filter must be disassembled when the cake fills the frame space, then cleaned and reassembled, after which the entire process is repeated. A schematic of a plate-and-frame press is shown in Fig. 13-7. In the arrangement shown, all of the frames are in parallel and the total filter area (which appears in the equations) is... [Pg.407]

A plate-and-frame filter press contains 16 frames and operates at a constant flow rate of 30 gpm. Each frame has an active filtering area of 4 ft2, and it takes 15 min to disassemble, clean, and reassemble the press. The press must be shut down for disassembly when the pressure difference builds up to 10 psi. What is the total net filtration rate in gpm for a slurry having properties determined by the following lab test. A sample of the slurry is pumped at a constant pressure differential of 5 psi through 0.25 ft2 of the filter medium. After 3 min, 1 gal of filtrate has been collected. The resistance of the filter medium may be neglected. [Pg.412]

Filtration is carried out in a plate and frame filter press, with 20 frames 0.3 m square and 50 mm thick, and the rate of filtration is maintained constant for the first 300 s. During this period, the pressure is raised to 350 kN/m2, and one-quarter of the total filtrate per cycle is obtained. At the end of the constant rate period, filtration is continued at a constant pressure of 350 kN/m2 for a further 1800 s, after which the frames are full. The total volume of filtrate per cycle is 0.7 m3 and dismantling and refitting of the press takes 500 s. It is decided to use a rotary drum filter, 1.5 m long and 2.2 m in diameter, in place of the filter press. Assuming that the resistance of the cloth is the same in the two plants and that the filter cake is incompressible, calculate the speed of rotation of the drum which will result in the same overall rate of filtration as was obtained with the filter press. The filtration in the rotary filter is carried out at a constant pressure difference of 70 kN/m2, and the filter operates with 25 per cent of the drum submerged in the slurry at any instant. [Pg.75]

Data from the plate and frame filter press are used to evaluate the cake and cloth resistance for use with the rotary drum filter. [Pg.75]

It is required to filter a slurry to produce 2.25 m3 of filtrate per working day of 8 hours. The process is carried out in a plate and frame filter press with 0.45 m square frames and a working pressure difference of 348.7 kN/m2. The pressure is built up slowly over a period of 300 s and, during this period, the rate of filtration is maintained constant. [Pg.77]

Plate-and-frame filter presses are particularly suited to batch operations. Modern frames are made of polymers (mainly polypropylene), which have replaced wood as a building material. Large amounts of products, on the other hand, are filtered routinely via continuous-belt filters or rotary drum-type filters. Following the filtration step, inorganic salts are removed by washing with water. [Pg.203]

Only one basic design of electrodialysis equipment for demineralization appears to be in use. This is an assembly of alternate cation and anion ion exchange sheets separated by spacers in groups of several hundred clamped together between electrodes. The assembly physically resembles a plate-and-frame filter press. Figures 15.21(a) and (b) show such assemblies, and some dimensional data were stated in Section 15.5, Electrodialysis. [Pg.517]

A stainless steel, 11u x 11n x 2,f plate and frame filter press, closed delivery washing type... [Pg.529]

Product isolation involves cooling the reaction mixt to 100°, adding 40fi of w and vigorously stirring for 0.5 hours. The warm mixt is isolated in a plate and frame filter press, washed with 85° w for 1 hr and steamed for 1 hr. The product is then dried at 115° for a min of 16 hrs prior to sampling and packaging... [Pg.531]

Data taken from the plate and frame filter press located in the unit operations laboratory are used to determine a, the specific cake resistance, of a calcium carbonate slurry. Several values of a, expressed in ft/lb, have been calculated from data taken during the fall semester. [Pg.61]

Filtration. Filtration in Washington wineries is performed almost exclusively with plate-and-frame filter presses. In some cases, these filters have wide frames so that they are capable of performing diatomaceous earth filtrations. There is only one stainless steel, screened, diatomaceous earth, pressure-leaf filter in use in the Washington wine industry. Two major wineries have found they can utilize a paper septum over a medium pad in their plate-and-frame filters. This allows them to precoat and body feed with diatomaceous earth as the wine is filtered. This accomplishes both a coarse and medium filtration in one movement of the wine. [Pg.184]

Filter-pross electrolyzers, which are similar to a plate and frame filter press, are sucossfully used when gases are evolved in course of the electrolysis. Some designs of these types of electrolyzers will be described in detail in the chapter dealing with the electrolysis of water. The electrolyzer consists of number of frames with bipolar plate electrodes c which are separated by diaphragms d. Framos Fig. 18. Schematic diagram of a filter-press... [Pg.187]

Examples of pressure filters include the plate and frame filter press, which gives a variable filter area depending on the number of plates installed on the frame, improving flexibility. Cake washing is also possible with this type of filter. High-pressure contained-plate and frame filters are now available where separations are more difficult or where solvents are being handled. [Pg.641]

Vacuum filtration and screen-bowl centrifuges are the principal unit operations used for mechanical dewatering of fine coal. Pressure filtration (plate and frame filter presses and continuous belt filter presses) is used to a much lesser extent to dewater fine... [Pg.857]

Filtration. Filtration can include filter presses, rotary drum vacuum filters (RDVF), belt filters, and variations on synthetic membrane filtration equipment, such as filter cartridges, pancake filters, or plate and frame filter presses. These processes typically operate in a batch mode when the filter chamber is filled up or the vacuum drum cake is exhausted, a new batch must be started. This type of filtration is also called dead-end filtration because the only fluid flow is through the membrane itself. Due to the small size of cells and their compressible nature, typical cell cakes have low permeability and filter aids, such as diatomaceous earths, perlite, or other mined materials are added to overcome this limitation. Moreover, the presence of high solids and viscous polymeric fermentation byproducts can limit filtration fluxes without the use of filter aids. [Pg.1331]


See other pages where Frame filter press is mentioned: [Pg.398]    [Pg.469]    [Pg.389]    [Pg.81]    [Pg.1709]    [Pg.2238]    [Pg.185]    [Pg.186]    [Pg.412]    [Pg.376]    [Pg.376]    [Pg.1326]    [Pg.413]    [Pg.716]    [Pg.67]    [Pg.299]    [Pg.228]    [Pg.321]    [Pg.324]    [Pg.81]    [Pg.183]    [Pg.451]   
See also in sourсe #XX -- [ Pg.437 ]




SEARCH



Filter presses

Filters filter press

Plate and frame filter press

© 2024 chempedia.info