Immiscibility Immiscible

Immisc - immiscibility equilibria such as L1-L2 L1-L2-G L1-L2-S etc. Cr.ph-critical phenomena... 

The examples given above are, however, exceptions. In general, polymer blends are immiscible. Immiscible polymer blends usually exhibit ultimate mechanical properties such as elongation at break inferior to either of the pure components. This is notably the case in polyolefin-polystyrene blends. Another example of this inferiority of ultimate properties is found in studies of the tensile test energy to break in blends of polyethylene and polyamides [89]. 

Flotation. Flotation is a gravity separation process which exploits differences in the surface properties of particles. Gas bubbles are generated in a liquid and become attached to solid particles or immiscible liquid droplets, causing the particles or droplets to rise to the surface. This is used to separate mixtures of solid-solid particles and liquid-liquid mixtures of finely divided immiscible droplets. It is an important technique in mineral processing, where it is used to separate different types of ore. 

The principal point of interest to be discussed in this section is the manner in which the surface tension of a binary system varies with composition. The effects of other variables such as pressure and temperature are similar to those for pure substances, and the more elaborate treatment for two-component systems is not considered here. Also, the case of immiscible liquids is taken up in Section IV-2. 

Condensed phases of systems of category 1 may exhibit essentially ideal solution behavior, very nonideal behavior, or nearly complete immiscibility. An illustration of some of the complexities of behavior is given in Fig. IV-20, as described in the legend. 

If an ideal solution is formed, then the actual molecular A is just Aav (and Aex = 0). The same result obtains if the components are completely immiscible as illustrated in Fig. IV-21 for a mixture of arachidic acid and a merocyanine dye [116]. These systems are usually distinguished through the mosaic structure seen in microscopic evaluation. 

Fig. IV-21. Surface pressure versus area for monolayers of immiscible components a monolayer of pure cadmium arachidate (curve 1) and monolayers of mixed merocyanine dye, MC2, and cadmium arachidate of molar ratio r = 1 10 (curve 2) 1 5 (curve 3), 1 2 (curve 4), and pure MC2 (curve 5). The subphase is 2.5 x 0 M CdC, pH = 5.5 at 20°C. Curve 3a (O) was calculated from curves 1 and 5 using Eq. IV-44. (From Ref. [116].)...

The preceding definitions have been directed toward the treatment of the solid-liquid-gas contact angle. It is also quite possible to have a solid-liquid-liquid contact angle where two mutually immiscible liquids are involved. The same relationships apply, only now more care must be taken to specify the extent of mutual saturations. Thus for a solid and liquids A and B, Young s equation becomes... 

Koopal and co-workers [186] have extended this thermodynamic analysis to investigate the competitive wetting of a solid by two relatively immiscible liquids. They illustrate the tendency of silica to be preferentially wet by water over octane, a phenomenon of importance in oil reservoirs. 

If two pure, immiscible liquids, such as benzene and water, are vigorously shaken together, they will form a dispersion, but it is doubtful that one phase or the other will be uniquely continuous or dispersed. On stopping the agitation, phase separation occurs so quickly that it is questionable whether the term emulsion really should be applied to the system. A surfactant component is generally needed to obtain a stable or reasonably stable emulsion. Thus, if a little soap is added to the benzene-water system, the result on shaking is a true emulsion that separates out only very slowly. Theories of... 

Discuss briefly at least two reasons why two pure immiscible liquids do not form a stable emulsion. 

Crawford M J, Frey J G, VanderNoot T J and Zhao Y G 1996 Investigation of transport across an immiscible... 

The majority of practical micellar systems of Tionnal micelles use water as tire main solvent. Reverse micelles use water immiscible organic solvents, altlrough tire cores of reverse micelles are usually hydrated and may contain considerable quantities of water. Polar solvents such as glycerol, etlrylene glycol, fonnamide and hydrazine are now being used instead of water to support regular micelles [10]. Critical fluids such as critical carbon dioxide are... 

Micelles are mainly important because they solubilize immiscible solvents in their cores. Nonnal micelles solubilize relatively large quantities of oil or hydrocarbon and reverse micelles solubilize large quantities of water. This is because the headgroups are water loving and the tailgroups are oil loving. These simple solubilization trends produce microemulsions (see section C2.3.11). 

Other solubilization and partitioning phenomena are important, both within the context of microemulsions and in the absence of added immiscible solvent. In regular micellar solutions, micelles promote the solubility of many compounds otherwise insoluble in water. The amount of chemical component solubilized in a micellar solution will, typically, be much smaller than can be accommodated in microemulsion fonnation, such as when only a few molecules per micelle are solubilized. Such limited solubilization is nevertheless quite useful. The incoriDoration of minor quantities of pyrene and related optical probes into micelles are a key to the use of fluorescence depolarization in quantifying micellar aggregation numbers and micellar microviscosities [48]. Micellar solubilization makes it possible to measure acid-base or electrochemical properties of compounds otherwise insoluble in aqueous solution. Micellar solubilization facilitates micellar catalysis (see section C2.3.10) and emulsion polymerization (see section C2.3.12). On the other hand, there are untoward effects of micellar solubilization in practical applications of surfactants. Wlren one has a multiphase... 

For the separation of immiscible liquids a small separating funnel of the conventional type should be used whenever practicable, a pear-shaped funnel (Fig. 16, p. 35) of 5-10 ml. capacity being particularly... 

Steam Distillation. Distillation of a Pair of Immiscible Liquids. Steam distillation is a method for the isolation and purification of substances. It is applicable to liquids which are usually regarded as completely immiscible or to liquids which are miscible to only a very limited extent. In the following discussion it will be assumed that the liquids are completely immiscible. The saturated vapours of such completely immiscible liquids follow Dalton s law of partial pressures (1801), which may be stated when two or more gases or vapoms which do not react chemically with one another are mixed at constant temperature each gas exerts the same pressure as if it alone were present and that... 

Some liquids are practically immiscible e.g., water and mercury), whilst others e.g., water and ethyl alcohol or acetone) mix with one another in all proportions. Many examples are known, however, in which the liquids are partially miscible with one another. If, for example, water be added to ether or if ether be added to water and the mixture shaken, solution will take place up to a certain point beyond this point further addition of water on the one hand, or of ether on the other, will result in the formation of two liquid layers, one consisting of a saturated solution of water in ether and the other a saturated solution of ether in water. Two such mutually saturated solutions in equilibrium at a particular temperature are called conjugate solutions. It must be mentioned that there is no essential theoretical difference between liquids of partial and complete miscibility for, as wdll be shown below, the one may pass into the other with change of experimental conditions, such as temperature and, less frequently, of pressure. 

The theory of the process can best be illustrated by considering the operation, frequently carried out in the laboratory, of extracting an orgaiuc compound from its aqueous solution with an immiscible solvent. We are concerned here with the distribution law or partition law which, states that if to a system of two liquid layers, made up of two immiscible or slightly miscible components, is added a quantity of a third substance soluble in both layers, then the substance distributes itself between the two layers so that the ratio of the concentration in one solvent to the concentration in the second solvent remains constant at constant temperature. It is assumed that the molecular state of the substance is the same in both solvents. If and Cg are the concentrations in the layers A and B, then, at constant temperature ... 

---