Attenuated total reflection sampling technique

The attenuated total reflectance (ATR) technique is used commonly in the near-infrared for obtaining absorption spectra of thin Aims and opaque materials. The sample, of refractive index i, is placed in direct contact with a material which is transparent in the region of interest, such as thallium bromide/thallium iodide (known as KRS-5), silver chloride or germanium, of relatively high refractive index so that Then, as Figure 3.f8... 

X-ray photoelectron spectroscopy (XPS) was used for elemental analysis of plasma-deposited polymer films. The photoelectron spectrometer (Physical Electronics, Model 548) was used with an X-ray source of Mg Ka (1253.6 eV). Fourier transform infrared (FTIR) spectra of plasma polymers deposited on the steel substrate were recorded on a Perkin-Elmer Model 1750 spectrophotometer using the attenuated total reflection (ATR) technique. The silane plasma-deposited steel sample was cut to match precisely the surface of the reflection element, which was a high refractive index KRS-5 crystal. 

There is substantial history regarding the application of conventional vibrational spectroscopy methods to study the intact surface of skin, the extracted stratum corneum and the ceramide-cholesterol-fatty acid mixtures that constitute the primary lipid components of the barrier. The complexity of the barrier and the multiple phases formed by the interactions of the barrier components have begun to reveal the role of each of these substances in barrier structure and stability. The use of bulk phase IR to monitor lipid phase behavior and protein secondary structures in the epidermis, as well as in stratum corneum models, is also well established 24-28 In addition, in vivo and ex vivo attenuated total reflectance (ATR) techniques have examined the outer layers of skin to probe hydration levels, drug delivery and percutaneous absorption at a macroscopic level.29-32 Both mid-IR and near-IR spectroscopy have been used to differentiate pathological skin samples.33,34 The above studies, and many others too numerous to mention, lend confidence to the fact that the extension to IR imaging will produce useful results. 

The IR spectra of solid samples usually are recorded in transmission either by pressing samples into KBr pellets or grinding samples up as Nujol mulls. These two techniques are not considered suitable for surface analysis of paper documents. Fortunately, some information can be obtained by using internal and external reflectance techniques. Only the internal reflectance technique or the so-called attenuated total reflectance (ATR) technique will be discussed here. 

The use of infrared spectroscopy in the Earth and environmental sciences has been widespread for decades however, until development of the attenuated total reflectance (ATR) technique, the primary use was ex situ material characterization (Chen and Gardella, 1998 Tejedor-Tejedor et al., 1998 Degenhardt and McQuillan, 1999 Peak et al., 1999 Wijnja and Schulthess, 1999 Aral and Sparks, 2001 Kirwan et al., 2003). For the study of environmental systems, the strength of the ATR-Fourier transform infrared (FTIR) technique lies in its intrinsic surface sensitivity. Spectra are collected only from absorptions of an evanescent wave with a maximum penetration depth of several micrometers from the internal reflection element into the solution phase (Harrick, 1967). This short optical path length allows one to overcome any absorption due to an aqueous phase associated with the sample while maintaining a high sensitivity to species at the mineral-water interface (McQuillan, 2001). Therefore, ATR—FTIR represents a technique capable of performing in situ spectroscopic studies in real time. 

It should be mentioned that for most IR bands, absorption is sufficiently strong that samples must be thin. Alternatively, IR can be studied by reflectivity using attenuated total reflectance (ATM) techniques, but such measurements provide information about portions of the sample close to the surface which may not be the same as within bulk samples. 

Fig. 68. Direnzoite. Patterns collected from three different spots of the sample using the micro-lR attenuated total reflectance (ATR) technique in the range 4000... 1400 cm" [08G1].

For on-bead analysis vibrational spectroscopy (IR-spectroscopy) can be employed attenuated total reflection is a method allowing fast and nondestructive on-bead analysis of small samples (single bead analysis) without significant sample preparation. Solid phase NMR is the method of choice if complex structural analysis is intended on the support. Spatially resolved analysis on the resin is possible with microscopic techniques. 

While electron or ion beam techniques can only be applied under ultra-high vacuum, optical techniques have no specific requirements concerning sample environment and are generally easier to use. The surface information which can be obtained is, however, quite different and mostly does not contain direct chemical information. While with infra-red attenuated total reflection spectroscopy (IR-ATR) a deep surface area with a typical depth of some micrometers is investigated, other techniques like phase-measurement interference microscopy (PMIM) have, due to interference effects, a much better surface sensitivity. PMIM is a very quick technique for surface roughness and homogeneity inspection with subnanometer resolution. 

It is generally assumed the fluorescence and Fourier transform mid-infrared (FT-IR) spectroscopies do not suffer from the above-mentioned inconveniences and may be applied to turbid samples. Front-face (fluorescence) and attenuated total reflection (FT-IR) techniques may provide information on the structure of adsorbed proteins. 

FTIR instrumentation is mature. A typical routine mid-IR spectrometer has KBr optics, best resolution of around 1cm-1, and a room temperature DTGS detector. Noise levels below 0.1 % T peak-to-peak can be achieved in a few seconds. The sample compartment will accommodate a variety of sampling accessories such as those for ATR (attenuated total reflection) and diffuse reflection. At present, IR spectra can be obtained with fast and very fast FTIR interferometers with microscopes, in reflection and microreflection, in diffusion, at very low or very high temperatures, in dilute solutions, etc. Hyphenated IR techniques such as PyFTIR, TG-FTIR, GC-FTIR, HPLC-FTIR and SEC-FTIR (Chapter 7) can simplify many problems and streamline the selection process by doing multiple analyses with one sampling. Solvent absorbance limits flow-through IR spectroscopy cells so as to make them impractical for polymer analysis. Advanced FTIR... 

For solid-phase samples or for membrane interaction studies, it can be very useful to use the alternative sampling technique of attenuated total reflectance (ATR). Films or solutions can be placed on a specially... 

Recently, polyethylene and Teflon mesh sample holders have been used. A drop of sample is placed on the mesh and spread to a relatively uniform thickness for analysis. These holders can often be rinsed and reused. A very convenient alternative to liquid sample holders is the technique called attenuated total reflection or ATR. The ATR cell is a crystal of gallium arsenide, GaAs and the infrared radiation enters one end of the trapezoidal crystal. With the angles adjusted to obtain total internal reflection, all of the IR radiation passes through the crystal and exits the other end as shown in Fig. 5.14. 

An infrared spectrum is a plot of percent radiation absorbed versus the frequency of the incident radiation given in wavenumbers (cm ) or in wave length ( xm). A variation of this method, diffuse reflectance spectroscopy, is used for samples with poor transmittance, e.g. cubic hematite crystals. Increased resolution and sensitivity as well as more rapid collection of data is provided by Fourier-transform-IR (FTIR), which averages a large number of spectra. Another IR technique makes use of attenuated total reflectance FTIR (ATR-FTIR) often using a cylindrical internal reflectance cell (CIR) (e.g. Tejedor-Tejedor Anderson, 1986). ATR enables wet systems and adsorbing species to be studied in situ. 

Attenuated total reflectance (ATR) is another recent development in sample handling (Fig. 5.8). In this case the sample may be run in a gel or cream and this method may be used to characterise both formulation matrices and their interactions with the drugs present in them. If the active ingredient is relatively concentrated and if a blank of the matrix is run using the same technique it may be subtracted from the sample to yield a spectrum of the active ingredient. ATR also provides another technique which can be used for the characterisation of polymorphs. 

Many polymers are too tough to be ground even at liquid nitrogen temperatures. Consequently, surface techniques are often used. Internal reflectance or attenuated total reflectance (ATR) is the second most commonly used infrared technique [38-40]. For soft or pliable polymers or solutions, ATR is an extremely versatile technique and the spectrum is similar to a transmission spectrum. Unlike transmission, the spectrum obtained is independent of sample thickness. 

Many techniques are based on this principle and can be used for the analysis of all types of samples. The spectrum obtained from reflected light is not identical to that obtained by transmittance. The spectral composition of the reflected beam depends on the variation of the refractive index of the compound with wavelength. This can lead to specular reflection, diffuse reflection or attenuated total reflection. Each device is designed to favour only one of the above. The recorded spectrum must be corrected using computer software. 

One other in situ technique can be used to determine fractional acidity in atmospheric aerosols by means of Fourier transform infrared (FTIR) spectroscopy (46). Originally, impactor samples were collected and were pressed into a KBr matrix, and then the IR spectrum was taken by attenuated total reflectance (ATR) FTIR spectroscopy to determine relative acidity, based on differences in absorption bands for sulfate and bisulfate species. Aerosols with [H+]/[S042 ] ratios greater than 1 could also be qualitatively identified. More recent innovations in the FTIR technique (47, 48) have made possible... 

The primary techniques used in this study include X-ray photoelectron spectroscopy (XPS), reflection-absorption infrared spectroscopy (RAIR), and attenuated total reflectance infrared spectroscopy (ATR). XPS is the most surface-sensitive technique of the three. It provides quantitative information about the elemental composition of near-surface regions (< ca. 50 A sampling depth), but gives the least specific information about chemical structure. RAIR is restricted to the study of thin films on reflective substrates and is ideal for film thicknesses of the order of a few tens of angstroms. As a vibrational spectroscopy, it provides the type of structure-specific information that is difficult to obtain from XPS. The... 

---