Specificity, measurement

If the mean or median provides an estimate of a penny s true mass, then the spread of the individual measurements must provide an estimate of the variability in the masses of individual pennies. Although spread is often defined relative to a specific measure of central tendency, its magnitude is independent of the central value. Changing all... 

Enclosed agitated filters are useful when volatile solvents are in use or when the solvent gives off toxic vapor or fume. Another significant advantage is that their operation does not require any manual labor. Control can be manual or automatic, usually by timers or by specific measurements of the product. Most filters are made of mild steel, with the exposed surfaces protected by lead, tile, mbber lining, or by coating or spraying with other substances as necessary. Filtration areas up to 10 m are available and the maximum cake thickness is 1 m. Apphcations are mainly in the chemical industry for the recovery of solvents. 

The most commonly measured pigment properties ate elemental analysis, impurity content, crystal stmcture, particle size and shape, particle size distribution, density, and surface area. These parameters are measured so that pigments producers can better control production, and set up meaningful physical and chemical pigments specifications. Measurements of these properties ate not specific only to pigments. The techniques appHed are commonly used to characterize powders and soHd materials and the measutiag methods have been standardized ia various iadustries. 

The Co nucleus decays with a half-life of 5.27 years by /5 emission to the levels in Ni. These levels then deexcite to the ground state of Ni by the emission of one or more y-rays. The spins and parities of these levels are known from a variety of measurements and require that the two strong y-rays of 1173 and 1332 keV both have E2 character, although the 1173 y could contain some admixture of M3. However, from the theoretical lifetime shown ia Table 7, the E2 contribution is expected to have a much shorter half-life and therefore also to dominate ia this decay. Although the emission probabilities of the strong 1173- and 1332-keV y-rays are so nearly equal that the difference cannot be determined by a direct measurement, from measurements of other parameters of the decay it can be determined that the 1332 is the stronger. Specifically, measurements of the continuous electron spectmm from the j3 -decay have shown that there is a branch of 0.12% to the 1332-keV level. When this, the weak y-rays, the internal conversion, and the internal-pair formation are all taken iato account, the relative emission probabilities of the two strong y-rays can be determined very accurately, as shown ia Table 8. 

Not all elements of the industrial thermocouple need to be wine. For example, if a copper pipe contains a flowing fluid whose temperature is to be measured, a constantan wine attached to the pipe will form a T, or copper—constantan, thermocouple. Such arrangements ate difficult to caUbrate and requite full understanding of the possible inherent problems. For example, is the copper pipe fully annealed Homogeneous Pure, or an alloy Many ingenious solutions to specific measurement problems ate given in Reference 6. 

Prior use. For the first installation of a specific measurement device at a site, training of maintenance personnel and purchases of spare parts might be necessaiy. 

Identifying the minimum number of specific measurements containing the most information such that the model parameters are uniquely estimated requires that the model and parameter estimates be known in advance. Repeated unit tests and model building exercises will ultimately lead to the appropriate measurements. However, for the first unit test in absence of a model, the identification of the minimum number of measurements is not possible. 

However, other bias errors are so substantial that their presence will significantly distort any conclusions drawn from the adjusted measurements. Rectification is the detection of the presence of significant bias in a set of measurements, the isolation of the specific measurements containing bias, and the removal of those measurements from subsequent reconcihation and interpretation. Significant bias in measurements is defined as gross error in the literature. 

Unlike the other two tests, this is associated with each measurement. Reconcihation is required before this test is apphed, but no further isolation is required. However, due to the limitations in reconciliation methods, some measurements can be inordinately adjusted because of incorrectly specified random errors. Other adjustments that do contain gross errors may not be adjusted because the selected constraints are not sensitive to these measurements. Therefore, even though the adjustment in each measurement is tested for gross error, rejection of the mill hypothesis for a specific measurement does not necessarily indicate that that measurement contains gross error. 

The authors test two methods coupled with the measurement test. In one, they sequentially eliminate measurements and rearrange the constraints to isolate the specific measurements that contain gross errors. In the other, streams are added back as the search continues. 

Recommendation When all measurements were recorded by hand, operators and engineers could use their judgment concerning their validity. Now with most acqmred automatically in enormous numbers, the measurements need to be examined automatically. The goal continues to be to detect correctly the presence or absence of gross errors and isolate which measurements contain those errors. Each of the tests has limitations. The hterature indicates that the measurement test or a composite test where measurements are sequentially added to the measurement set are the most powerful, but their success is limited. If automatic analysis is required, the composite measurement test is the most direct to isolation-specific measurements with gross error. 

Conduct a lab test to measure the bulk densities of several filter aids. If you don t have the chemicals, then describe how you would do the tests and what specific measurements and calculations are needed. 

For supply inlets in rooms some performance measurements exist, such as air exchange and ventilation efficiencies (see Chapter 8). It is usually not possible to use these for local ventilation supply inlets, and for the moment there are no specific measurements to evaluate the influence of an inlet on contaminants. Some trials with comparison indices, which compare inhaled concentrations (or exposures) with and without a supply inlet, have been done. 

Specific measuring range The range of concentration values for w hich the overall uncertainty of a measurement procedure is intended to lie within specific limits. 

Optimum Mixture A specific mixture of fuel and oxidant that yields the most rapid comhustion at a specific measured quantity or that yields the lowest value of the minimum ignition energy or that produces the maximum deflagration pressure. The optimum mixture is not always the same for each comhustion property that is measured. 

Analysis of the results you gather should include two dimensions facility-specific and companywide. As you review each facility s data, you will be gauging its performance against specific measures such as schedule and resource requirements. Companywide, the team should be looking not only for these measurements against the overall plan, but also for trends and common findings that may indicate systemic problems. 

Process workers often complain that valves are inaccessible. Emergency valves should always be readily accessible but other valves, if they are operated, say, once a year or less often, can be out of reach. It is reasonable to expect workers to get a ladder or scramble into a pipe trench at this frequency. Designers should remember that if a valve is just within reach of an average person then half of the population cannot reach it. Equipment should be placed such that at least 95% of the population can reach it. Guidance on specific measurements to achieve this objective is available in a number of standard human factors textbooks (see Bibliography). 

A less time consuming alternative to the saponifica-tion/malate dehydrogenase assay is the albeit less specific measurement of the carboxylic ester groups according to Kak c and Vejdelek [10]. The sample (160 /xl) is... 

Broadband or overall RMS data is strictly a gross value or number that represents the total vibration of the machine at the specific measurement point where the data was acquired. It does not provide any information pertaining to the individual frequency components or machine dynamics that created the measured value. 

Except for occasional bursts of irregularity when specific measures are particularly sensitive to the topology and may show unexpectedly large absolute deviations, range independent class-2 rules generally possess regular, predictable profiles which are relatively insensitive to exact g topologies. 

A, basically the KB for an antagonist but specifically measured in a biochemical binding study (or enzyme assay). 

D. Specific measures concerning prevention of transmission of animal Spongiform Encephalopathies (TSEs) (if applicable)... 

By virtue of the broad diversity of products covered under the medical devices umbrella, GMP regulations and standards for devices tend to be less specific than their drug GMP counterparts. However, it is expected that the manufacturer will use risk analysis to identify specific measures that are appropriate to the manufacturing process under consideration. In effect, this means that many of the GM P measures applicable to drugs will also apply to devices. For example, if a manufacturer is... 

Overall, there is excellent agreement between the three different experiments, and between the enantiomer specific measurements made at the LURE and Elettra synchrotrons. The PECO reaches its maximum magnitude... 

Only two of the 10 countries have devised specific measures for the benefit of consumers. The Australian dmg regulatory system also provides for the inclusion of consumer group representatives on various drug regulatory committees. The appeals system in the Netherlands is not limited to industry, but is also open to consumers. 

The extent to which one individual analyte can be measured undisturbedly in a real sample by a specific reagent, a particular sensor or a comparable specific measuring system. 

Since ideally, a biosensor should be reagentless, that is, should be able to specifically measure the concentration of an analyte without a supply of reactants, attempts to develop such bioluminescence-based optical fibre biosensors were made for the measurements of NADH28 30. For this purpose, the coreactants, FMN and decanal, were entrapped either separately or together in a polymeric matrix placed between the optical fibre surface and the bacterial oxidoreductase-luciferase membrane. In the best configuration, the period of autonomy was 1.5 h during which about twenty reliable assays could be performed. 

With consideration to the quality of a bio or chemosensor it is therefore necessary to discuss the transduction principle, the quality of the sensitive layer and the data evaluation. These three issues will be discussed in this paper, with the focus on interferometric principles in the area of non-specific measurements using chemosensors and specific interaction processes in the case of biosensing. 

Measurement of relative humidity depends on the system used. Systems employing vacuum are usually evacuated prior to introduction of water vapor [29]. For cases in which there is not a gas-forming reaction occurring, measurement of total pressure in the system can be used as a measure of water vapor pressure. Systems in which air is not evacuated require specific measurement of water vapor pressure. (For the latter type of system, caution should be taken to assure that the relative humidity source is in close proximity to the solid, since the diffusion of water vapor through air to the solid is required to maintain a constant relative humidity in the immediate vicinity of the solid.) A wide variety of pressure measuring instrumentation is commercially available with varying accuracy, precision, and cost. 

---