Process equipment pumps

The data base contains failure rate data plus some failure mode information for process equipment - pumps, compressors, gas turbines, valves, vessels, heat exchangers etc. 

The main failure of equipment is a loss of process containment. The consequences depend on the properties and the amount of the leaking material and the conditions both inside and outside of process equipment. Pumps and compressors (Marshall, 1987) are perhaps the most vulnerable items of pressurised systems, because they contain moving parts and they are also subject to erosion and cavitation. Pumps and compressors produce also vibration, which may lead to fatigue failure. Both seals and bearings of pumps and compressors are liable to failure. In addition agitator systems present difficulties due to mechanical stresses, though they operate at much lower speeds than pumps. 

List of all process equipments, pumps, blowers, and machineries which need a drive. 

The conceptual design starts with balance calculations and preliminary studies. After that the block diagrams of the processes are created, which can be completed into preliminary flow sheets in the basic engineering phase. In this phase all necessary main equipment inquiry specifications, as well as other process equipment, pump, motor and tank lists are created. 

Figure 12 shows the plan and elevation views of a process unit piping (9). A dmm is supported off the piperack. Heat exchangers are located far enough back from the support columns so that they are accessible and their shell covers can be removed. Pumps are located underneath the piperack, but sufficient room is provided for maintenance equipment to access the motors and to remove the pump if necessary. The motor is always oriented away from the process equipment and located on that side of the piperack. Instmment valve drops are shown supported from the columns. The instmment trays themselves mn on the outside of the support columns. Flat turns are only made from the outside position of the piperack. Nozzle-to-nozzle pipe mns are made whenever possible. Larger lines are located on the outside of the piperack. Connections to nozzles above the rack are made from the top... 

Because carbon is difficult to machine, very tittle impervious carbon equipment is made. However, impervious graphite has been accepted as a standard material of constmction by the chemical process industry for the fabrication of process equipment, such as heat exchangers, pumps, valves, towers, pipe, and fittings (9,10). 

Distillation appHcations can be characterized by the type of materials separated, such as petroleum appHcations, gas separations, electrolyte separations, etc. These appHcations have specific characteristics in terms of the way or the correlations by which the physical properties are deterrnined or estimated the special configurations of the process equipment such as having side strippers, multiple product withdrawals, and internal pump arounds the presence of reactions or two Hquid phases etc. Various distillation programs can model these special characteristics of the appHcations to varying degrees and with more or less accuracy and efficiency. 

Overall Eactor Estimates. The next level of fixed capital estimate is based on a preliminary design that includes a flow sheet, material balances, energy balances, and enough equipment design to size all of the principal process equipment, including pumps and tanks. 

The thermal stabiUty of epoxy phenol—novolak resins is useful in adhesives, stmctural and electrical laminates, coatings, castings, and encapsulations for elevated temperature service (Table 3). Filament-wound pipe and storage tanks, liners for pumps and other chemical process equipment, and corrosion-resistant coatings are typical appHcations using the chemically resistant properties of epoxy novolak resins. 

Process Unit or Batch Unit A process unit is a collection of processing equipment that can, at least at certain times, be operated in a manner completely independent from the remainder of the plant. A process unit normally provides a specific function in the production of a batch of product . For example, a process unit might be a reactor complete with all associated equipment (jacket, recirculation pump, reflux condenser, and so on). However, each feed preparation tank is usually a separate process unit. With this separation, preparation of the feed for the next batch can be started as soon as the feed tank is emptied for the current batch. 

Equipment and Economics A veiy large electrodialysis plant would produce 500 /s of desalted water. A rather typical plant was built in 1993 to process 4700 mVday (54.4 /s). Capital costs for this plant, running on low-salinity brackish feed were 1,210,000 for all the process equipment, including pumps, membranes, instrumentation, and so on. Building and site preparation cost an additional 600,000. The building footprint is 300 itt. For plants above a threshold level of about 40 m Vday, process-equipment costs usually scale at around the 0.7 power, not too different from other process eqiiip-ment. On this basis, process equipment (excluding the ouilding) for a 2000 mVday plant would have a 1993 predicted cost of 665,000. 

Process equipment function changes with different steps in process sequence (e.g., same vessel used as feed tank, reactor, crystallizer pump... 

Process equipment function changes with different steps in process sequence (e.g., same vessel used as feed tank, reactor, crystallizer pump used to pump in/out). Instrumentation and controls not kept in phase with the current process step (e.g., control set points, interlocks etc.). 

The Guidelines for Process Equipment Reliability Data with Data Tables covers a variety of components used in the chemical process industry, including electrical equipment, analyzers, instrumentation and controls, detectors, heat exchangers, piping systems, rotating equipment (pump, compressor, and fan), valves, and fire protection systems. 

Closed drain headers are normally provided for safe drainage of equipment containing severely toxic, corrosive, pollutant or high cost chemicals (e.g., phenol, sulfuric acid, monoethanolamine, sulfur dioxide, catacarb) where there is an appreciable inventory in a number of processing vessels in a plant. The header should be at least 50 mm in diameter, and should be tied into the major vessels and equipment with 25 mm minimum size connections (20 mm is considered adequate for pumps). The header may be routed to a gravity drain drum (with recovery to the process by pump or gas pressurization), or to a pumpout pump returning to the process, or in the case of sulfuric acid, to an acid blowdown drum. 

Normally there is some connection between the airflow rate and noise and vibration generation. This could modify the building construction either to prevent spreading or to diminish the levels of noise and vibrations from the air-handling units. This naturally includes all parts of these units, i.e., fans, pumps, and valves (see Chapters 5 and 9). The demands on noise insulation also include the noise and vibrations from the process equipment, which often has a higher level of noise and vibration than the ventilation system. 

Ancillary equipment consists of the support equipment, other than process equipment, needed for a plant to function properly. Pipes, valves, and primary movers (e.g., pumps) are included in this categoiy. ... 

The suction pressure required ai the vacuum pump (in absolute pressure) is the actual process equipment operating pressure minus the pressure loss between the process equipment and the source of the vacuum. Note that absolute pressures must be used for these determinations and not gauge pressures. Also keep in mind that tlie absolute pressure at the vacuum pump must always be a lower absolute pressure than tlie absolute pressure at the process. 

Figure 2-47. Acceptable pressure losses between the vacuum vessel and the vacuum pump. Note reference sections on figure to system diagram to illustrate the sectional type hook-ups for connecting lines. Use 60% of the pressure loss read as acceptable loss for the system from process to vacuum pump, for initial estimate. P = pressure drop (torr) of line in question Po = operating pressure of vacuum process equipment, absolute, torr. By permission, Ryans, J. L. and Roper, D. L., Process Vacuum System Design Operation, McGraw-Hill Book Co., Inc., 1986 [18].

---