Ethers sulfonic acids

Reduce agitation and add the glycol ether, sulfonic acid, and alcohol ethoxylate. 

Excellent reviews on chemical structure, morphology and properties of acid-bearing polymers can be found in Mauritz and Moore (2004), Peckham and Holdcroft (2010) and Yang et al. (2008). The base polymer of the prototypical DuPont Nafion perfluorosulfonic acid (PFSA) ionomer, shown in Figure 1.13(left), consists of a tetrafluoroethylene (TFE) backbone with randomly attached pendant sidechains of perfluorinated vinyl ethers. Sulfonic acid groups are fixed at the sidechain heads (Kreuer et al., 2004 Tanimura and Matsuoka, 2004 Yang et al., 2008 Yoshitake and Watakabe, 2008). 

Using the optimal conditions for the radical terpolymerization of 4-[(a,/ ,/ -trifluorovinyl)oxy]bromobenzene with the fluoroalkenes, these authors reported the synthesis of new polymer electrolyte membranes based on fluoropolymers incorporating aromatic perfluorovinyl ether sulfonic acids [85,107]. In fact, a novel synthetic route for the preparation of perfluorovinyl ether monomer containing sulfonic functionalities, 4-[(a,, -trifluorovinyl)oxy]benzenesulfonic acid (TFVOBSA), was proposed. This monomer was synthesized in 72% overall yield. Further, the radical (co)- and terpolymerization of 4-[(a,, -trifluorovinyl)oxy] benzenesulfonyl chloride (TFVOBSC) with VDF, HFP, and PMVE (Fig. 2.25)... 

Souzy, R., Ameduri, B., Boutevin, B., Capron, P., Marsacq, D., Gebel, G. (2005) Protonconducting polymer electrolyte membranes based on fluoropolymers incorporating perfluorovinyl ether sulfonic acids and fluoroalkenes synthesis and characterization. Fuel Cells, 5, 383 397. 

Substitution Reactions on Side Chains. Because the benzyl carbon is the most reactive site on the propanoid side chain, many substitution reactions occur at this position. Typically, substitution reactions occur by attack of a nucleophilic reagent on a benzyl carbon present in the form of a carbonium ion or a methine group in a quinonemethide stmeture. In a reversal of the ether cleavage reactions described, benzyl alcohols and ethers may be transformed to alkyl or aryl ethers by acid-catalyzed etherifications or transetherifications with alcohol or phenol. The conversion of a benzyl alcohol or ether to a sulfonic acid group is among the most important side chain modification reactions because it is essential to the solubilization of lignin in the sulfite pulping process (17). 

The typical acid catalysts used for novolak resins are sulfuric acid, sulfonic acid, oxaUc acid, or occasionally phosphoric acid. Hydrochloric acid, although once widely used, has been abandoned because of the possible formation of toxic chloromethyl ether by-products. The type of acid catalyst used and reaction conditions affect resin stmcture and properties. For example, oxaUc acid, used for resins chosen for electrical appHcations, decomposes into volatile by-products at elevated processing temperatures. OxaUc acid-cataly2ed novolaks contain small amounts (1—2% of the original formaldehyde) of ben2odioxanes formed by the cycli2ation and dehydration of the ben2yl alcohol hemiformal intermediates. 

Phthalocyanine sulfonic acids, which can be used as direct cotton dyes (1), are obtained by heating the metal phthalocyanines in oleum. One to four sulfo groups can be introduced in the 4-position by varying concentration, temperature, and reaction time (103). Sulfonyl chlorides, which are important intermediates, can be prepared from chlorosulfonic acid and phthalocyanines (104). The positions of the sulfonyl chloride groups are the same as those of the sulfonic acids (103). Other derivatives, eg, chlormethylphthalocyanines (105—107), / /f-butyl (108—111), amino (112), ethers (109,110,113—116), thioethers (117,118), carboxyl acids (119—122), esters (123), cyanides (112,124—127), and nitrocompounds (126), can be synthesized. 

Anhydrous sulfonic acids, particularly linear alkylben2enesulfonic acids, are typically stored ia stainless steel containers, preferably type 304 or 316 stainless steel. Use of other metals, such as mild steel, contaminates the acid with iron (qv), causiag a darkening of the acid over time (27). The materials are usually viscous oils which may be stored and handled at 30—35°C for up to two months (27). AH other detergent-grade sulfonic acids, eg, alcohol sulfates, alcohol ether sulfates, alpha-olefin sulfonates, and alpha-sulfomethyl esters, are not stored owiag to iastabiUty. These are neutrali2ed to the desired salt. 

Specialty sulfonic acid-based surfactants make up a rather large portion of surfactant production in the United States. Approximately 136,000 metric tons of specialty sulfonic acid-based surfactants were produced in 1992, which included alpha-olefin sulfonates, sulfobetaines, sulfosuccinates, and alkyl diphenyl ether disulfonates (64). These materials found use in the areas of household cleaning products, cosmetics (qv), toiletries, emulsion polymerization, and agricultural chemical manufacture. 

SuIfona.tlon, Sulfonation is a common reaction with dialkyl sulfates, either by slow decomposition on heating with the release of SO or by attack at the sulfur end of the O—S bond (63). Reaction products are usually the dimethyl ether, methanol, sulfonic acid, and methyl sulfonates, corresponding to both routes. Reactive aromatics are commonly those with higher reactivity to electrophilic substitution at temperatures > 100° C. Tn phenylamine, diphenylmethylamine, anisole, and diphenyl ether exhibit ring sulfonation at 150—160°C, 140°C, 155—160°C, and 180—190°C, respectively, but diphenyl ketone and benzyl methyl ether do not react up to 190°C. Diphenyl amine methylates and then sulfonates. Catalysis of sulfonation of anthraquinone by dimethyl sulfate occurs with thaHium(III) oxide or mercury(II) oxide at 170°C. Alkyl interchange also gives sulfation. 

Methane sulfonic acid, trifluoroacetic acid, hydrogen iodide, and other Brmnsted acids can faciUtate 3 -acetoxy displacement (87,173). Displacement yields can also be enhanced by the addition of inorganic salts such as potassium thiocyanate and potassium iodide (174). Because initial displacement of the acetoxy by the added salt does not appear to occur, the role of these added salts is not clear. Under nonaqueous conditions, boron trifluoride complexes of ethers, alcohols, and acids also faciUtate displacement (87,175). 

Commercially, sulfonic acid ion-exchange resins are used in fixed-bed reactors to make these tertiary alkyl ethers (14). Since the reaction is very selective to tertiary olefins and also reversible, a two-step procedure is also used to recover commercially pure tertiary olefins from mixed olefin process streams. The corresponding tertiary alkyl ether is produced in the olefin mixture and then easily separated from the unreacted olefins by simple fractionation. The reaction is then reversed in a second step to make a commercially pure tertiary olefin, usually isobutylene or isoamylene. 

Rexyn 101 (polystyrene sulfonic acid), 80-91% yield.This method does not cleave the r-butyldimethylsilyl ether. 

D. ci - -Thiabicyclo[4 .. Q]nonan S,S-Dioxide [Benzo[c]thiophene 2,2-dioxide, cis-octahydro-]. A solution of the sulfide (43.0 g., 0.303 mole) in 11. of ether is cooled to 0° and treated dropwise while magnetically stirred with 1.01. of 0.65iV ethereal monoperphthalic acid (0.65 mole). The mixture is kept overnight at 0°, after which time the precipitated phthalic acid is separated by filtration and the filtrate concentrated with a rotary evaporator. Bulb-to-bulb distillation of the residual oil at 0.05-0.1 mm. affords the sulfone as a eolorless liquid (48.5-50 g., 92-95%) (Note 11). This product is crystallized from ether-hexane to give a colorless solid, m.p. 39-41° (Note 12). 

In a 250 ml Erlenmeyer flask covered with aluminum foil, 14.3 g (0.0381 mole) of 17a-acetoxy-3j5-hydroxypregn-5-en-20-one is mixed with 50 ml of tetra-hydrofuran, 7 ml ca. 0.076 mole) of dihydropyran, and 0.15 g of p-toluene-sulfonic acid monohydrate. The mixture is warmed to 40 + 5° where upon the steroid dissolves rapidly. The mixture is kept for 45 min and 1 ml of tetra-methylguanidine is added to neutralize the catalyst. Water (100 ml) is added and the organic solvent is removed using a rotary vacuum evaporator. The solid is taken up in ether, the solution is washed with water and saturated salt solution, dried over sodium sulfate, and then treated with Darco and filtered. Removal of the solvent followed by drying at 0.2 mm for 1 hr affords 18.4 g (theory is 17.5 g) of solid having an odor of dihydropyran. The infrared spectrum contains no hydroxyl bands and the crude material is not further purified. This compound has not been described in the literature. 

Ethylenedioxy-2l-acetoxypregn-4-en-3-one A solution containing 3,3 20,20-bisethylenedioxypregn-5-en-21-ol acetate (120 mg) and /7-toluene-sulfonic acid hydrate (12 mg) in dry acetone (3 ml) is allowed to stand at 22° for 14 hr. Sodium bicarbonate solution and ether are added and the organic layer is separated, washed with water, dried and evaporated. Crystallization of the residue from hexane yields 81 mg (75%) of 20-monoketal, mp 140-141°. 

Production and Uses of Aliphatic Compounds II Ether, Epoxide and Pnlyeiher, Carboxylic Acids and Their Denvatives, Sulfonic Acids, Toxicological Data of Aliphatic Fluorine Compounds (Ger) Liebig, H, Ulm, K Chem Ztg 100 3-14 270... 

In further modifications of these norprogestins, reaction of norethindrone with acetic anhydride in the presence of p-toluene-sulfonic acid, followed by hydrolysis of the first-formed enol acetate, affords norethindrone acetate (41). This in turn affords, on reaction with excess cyclopentanol in the presence of phosphorus pentoxide, the 3-cyclopentyl enol ether (42) the progestational component of Riglovic . Reduction of norethindrone affords the 3,17-diol. The 33-hydroxy compound is the desired product since reactions at 3 do not show nearly the stereoselectivity of those at 17 by virtue of the relative lack of stereo-directing proximate substituents, the formation of the desired isomer is engendered by use of a bulky reducing agent, lithium aluminum-tri-t-butoxide. Acetylation of the 33,173-diol iffords ethynodiol diacetate, one of the most potent oral proves tins (44). ... 

Amino-5-phenylthiomethoxyacetanilide in methanol solution is heated with N,N -bis-meth-oxycarbonyl-isothiourea-S-methyl ether with the addition of a catalytic amount of p-toluene-sulfonic acid for three hours with stirring under reflux. The mixture is then filtered hot and after cooling the febantel product crystallizes out. It is filtered off, rinsed with ether and dried under high vacuum to give the final product, melting at 129°C to 130°C. 

A Preparation of 11 -Methoxy-A -Estradiene-3,17-Dione 0.5 g of A -estradiene-11/3-ol-3,17-dione were dissolved at room temperature in 25 cc of methylene chloride containing 2% of methanol and after 5 mg of p-toluene-sulfonic acid were added, the reaction mixture was agitated for several minutes. Then the reaction mixture was poured into ice water, washed with water until the wash waters were neutral, and distilled to dryness under vacuum. The resulting residue was crystallized from ethyl ether to obtain 0.46 g of 11/3-methoxy-A -estradiene-3,17-dione having a MP of 140°C. 

The decanted aqueous phase was extracted three times with a total of 150 ml of ethyl acetate. The combined organic solutions were filtered over Clarcel and extracted three times with a total of 150 ml of an Iced normal aqueous methane-sulfonic acid solution. The combined acid extracts were rendered alkaline on an ice bath with 30 ml of ION caustic soda solution. The separated oil was extracted four times with a total of 200 ml of ether. The combined ethereal extracts were washed twelve times with a totai of 360 ml of distilled water, dried over anhydrous magnesium sulfate in the presence of 0.3 g of animal charcoal and evaporated under reduced pressure on a water bath at 40°C. The oily residue obtained (3.8 g) was dissolved in 30 ml of boiling acetonitrile. After cooling for 2 hours at 3°C, the crystals formed were separated, washed with 5 ml of acetonitrile and dried at ambient temperature at low pressure. 

The C2-symmetric epoxide 23 (Scheme 7) reacts smoothly with carbon nucleophiles. For example, treatment of 23 with lithium dimethylcuprate proceeds with inversion of configuration, resulting in the formation of alcohol 28. An important consequence of the C2 symmetry of 23 is that the attack of the organometallic reagent upon either one of the two epoxide carbons produces the same product. After simultaneous hydrogenolysis of the two benzyl ethers in 28, protection of the 1,2-diol as an acetonide ring can be easily achieved by the use of 2,2-dimethoxypropane and camphor-sulfonic acid (CSA). It is necessary to briefly expose the crude product from the latter reaction to methanol and CSA so that the mixed acyclic ketal can be cleaved (see 29—>30). Oxidation of alcohol 30 with pyridinium chlorochromate (PCC) provides alde-... 

Salts of diazonium ions with certain arenesulfonate ions also have a relatively high stability in the solid state. They are also used for inhibiting the decomposition of diazonium ions in solution. The most recent experimental data (Roller and Zollinger, 1970 Kampar et al., 1977) point to the formation of molecular complexes of the diazonium ions with the arenesulfonates rather than to diazosulfonates (ArN2 —0S02Ar ) as previously thought. For a diazonium ion in acetic acid/water (4 1) solutions of naphthalene derivatives, the complex equilibrium constants are found to increase in the order naphthalene < 1-methylnaphthalene < naphthalene-1-sulfonic acid < 1-naphthylmethanesulfonic acid. The sequence reflects the combined effects of the electron donor properties of these compounds and the Coulomb attraction between the diazonium cation and the sulfonate anions (where present). Arenediazonium salt solutions are also stabilized by crown ethers (see Sec. 11.2). 

Sulfonic acid catalysts can also be used to prepare poly(arylene ether sulfone)s, such as (CF3C0)20, polyphosphoric acid (PPA),26 MeS03H-P205 mixture,33 and CF3SO3H.34... 

Quentin may have been the first to sulfonate (arylene ether sulfone).168 In this patent, it was demonstrated that the bisphenol A polysulfone could be sulfonated by chlorosulfonic acid to produce a sulfonated polyfarylene ether sulfone), which was used for desalination via reverse osmosis. However, the chlorosulfonic acid may be capable of cleaving the bisphenol A polysulfone partially at the iso-propylidene link or it might induce branching and crosslinking reactions by... 

Herbert and Hay reported a bisphenolic monomer, 3,8-bis(4-hydroxyphenyl)-A-phenyl-1,2-naphthalimide (Table 6.1), as well as its corresponding polyf V-phenyl imido aryl ether sulfone) via transimidization reactions with hydrazine monohydrate, aliphatic amines, and an amino acid.193 These polysulfones with... 

---