Saturated salt solution, 4.32

In a 1500 ml. round-bottomed flask, carrying a reflux condenser, place 100 g. of pure cydohexanol, 250 ml. of concentrated hydrochloric acid and 80 g. of anhydrous calcium chloride heat the mixture on a boiling water bath for 10 hours with occasional shaking (1). Some hydrogen chloride is evolved, consequently the preparation should be conducted in the fume cupboard. Separate the upper layer from the cold reaction product, wash it successively with saturated salt solution, saturated sodium bicarbonate solution, saturated salt solution, and dry the crude cycZohexyl chloride with excess of anhydrous calcium chloride for at least 24 hours. Distil from a 150 ml. Claisen flask with fractionating side arm, and collect the pure product at 141-5-142-5°. The yield is 90 g. 

Ethyl S-n-butyl xanthate. Use 32 g. of potassium ethyl xanthate, 37 g. (23 ml.) of n-butyl iodide (Section 111,40) and 50 ml. of absolute ethyl alcohol. Reflux on a water bath for 3 hours. Pour into 150 ml. of water, saturate with salt (in order to facilitate the separation of the upper layer), remove the upper xanthate layer, wash it once with 25 ml. of saturated salt solution, and dry with anhydrous calcium chloride or anhydrous calcium sulphate. Distil from a 50 ml. Claisen flask under reduced pressure. Collect the pale yellow ethyl S-n-butyl xanthate at 90-91°/4 mm. The yield is 34 g. 

W. C. Blasedale, Equilibria in Saturated Salt Solutions, (ACS Monogr. Ser.) Reinhold PubHshing Corp., New York, 1927. 

Several aqueous systems should be considered in a similar manner. For example, in the selective removal of divalent cations from a saturated salt solution, the hydrated resin gives up a portion of its normal water content as it contacts the salt stream. In so doing, the particles shrink, and the inner pathways for ion migration become smaller. 

Slurry contains 35 g of API Standard Evaluation Base Clay per 350 cm saturated salt solution. 

Water Transport. Two methods of measuring water-vapor transmission rates (WVTR) ate commonly used. The newer method uses a Permatran-W (Modem Controls, Inc.). In this method a film sample is clamped over a saturated salt solution, which generates the desired humidity. Dry air sweeps past the other side of the film and past an infrared detector, which measures the water concentration in the gas. For a caUbrated flow rate of air, the rate of water addition can be calculated from the observed concentration in the sweep gas. From the steady-state rate, the WVTR can be calculated. In principle, the diffusion coefficient could be deterrnined by the method outlined in the previous section. However, only the steady-state region of the response is serviceable. Many different salt solutions can be used to make measurements at selected humidity differences however, in practice,... 

Commercially, HEC is available in a wide range of viscosity grades, ranging from greater than 500 mPa-s(=cP) at 1% soHds to less than 100 mPa-s(=cP) at 5% total soHds. Because HEC is nonionic, it can be dissolved in many salt solutions that do not dissolve other water-soluble polymers. It is soluble in most 10% salt solutions and in many 50% (or saturated) salt solutions such as sodium chloride and aluminum nitrate. As a rule, the lower substitution grades are more salt-tolerant. 

Reference electrodes are used in the measurement of potential [see the explanation to Eq. (2-1)]. A reference electrode is usually a metal/metal ion electrode. The electrolyte surrounding it is in electrolytically conducting contact via a diaphragm with the medium in which the object to be measured is situated. In most cases concentrated or saturated salt solutions are present in reference electrodes so that ions diffuse through the diaphragm into the medium. As a consequence, a diffusion potential arises at the diaphragm that is not taken into account in Eq. (2-1) and represents an error in the potential measurement. It is important that diffusion potentials be as small as possible or the same in the comparison of potential values. Table 3-1 provides information on reference electrodes. 

If the one-point calibration in ambient air is not sufficient, the next best approach is to use the calibration box method.- The air state is created in a closed box made of nonhygroscopic material, like metal or plastic. A controlled state of humidity is maintained by exposing the air in the box to a liquid surface of a saturated salt solution. In practice, a dish containing the saturated water solution of a salt is placed on supports at the bottom of the box. The air in the box is circulated by means of a small fan. The box should be airtight and positioned in a constant temperature environment. The calibrated instruments are placed in the box. A dewpoint hygrometer can be used as a reference. A wide range of humidity can be created by using solutions of different salts. Table 12.5 shows a few examples of equilibrium humidities achieved with different salt solutions. 

It is possible to control the relative humidity with sulfuric acid solutions of particular concentrations (Tab. 26) or with saturated salt solutions in contact with excess salt (Tab. 27). These liquids are placed in a conditioning chamber... 

To a solution of 1.38 g of estradiol 3-methyl ether (mp 118-119°) in 110 ml of anhydrous ether is added 140 ml of liquid ammonia followed by 1.4 g (42 eq per mole) of lithium wire in small pieces, and 10 min later 16 ml of absolute alcohol is added dropwise over a 10- to 20-min period. Occasionally frothing occurs during the last part of this addition but is easily controlled by stopping the stirrer temporarily. After removing most of the ammonia and carefully adding cold water, the product is extracted with ether, washed with Claisen alkali, water and saturated salt solution, and dried over sodium... 

In a 250 ml Erlenmeyer flask covered with aluminum foil, 14.3 g (0.0381 mole) of 17a-acetoxy-3j5-hydroxypregn-5-en-20-one is mixed with 50 ml of tetra-hydrofuran, 7 ml ca. 0.076 mole) of dihydropyran, and 0.15 g of p-toluene-sulfonic acid monohydrate. The mixture is warmed to 40 + 5° where upon the steroid dissolves rapidly. The mixture is kept for 45 min and 1 ml of tetra-methylguanidine is added to neutralize the catalyst. Water (100 ml) is added and the organic solvent is removed using a rotary vacuum evaporator. The solid is taken up in ether, the solution is washed with water and saturated salt solution, dried over sodium sulfate, and then treated with Darco and filtered. Removal of the solvent followed by drying at 0.2 mm for 1 hr affords 18.4 g (theory is 17.5 g) of solid having an odor of dihydropyran. The infrared spectrum contains no hydroxyl bands and the crude material is not further purified. This compound has not been described in the literature. 

The reduction is effected exactly as in Procedure 8a but using 0.61 g (0.088 g-atom) of lithium. After the crude reaction product has been washed well on the filter with cold water, it is dissolved in ethyl acetate, the solution is filtered through the sintered glass funnel to remove iron compounds from the ammonia, and the filtrate is extracted with saturated salt solution. The organic layer is dried over sodium sulfate and the solvent is removed. The solid residue is crystallized from methanol (120 ml) using Darco. The mixture is cooled in an ice-bath, the solid is collected, rinsed with cold methanol, and then air-dried to give 12.9 g (85%), mp 129-132° reported for the tetrahydropyranyi ether of 3j5-hydroxypregn-5-en-20-one, mp 129-131°. 

A total of 50 ml (0.15 moles) of a 3 ethereal solution of methylmagnesium bromide is added slowly to a vigorously stirred solution of 5.8 g (12.5 mmoles) or 3,3 20,20-bisethylenedioxy-5a,6a-epoxy-5a-pregnane-ll/l,17a,21-triol in 400 ml of tetrahydrofuran. The solution is heated under reflux for 24 hr, cooled and treated with 32 ml of saturated ammonium chloride solution. The supernatant is decanted and the residue is washed with several portions of tetrahydrofuran. The combined supernatants are evaporated and extracted with ethyl acetate, washed with saturated salt solution, dried and concentrated to give 4,55 g (75%) of 3,3 20,20-bisethylenedioxy-6 -methyl-5a-pregnane-5a,ll, 17a,21-tetrol mp 170-172° after crystallisation from acetone-petroleum ether. The analytical sample is crystallized from acetone-petroleum ether mp 175-177° [aJo —11° (CHCI3). 

A-Homo-estra- Q>),2,Aa-triene-4, l-dione (45) from the l-ketal mono-dibromocarbene adduct (43b). A solution of monoadduct 17-ketal (43b 0.46 g) and dry pyridine (20 ml) is heated at reflux for 2 hr. After cooling the reaction mixture, the pyridine hydrobromide (0.1 g) is removed by filtration and the filtrate is concentrated under reduced pressure. The resultant gum is dissolved in ether and washed successively with water, ice-cold 4 N hydrochloric acid, water, 5% aqueous sodium bicarbonate solution, water, saturated salt solution and dried over anhydrous magnesium sulfate. Evaporation of the solvent at reduced pressure gives 3-bromo-4-methoxy-A-homo-estra-2,4,5(10)-trien-17-one (44 0.22 g) mp 158-162° after crystallization from ether. 

Bromo-4-methoxy-A-homo-estra-2,4,5(10)-trien-17-one (44 0. 2g), is dissolved in formic acid, 2 ml of boron trifluoride etherate is added and the mixture is stirred vigorously at 0° for 2 hr. A brown mass ca. 0.12 g) is obtained after evaporation of the solvents at reduced pressure. This material is diluted with water and extracted with chloroform. The chloroform extracts are washed successively with water and saturated salt solution, dried over anhydrous magnesium sulfate and evaporated at reduced pressure to give 95 mg of a product which is purified by filtration through a column of neutral alumina and crystallization of the residue after evaporation of the solvent from ethyl acetate-petroleum ether. The resulting A-homo-estra-l(10),2,4a-triene-4,17-dione (45), mp 143-146°, is identical to the tropone (45) prepared from monoadduct 17-ketone (43a). 

Bromo-A-homo-estra-4y5 0)-diene-3, l-dione (49). A solution of silver perchlorate (0.55 g, 5 mole-eq) in acetone (2 ml) is added to a refluxing solution of monoadduct (48 0.28 g) in acetone (30 ml) containing water (0.5 ml). After being heated at reflux for 25 min the reaction mixture is cooled and the precipitated silver bromide is removed by filtration, yield about 0.11 g. The filtrate is diluted with water (500 ml) and is thoroughly extracted with chloroform. The chloroform extracts are washed with water and saturated salt solution, dried over anhydrous magnesium sulfate, and evaporated at... 

A-Homo-estra-, 4, )-triene-3, l-dione (50). A solution of bromo ketone (49 0.2 g), silver perchlorate (0.5 g) and 20% aqueous acetone (30 ml) is heated at reflux with stirring for 30 min and then allowed to cool to room temperature. The mixture is filtered to remove precipitated silver bromide (ca. 0.19 g) and the filtrate is diluted with water (200 ml) and then extracted with chloroform. The chloroform extracts are washed, successively with water, 5% sodium bicarbonate solution, water and saturated salt solution. After being dried over anhydrous magnesium sulfate, the solvents are removed at reduced pressure to give a solid. Recrystallization from ethyl acetate gives A-homo-estra-l,4,5(10)-triene-3,17-dione (50 0.17 g) mp 193-197°. 

After an additional 10 min, a 1 % solution of hydrochloric acid (100 ml) is slowly added to the stirred reaction mixture and the resultant mixture is transferred to a separatory funnel. The ether layer is separated and washed sequentially with water, 5 % sodium bicarbonate solution, water and saturated salt solution. The washed ether solution is dried over anhydrous sodium sulfate, filtered, and evaporated to give an oily residue (0.45 g). Chromatography of the crude product on silica gel (50 g) followed by crystallization of the solid thus obtained (0.18 g) from ethanol gives 3 -hydroxy-B-homo-cholest-5-en-7a-one acetate (67 0.14 g) mp 90-91° [a]o 99° (CHCI3). 

A solution of the crude cyanohydrin (94a ca. 1 g) in pyridine (15 ml) and acetic anhydride (15 ml) is allowed to stand at room temperature for 52 hr. The solvents are evaporated under reduced pressure below 60°. The residue is dissolved in ether, and the ether solution is washed successively with 5 % hydrochloric acid, water and saturated salt solution. The solvent is evaporated under reduced pressure to give a crystalline residue. Recrystallization of the crude product from cyclohexane-acetone gives 3-methoxy-17a-cyano-estra-l,3,5(10)-trien-17i5-ol acetate (94b 0.9 g), mp 130-132°, as large prisms. 

A solution of cholestane-5a,6a-diol 6-tosylate (115a, 0.15 g) in dimethylformamide (20 ml) containing calcium carbonate (0.2 g) is heated for 8 hr on a steam bath. The reaction mixture is then cooled, filtered and diluted with water. The mixture is extracted with ether and the ether extracts are washed with water and saturated salt solution, dried over anhydrous magnesium sulfate and evaporated to dryness under reduced pressure to give the A-homo-B-norketone (116a, 85 mg) mp 123-125° [a]j> 21° (CHCI3). 

With dinitriles a slightly different procedure is necessary due to their water solubility. After the reaction has cooled, 150 ml of chloroform is added to the flask, and this mixture is then poured into saturated salt solution. Enough water is added to dissolve precipitated salt and the chloroform layer is separated. The aqueous layer is extracted once with chloroform. The combined extracts are then washed twice with salt solution, dried, and distilled. 

To a suspension of 25.0 g of 11/3,17a,21-trihydroxy-6,16a-dimethyl-4,6-pregnadiene-3,20-dione in 1.5 liters of alcohol-free chloroform cooled to about 5°C in an ice bath is added with constant stirring 750 ml of cold, concentrated hydrochloric acid and then 750 ml of formalin (low in methanol). The mixture is removed from the ice bath and stirred at room temperature for 7 hours. The layers are separated and the aqueous phase is back-extracted twice with chloroform. The combined organic layers are washed twice with a 5% solution of sodium bicarbonate, and twice with a saturated salt solution. The solution is dried over magnesium sulfate and evaporated to dryness under reduced pressure. 

---