Water acetic acid

Figure 5-3. Enthalpy concentration diagram for acetic acid-water at 1.013 bar.

Xanthylamides. Dissolve 0 25 g. of xanthhydrol in 3-5 ml. of glacial acetic acid if an oil separates (as is sometimes the case with commercial material), allow to settle for a short time and decant the supernatant solution. Add 0-25 g. of the amide, shake and allow to stand. If a crystalline derivative does not separate in about 10 minutes, warm on a water bath for a period not exceeding 30 minutes, and allow to cool. Filter oflF the solid xanthylamide (9-acylamidoxanthen) and recrystallise it from dioxan - water or from acetic acid - water, dry at 80° for 15 minutes and determine the m.p. 

Method 2. Place 0-2 g. of cupric acetate, 10 g. of ammonium nitrate, 21 2 g. of benzoin and 70 ml. of an 80 per cent, by volume acetic acid -water solution in a 250 ml. flask fitted with a reflux condenser. Heat the mixture with occasional shaking (1). When solution occurs, a vigorous evolution of nitrogen is observed. Reflux for 90 minutes, cool the solution, seed the solution with a crystal of benzil (2), and allow to stand for 1 hour. Filter at the pump and keep the mother liquor (3) wash well with water and dry (preferably in an oven at 60°). The resulting benzil has m.p. 94-95° and the m.p. is unaffected by recrystallisation from alcohol or from carbon tetrachloride (2 ml. per gram). Dilution of the mother liquor with the aqueous washings gives a further 1 Og. of benzil (4). 

Added 112 grams sassafras oil. Shake for a couple of minutes. You get an orangish emulsion. Clears within 15 minutes forming two layers, bottom layer oil, top layer acetic acid, eugenol + the other solubles. Separated the oil from the others, washed the oil layer 2x with fresh C//-/2O. Weight after acetic acid water washes 101.5 (-10.5 grams). 

Acetic acid containing less than 1% water is called glacial. It is hygroscopic and the freezing point is a convenient way to determine purity (7). Water is nearly always present in far greater quantities than any other impurity. Table 1 shows the freezing points for acetic acid-water mixtures. 

Table 1. Acetic Acid—Water Freezing Points...

Acetic acid forms a monohydrate containing about 23% water thus the density of acetic acid-water mixtures goes through a maximum between ... 

Sodium acetate reacts with carbon dioxide in aqueous solution to produce acetic anhydride and sodium bicarbonate (49). Under suitable conditions, the sodium bicarbonate precipitates and can be removed by centrifugal separation. Presumably, the cold water solution can be extracted with an organic solvent, eg, chloroform or ethyl acetate, to furnish acetic anhydride. The half-life of aqueous acetic anhydride at 19°C is said to be no more than 1 h (2) and some other data suggests a 6 min half-life at 20°C (50). The free energy of acetic anhydride hydrolysis is given as —65.7 kJ/mol (—15.7 kcal/mol) (51) in water. In wet chloroform, an extractant for anhydride, the free energy of hydrolysis is strangely much lower, —50.0 kJ/mol (—12.0 kcal/mol) (51). Half-life of anhydride in moist chloroform maybe as much as 120 min. Ethyl acetate, chloroform, isooctane, and / -octane may have promise for extraction of acetic anhydride. Benzene extracts acetic anhydride from acetic acid—water solutions (52). 

The effluent from the reactor is a slurry of terephthaUc acid because it dissolves to a limited extent in almost all solvents, including the acetic acid—water solvent used here. This slurry passes through a surge vessel that operates at a lower pressure than the reactor. More terephthaUc acid crystallizes and the slurry is then ready to be processed at close to atmospheric conditions. The terephthaUc acid crystals are recovered by filtration, washed, dried, and conveyed to storage, from which they are in turn fed to the purification step. 

Acetic acid-water Pinched system Ethyl acetate, propyl acetate, diethyl ether, dichloroethane, butyl acetate ... 

Acetic acid-water-vinyl acetate Pinched, azeotropic system Self-entraining ... 

In a ternaty hqiiid-hqiiid system, such as the acetic acid-water-MIBK system, all three components are present in both liquid phases. At equilibrium the activity A° of any component is the same in both phases by definition [Eq. (15-6)]. 

FIG. 15-42 Extraction in Mixco columns, methyl isobutyl ketone-acetic acid-water (continuous), d, = 0.5 ft, Zj = 0..3.3.3 ft, X = flooded condition. To convert feet to meters, multiply by 0..34S to convert feet per hour to meters per hour, multiply by 0.3048. 

FIG. 15-51 Effect of reciprocating speed on HETS, o-xylene-acetic acid-water system. Lo and Pmchazka in Lo et al., p. 377.)... 

FIG. 15 53 Effect of pulsing on extraction in a packed column methyl isobutyl ketone-acetic acid-water (continuous). Tower diameter = 1.58 in, 27-in depth of V4-in Raschig rings. = Vc = 7.5 to 10. To convert inches to centimeters, multiply by 2.54. [Data of Chanhy, von Berg, and Wiegandt, Ind. Eng. Chem., 47, 1153 (1.9.55), with permission. ... 

Acids that are solids can be purified in this way, except that distillation is replaced by repeated crystallisation (preferable from at least two different solvents such as water, alcohol or aqueous alcohol, toluene, toluene/petroleum ether or acetic acid.) Water-insoluble acids can be partially purified by dissolution in N sodium hydroxide solution and precipitation with dilute mineral acid. If the acid is required to be free from sodium ions, then it is better to dissolve the acid in hot N ammonia, heat to ca 80°, adding slightly more than an equal volume of N formic acid and allowing to cool slowly for crystallisation. Any ammonia, formic acid or ammonium formate that adhere to the acid are removed when the acid is dried in a vacuum — they are volatile. The separation and purification of naturally occurring fatty acids, based on distillation, salt solubility and low temperature crystallisation, are described by K.S.Markley (Ed.), Fatty Acids, 2nd Edn, part 3, Chap. 20, Interscience, New York, 1964. 

Crystd from glacial acetic acid, acetic acid/water or ethanol. 

Separated from retinol by column chromatography on water-deactivated alumina with hexane containing a very small percentage of acetone. Also chromatographed on TLC silica gel G, using pet ether/isopropyl ether/acetic acid/water (180 20 2 5) or pet ether/acetonitrile/acetic acid/water (190 10 1 15) to develop the chromatogram. Then recrystd from propylene at low temperature. 

The product may be recrystallized from 1 2 acetic acid-water (about 8 ml./g.), but this process effects little improvement in melting point or color, even when activated carbon is used. 

The importance of solvent participation in the borderline mechanisms should be noted. Nucleophilic participation is minimized by high electronegativity, which reduces the Lewis basicity and polarizability of the solvent molecules. Trifluoroacetic acid and perfiuoro alcohols are among the least nucleophilic of the solvents used in solvolysis studies. These solvents are used to define the characteristics of reactions proceeding without nucleophilic solvent participation. Solvent nucleophilicity increases with the electron-donating capacity of the molecule. The order trifluoroacetic acid < trifluoroetha-nol <acetic acid < water < ethanol gives a qualitative indication of the trend in solvent nucleophilicity. More will be said about solvent nucleophilicity in Section 5.5. 

Dichloromethane — methanol — glacial acetic acid — water (50 + 50-1-25-1-10). 

Sorm" " found that when cholesterol acetate (67) is oxidized by chromic acid in acetic acid-water at 55°, crystalline keto seco-acid (69) is obtained in 25-30 % yield from the mother liquors after removal of successive crops of 7-ketocholesterol acetate (68). Reaction of keto acid (69) with benzoyl chloride in pyridine gives a dehydration product, shown" to be the )5-lactone... 

---