Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Verification tests

When new equipment is purchased or there is a change in the manufacturing site, qualification exercises are performed as part of the validation process. Qualification (installation qualification, operation qualification, and performance qualification) for any equipment or facility is an extreme process which involves testing, verification, and documentation to assure that the particular equipment or facility is per the specification and meets the appropriate standards as defined by vendor and required by manufacturing and engineering personnel [14]. [Pg.92]

Because of the importance of this furiously progressing work and the urgency of the escalating electrical energy crisis worldwide, a paper [22] describing our results was placed on a Department of Energy Website, (see Ref. 22). The paper was later moved to a restricted DOE site reserved for scientists, until such time as independent testing verification and independent replication is obtained, to assure a fully valid scientific experiment. [Pg.710]

Most dispensers use spin-on type filters, similar in appearance and construction to most common engine oil filters. Most use steel housings and paper filter element that are compatible with ethanol, but the glue used to fasten the element to the housing may not be compatible with ethanol. The filter manufacturer should be contacted to see whether they have tested their filters for compatibility with ethanol (a recommendation without testing verification should be looked upon skeptically). If there is doubt, dispenser filters having nylon filter elements and ethanol-compatible glue should prove compatible. [Pg.105]

Verification of test equipment calibration Verification of controls and indicators Computer control system testing Verification of sequence of operations Verification of major components operation Verification of alarms Power failure/recovery testing... [Pg.644]

Disclaimer As in all theoretical variable determinations, these equations presented for Du calculation are subject to field-test verification. Equations (4.14) and (4.16) are not presented as being infallible or able to predict accurately every case of particle size with a given medium viscosity. For example, a crude with a high asphaltene content should be field tested before a final design for construction is issued on the basis of these equations. Small asphaltene crude contents (less than 2%) were used in deriving Eq. (4.16). More tests are needed for foam-liquid separations. Readers and users of this criterion, can perhaps contribute more data, and I indeed solicit such contributions of better methods and data as you may discover. [Pg.145]

Application context of the tests (verification tests, compliance tests, and characterization tests). Most of the compliance tests applied to solidification/ stabilization waste are short term tests involving high liquid to solid ratios and which sometimes include crushing of the materials. Such tests are not appropriate to understanding leaching behavior or for the prediction of release from solidification/stabilization wastes. [Pg.174]

With current system improvements in development, a device that automatically detects, classifies with high probability, and extracts a sample which is diverted directly to an automatic rapid test verification system, all without operator intervention, will soon be commercially available. Combined with a suite of other chemical, toxin, and radiological real-time sensors and an integrated data analysis and alert response system, the ultimate water security system is quickly becoming a reality. [Pg.29]

Particle count test (Verification of cleanliness) All classes 6 months Dust particle counts to be carried out and printouts of results produced. No. of readings and positions of tests to be in accordance with ISO 14644-1 Annex B... [Pg.82]

In the following, we first briefly define testing, verification, calibration, and validation because many different, and sometimes even contradictory, definitions exist, and because we need these terms for our review and for comparing model types. Then we give an overview of the main types of population models that can be used for risk assessment, and present our review. [Pg.106]

General Finding 10. Testing, verification, and integration beyond the 1999 demonstration phase will be necessary... [Pg.93]

General Recommendation 1. If a decision is made to move forward with any of the ACWA technology packages, substantial additional testing, verification, and especially integration should be performed prior to full-scale implementation (see General Finding 10). [Pg.94]

General Finding 10. Testing, verification, and integration beyond the 1999 demonstration phase wiU be necessary because the scale-up of a process can present many unexpected challenges, and the ACWA demonstrations were limited in nature. [Pg.53]

But again, claims about such products are susceptible to industry scrutiny and independent test verification [3-3, 14-19, 14-21, 14-23, 14-24, 14-25[. [Pg.213]

At each distinct phase of the application software development cycle (including testing), verification confirms that the phase has been successfully completed. Verification is, in general, completed by a verification team that consists of one or more persons. [Pg.65]

Roper, M. (1993). Software testing A selected annotated bibliography, Software—Testing, Verification and Reliability 3(2), 135-157. [Pg.338]

B Accredited Lab tested 1 Occasionally components are tested by a EU Accredited Lab (DAR for Germany) and do not bear a type-approval mark. The lab accreditation certificate, test report, and test verification must be readily available. 2 The lab accreditation certificate and test verification is obtained by end-product manufacturer and placed into the technical file. It is also advisable to obtain a copy of the test report for review. Conditional acceptance (case by case)... [Pg.94]

Standard Proposal CEN TC193/SC1/WG11 N21 Adhesives for on-site assemhhng or restoration of timber structures. On-site acceptance testing. Verification of the adhesive joint s shear strength. European Committee for Standardization (CEN), Brussels (2003). [Pg.297]

Initial Testing - Verification of safety-reiated SSC flinctionaiity. 10.3... [Pg.228]

VI.29] SHIRAI, K., et al.. Integrity of cast iron cask against free drop test—Verification of brittle failure design criterion, Int. J. Radioact. Mater. Transp. 4 1 (1993) 5-13. [Pg.346]

Advanced design-implement experiences are technically challenging at several levels. The work includes design and implementation of student-developed components, as well as integration, testing, verification, and validation in conjunction with commercially available components or those developed by other students. The technical tasks involved are typically at a level that students might encounter in their professional careers. The need for both the technical knowledge and the skills outlined in the CDIO Syllabus increases as the complexity of the task becomes evident to students. [Pg.123]

System specific testing verification of aspects defined within the... [Pg.536]

Condenser chilling test verification of the system cooling rate, normally 2°C/min, by monitoring the temperature at the condensing coils during cooling from 0°C to —60°C (1). [Pg.539]

The development, test, verification and validation of the full variability language application program shall be in accordance with lEC 61508-3. [Pg.78]

It is recommended that the user have a basic knowledge of the manufacturer software development methods, development tools, configuration management processes, and testing verification and validation methods to ensure the programmable component quality and that all changes are documented against the component s functional specification. [Pg.189]

General requirements with testing verification and validation as per lEC 61508-3... [Pg.459]

Judgment that objectives and requirements are met For failure result, corrective actions Detailed recording Re-test/verification results. [Pg.461]

Bernardeschi, C., Pantechi, A., Gnesi, S. Model checking fault tolerant systems. Softw. Test., Verif. Reliab. 12(4), 251-275 (2002)... [Pg.206]

Li, B., Sun, X., Leung, H., Zhang, S. A survey of code-based change impact analysis techniques. Software Testing, Verification and Reliability 23, 613-646 (2012)... [Pg.454]

Holzmann, G. J. Smith, M. H. (2001). Software model checking extracting verification models from source code. Software Testing, Verification and Reliability 11(2) 65-79. [Pg.27]


See other pages where Verification tests is mentioned: [Pg.21]    [Pg.179]    [Pg.851]    [Pg.1558]    [Pg.467]    [Pg.104]    [Pg.106]    [Pg.297]    [Pg.64]    [Pg.59]    [Pg.119]    [Pg.285]    [Pg.635]    [Pg.73]    [Pg.85]    [Pg.672]   
See also in sourсe #XX -- [ Pg.1558 , Pg.1559 , Pg.1559 , Pg.1560 , Pg.1560 ]




SEARCH



Basic Principles for Verifications and Tests

Design testing and verification

Dielectrics test voltage verification

Laboratory-developed tests analytical verification

Testing and Verification

Testing product verification phase

Verification

Verification within testing

Verifications and Tests

© 2024 chempedia.info