Cracking, steam

The feedstock usually comes from catalytic cracking, sometimes from steam cracking. The reaction products are Cy-Cg isoparaffins. The byproducts are the C3-C4 n-paraffins which do not react. 

Properly speaking, steam cracking is not a refining process. A key petrochemical process, it has the purpose of producing ethylene, propylene, butadiene, butenes and aromatics (BTX) mainly from light fractions of crude oil (LPG, naphthas), but also from heavy fractions hydrotreated or not (paraffinic vacuum distillates, residue from hydrocracking HOC). 

Table 10.13 provides some characteristic data relative to the steam cracking process. 

Typical steam cracking feedstock composition and yields. 

In a single stage, without liquid recycle, the conversion can be optimized between 60 and 90%. The very paraffinic residue is used to make lubricant oil bases of high viscosity index in the range of 150 N to 350 N the residue can also be used as feedstock to steam cracking plants providing ethylene and propylene yields equal to those from paraffinic naphthas, or as additional feedstock to catalytic cracking units. 

With regard to the unconverted residue, the VI after dewaxing is 120 to 135 and the BMCI is between 10 and 15, which makes it an excellent feed for steam cracking units. 

Residue to lube oil plant, steam cracking plant, FCC... 

Pyrolysis gasoline is a by-product of the steam cracking of hydrocarbon feeds in ethylene crackers (see Ethylene). Pyrolysis gasoline typically contains about 50—70 wt % aromatics, of which roughly 50% is benzene, 30% is toluene, and 20% is mixed xylenes (which includes EB). 

ElexibiHty allows the operator to pick and choose the most attractive feedstock available at a given point in time. The steam-cracking process produces not only ethylene, but other products as weU, such as propylene, butadiene, butylenes (a mixture of monounsaturated C-4 hydrocarbons), aromatics, etc. With ethane feedstock, only minimal quantities of other products ate produced. As the feedstocks become heavier (ie, as measured by higher molecular weights and boiling points), increasing quantities of other products are produced. The values of these other coproduced products affect the economic attractiveness and hence the choice of feedstock. 

Petroleum resins are low molecular weight thermoplastic hydrocarbon resins synthesized from steam cracked petroleum distillates. These resins are differentiated from higher molecular weight polymers such as polyethylene and polypropylene, which are produced from essentially pure monomers. Petroleum resin feedstocks are composed of various reactive and nonreactive aliphatic and aromatic components. The resins are usually classified as C-5... 

The feedstocks used ia the production of petroleum resias are obtaiaed mainly from the low pressure vapor-phase cracking (steam cracking) and subsequent fractionation of petroleum distillates ranging from light naphthas to gas oil fractions, which typically boil ia the 20—450°C range (16). Obtaiaed from this process are feedstreams composed of atiphatic, aromatic, and cycloatiphatic olefins and diolefins, which are subsequently polymerized to yield resias of various compositioas and physical properties. Typically, feedstocks are divided iato atiphatic, cycloatiphatic, and aromatic streams. Table 2 illustrates the predominant olefinic hydrocarbons obtained from steam cracking processes for petroleum resia synthesis (18). 

Table 2. Unsaturated Monomers Obtained From Steam Cracking ...

Aliphatic C-5—C-6. Aliphatic feedstreams are typically composed of C-5 and C-6 paraffins, olefins, and diolefins, the main reactive components being piperylenes cis-[1574-41 -0] and /n j -l,3-pentadiene [2004-70-8f). Other main compounds iaclude substituted C-5 and C-6 olefins such as cyclopentene [142-29-OJ, 2-methyl-2-butene [513-35-9] and 2-methyl-2-pentene [625-27-4J. Isoprene and cyclopentadiene maybe present ia small to moderate quaatities (2—10%). Most steam cracking operatioas are desigaed to remove and purify isoprene from the C-5—C-6 fraction for applications ia mbbers and thermoplastic elastomers. Cyclopentadiene is typically dimerized to dicyclopentadiene (DCPD) and removed from C-5 olefin—diolefin feedstreams duriag fractionation (19). 

Cycloaliphatic Diene CPD—DCPD. Cycloatiphatic diene-based hydrocarbon resias are typically produced from the thermal or catalytic polymerization of cyclopeatadieae (CPD) and dicyclopentadiene (DCPD). Upon controlled heating, CPD may be dimerized to DCPD or cracked back to the monomer. The heat of cracking for DCPD is 24.6 kJ / mol (5.88 kcal/mol). In steam cracking processes, CPD is removed from C-5 and... 

Aromatic. Aromatic feedstreams (C-8, C-9, C-10) derived from the steam cracking of petroleum distillates are composed of styrene, iadene, vinyltoluenes (eg, meta- and i ra-methylstyrene), and their respective alkylated analogues. A typical aromatic feedstream might contain 50% reactive olefins with the remainder being alkylated benzenes and higher aromatics. 

Gyclopentadiene/Dicyclopentadiene-Based Petroleum Resins. 1,3-Cyclopentadiene (CPD) is just one of the numerous compounds produced by the steam cracking of petroleum distillates. Due to the fact that DCPD is polymerized relatively easily under thermal conditions without added catalyst, resins produced from cycloaHphatic dienes have become a significant focus of the hydrocarbon resin industry. 

In order to increase the solubiUty parameter of CPD-based resins, vinyl aromatic compounds, as well as other polar monomers, have been copolymerized with CPD. Indene and styrene are two common aromatic streams used to modify cyclodiene-based resins. They may be used as pure monomers or contained in aromatic steam cracked petroleum fractions. Addition of indene at the expense of DCPD in a thermal polymerization has been found to lower the yield and softening point of the resin (55). CompatibiUty of a resin with ethylene—vinyl acetate (EVA) copolymers, which are used in hot melt adhesive appHcations, may be improved by the copolymerization of aromatic monomers with CPD. As with other thermally polymerized CPD-based resins, aromatic modified thermal resins may be hydrogenated. 

IFP Process for 1-Butene from Ethylene. 1-Butene is widely used as a comonomer in the production of polyethylene, accounting for over 107,000 t in 1992 and 40% of the total comonomer used. About 60% of the 1-butene produced comes from steam cracking and fluid catalytic cracker effluents (10). This 1-butene is typically produced from by-product raffinate from methyl tert-huty ether production. The recovery of 1-butene from these streams is typically expensive and requires the use of large plants to be economical. Institut Francais du Petrole (IFP) has developed and patented the Alphabutol process which produces 1-butene by selectively dimerizing ethylene. 

Petroleum-derived benzene is commercially produced by reforming and separation, thermal or catalytic dealkylation of toluene, and disproportionation. Benzene is also obtained from pyrolysis gasoline formed ia the steam cracking of olefins (35). 

The pattern of commercial production of 1,3-butadiene parallels the overall development of the petrochemical industry. Since its discovery via pyrolysis of various organic materials, butadiene has been manufactured from acetylene as weU as ethanol, both via butanediols (1,3- and 1,4-) as intermediates (see Acetylene-DERIVED chemicals). On a global basis, the importance of these processes has decreased substantially because of the increasing production of butadiene from petroleum sources. China and India stiU convert ethanol to butadiene using the two-step process while Poland and the former USSR use a one-step process (229,230). In the past butadiene also was produced by the dehydrogenation of / -butane and oxydehydrogenation of / -butenes. However, butadiene is now primarily produced as a by-product in the steam cracking of hydrocarbon streams to produce ethylene. Except under market dislocation situations, butadiene is almost exclusively manufactured by this process in the United States, Western Europe, and Japan. 

Table 4. Product Distribution from Steam Cracking Various Feedstocks ...

Since the bulk of butadiene is recovered from steam crackers, its economics is very sensitive to the selection of feedstocks, operating conditions, and demand patterns. Butadiene supply and, ultimately, its price are strongly influenced by the demand for ethylene, the primary product from steam cracking. Currently there is a worldwide surplus of butadiene. Announcements of a number of new ethylene plants will likely result in additional butadiene production, more than enough to meet worldwide demand for polymers and other chemicals. When butadiene is in excess supply, ethylene manufacturers can recycle the butadiene as a feedstock for ethylene manufacture. 

Butylene yield Gas oil Residue Delayed coking Elexicoking Steam cracking of naphtha... 

Steam Cracking. Steam cracking is a nonselective process that produces many products from a variety of feedstocks by free-radical reactions. An excellent treatise on the fundamentals of manufacturing ethylene has been given (44). Eeedstocks range from ethane on the light end to heavy vacuum gas oil on the heavy end. All produce the same product slate but in different amounts depending on the feedstock. 

Significant products from a typical steam cracker are ethylene, propylene, butadiene, and pyrolysis gasoline. Typical wt % yields for butylenes from a steam cracker for different feedstocks are ethane, 0.3 propane, 1.2 50% ethane/50% propane mixture, 0.8 butane, 2.8 hill-range naphtha, 7.3 light gas oil, 4.3. A typical steam cracking plant cracks a mixture of feedstocks that results in butylenes yields of about 1% to 4%. These yields can be increased by almost 50% if cracking severity is lowered to maximize propylene production instead of ethylene. 

The principal sources of feedstocks in the United States are the decant oils from petroleum refining operations. These are clarified heavy distillates from the catalytic cracking of gas oils. About 95% of U.S. feedstock use is decant oil. Another source of feedstock is ethylene process tars obtained as the heavy byproducts from the production of ethylene by steam cracking of alkanes, naphthas, and gas oils. There is a wide use of these feedstocks in European production. European and Asian operations also use significant quantities of coal tars, creosote oils, and anthracene oils, the distillates from the high temperature coking of coal. European feedstock sources are 50% decant oils and 50% ethylene tars and creosote oils. 

Rhodium catalyst is used to convert linear alpha-olefins to heptanoic and pelargonic acids (see Carboxylic acids, manufacture). These acids can also be made from the ozonolysis of oleic acid, as done by the Henkel Corp. Emery Group, or by steam cracking methyl ricinoleate, a by-product of the manufacture of nylon-11, an Atochem process in France (4). Neoacids are derived from isobutylene and nonene (4) (see Carboxylic acids, trialkylacetic acids). 

---