Polypropylene Vinyl Acetate

Tang et al. [174] found that the tensile modulus of polypropylene-vinyl acetate copolymer increased with an increase of calcium carbonate filler weight fraction, and that the impact strength decreased rapidly when the weight fraction of calcium 

Mechanical Properties of Virgin and 20% Calcium Carbonate-Filled Polypropylene 

Liang [171] also observed this effect in the case of low-density polyethylene composites. 

---

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

Other Films. Although commercially less important than polyethylenes and polypropylenes, a number of other plastic films are in commercial use or development for special appHcations, including ethylene—vinyl acetate, ionomer, and polyacrylonitrile [25014-41-9]. 

Polymer Blends. The miscibility of poly(ethylene oxide) with a number of other polymers has been studied, eg, with poly (methyl methacrylate) (18—23), poly(vinyl acetate) (24—27), polyvinylpyrroHdinone (28), nylon (29), poly(vinyl alcohol) (30), phenoxy resins (31), cellulose (32), cellulose ethers (33), poly(vinyl chloride) (34), poly(lactic acid) (35), poly(hydroxybutyrate) (36), poly(acryhc acid) (37), polypropylene (38), and polyethylene (39). 

Carbon Cha.in Backbone Polymers. These polymers may be represented by (4) and considered derivatives of polyethylene, where n is the degree of polymeriza tion and R is (an alkyl group or) a functional group hydrogen (polyethylene), methyl (polypropylene), carboxyl (poly(acryhc acid)), chlorine (poly(vinyl chloride)), phenyl (polystyrene) hydroxyl (poly(vinyl alcohol)), ester (poly(vinyl acetate)), nitrile (polyacrylonitrile), vinyl (polybutadiene), etc. The functional groups and the molecular weight of the polymers, control thek properties which vary in hydrophobicity, solubiUty characteristics, glass-transition temperature, and crystallinity. 

The use of TAG as a curing agent continues to grow for polyolefins and olefin copolymer plastics and mbbers. Examples include polyethylene (109), chlorosulfonated polyethylene (110), polypropylene (111), ethylene—vinyl acetate (112), ethylene—propylene copolymer (113), acrylonitrile copolymers (114), and methylstyrene polymers (115). In ethylene—propylene copolymer mbber compositions. TAG has been used for injection molding of fenders (116). Unsaturated elastomers, such as EPDM, cross link with TAG by hydrogen abstraction and addition to double bonds in the presence of peroxyketal catalysts (117) (see Elastol rs, synthetic). 

Problems with grafting and morphological changes in the particles are reviewed (117). Vinyl acetate has been grafted onto atactic polypropylene (118) and casein (119). 

Tile is based mainly on vinyl chloride and vinyl acetate copolymers. Some polypropylene tile systems have recendy been iatroduced. A petroleum resia is usually employed as an extender and processiag aid conventional vinyl plasticizers and stabilizers also are iacorporated. Reinforcing fibers and limestone constitute the remainder of the tile composition the fibers contribute hot strength for processiag and dimensional stabiHty ia the finished tile, limestone suppHes bulk at an economical cost. Stable pigments are also iacorporated. Siace tile is iastalled oa and below grade level, it is important that the finished product be resistant to the effects of moisture and alkaH. 

Extension of the chlorosulfonation technology to base resins other than polyethylene, where value can be added, seems a logical next step. Polypropylene and ethylene copolymers containing additional functionaUty, ie, maleic anhydride graft, vinyl acetate, acrylic acid, etc, have been chlorinated and chlorosulfonated to broaden the appHcation base, particularly in coatings and adhesives (9,10). 

If polypropylene is too hard for the purpose envisaged, then the user should consider, progressively, polyethylene, ethylene-vinyl acetate and plasticised PVC. If more rubberiness is required, then a vulcanising rubber such as natural rubber or SBR or a thermoplastic polyolefin elastomer may be considered. If the material requires to be rubbery and oil and/or heat resistant, vulcanising rubbers such as the polychloroprenes, nitrile rubbers, acrylic rubbers or hydrin rubbers or a thermoplastic elastomer such as a thermoplastic polyester elastomer, thermoplastic polyurethane elastomer or thermoplastic polyamide elastomer may be considered. Where it is important that the elastomer remain rubbery at very low temperatures, then NR, SBR, BR or TPO rubbers may be considered where oil resistance is not a consideration. If, however, oil resistance is important, a polypropylene oxide or hydrin rubber may be preferred. Where a wide temperature service range is paramount, a silicone rubber may be indicated. The selection of rubbery materials has been dealt with by the author elsewhere. ... 

Specialty waxes include polar waxes for more polar adhesive systems. Examples would be castor wax (triglyceride of 12-hydroxy stearic acid) or Paracin wax N- 2 hydroxy ethyl)-12-hydroxy stearamide) which are used in polyester, polyamide, or with high VA EVA copolymer-based systems. Other common polar waxes are maleated polyethylenes, which are used to improve the specific adhesion of polyethylene-based adhesives, and low molecular weight ethylene copolymers with vinyl acetate or acrylic acid, which are used to improve low temperature adhesion. High melting point isotactic polypropylene wax (7 155°C) and highly refined paraffin wax (7,n 83°C) are used where maximum heat resistance is critical. Needless to say, these specialty waxes also command a premium price, ranging from 2 to 5 times that of conventional paraffin wax. 

Poly(ethylene terephtlhalate) Phenol-formaldehyde Polyimide Polyisobutylene Poly(methyl methacrylate), acrylic Poly-4-methylpentene-1 Polyoxymethylene polyformaldehyde, acetal Polypropylene Polyphenylene ether Polyphenylene oxide Poly(phenylene sulphide) Poly(phenylene sulphone) Polystyrene Polysulfone Polytetrafluoroethylene Polyurethane Poly(vinyl acetate) Poly(vinyl alcohol) Poly(vinyl butyral) Poly(vinyl chloride) Poly(vinylidene chloride) Poly(vinylidene fluoride) Poly(vinyl formal) Polyvinylcarbazole Styrene Acrylonitrile Styrene butadiene rubber Styrene-butadiene-styrene Urea-formaldehyde Unsaturated polyester... 

It has been found that, for a fixed mineral filler content, the viscosity of PMF-based composites increases when the coat is made of polyethylene [164, 209, 293], poly(vinyl chloride) [316] and polypropylene [326, 327], The picture was different, however, for composites based on the ethylene/vinyl acetate copolymer to which kaolin with grafted poly (vinyl acetate) was added [336]. Addition of PMF with a minimum quantity of grafted polymer results in a sharp drop of flowability (rise of viscosity), in comparison to addition of unmodified filler but with a further increase of the quantity of grafted polymer the flow gradually increases and, depending on the kaolin content and quantity of grafted polymer, may even become higher than in specimens with unmodified filler, for equal concentrations. 

Blend of polypropylene and ethylene vinyl acetate copolymer... 

Aluminum foil Polypropylene—ethylene vinyl acetate 0.9... 

Chattopadhyay S., Chaki T.K., and Bhowmick A.K., New thermoplastic elastomers from poly(ethyle-neoctene) (engage), poly(ethylene-vinyl acetate) and low-density polyethylene by electron beam technology structural characterization and mechanical properties. Rubber Chem. TechnoL, 74, 815, 2001. Roy Choudhury N. and Dutta N.K., Thermoplastic elastomeric natural rubber-polypropylene blends with reference to interaction between the components. Advances in Polymer Blends and Alloys Technology, Vol. 5 (K. Finlayson, ed.), Technomic Publishers, Pensylvania, 1994, 161. 

Waters Seawater (National Research Council Canada 1992) was collected in the North Atlantic Ocean at a depth of 10 m, 35 km southeast of Hahfax, Nova Scotia, Canada. The water was peristaltically pumped through cleaned polyethylene-hned ethyl vinyl acetate tubing and 0.45-pm acrylic copolymer filters. It was acidified to pH 1.6 with ultrapure nitric acid during its immediate transfer to 50-L acid-leached polypropylene carboys, previously conditioned with ultrapure water acidified to pH 1.6. The seawater was later homogenized in two linked 800-L polyethylene tanks in a clean room and immediately bottled in cleaned 2-L polyethylene bottles. Randomly selected bottles were used for analytical measurements. 

We can divide commodity plastics into two classes excellent and moderate insulators. Polymers that have negligible polar character, typically those containing only carbon-carbon and carbon-hydrogen bonds, fall into the first class. This group includes polyethylene, polypropylene, and polystyrene. Polymers made from polar monomers are typically modest insulators, due to the interaction of their dipoles with electrical fields. We can further divide moderate insulators into those that have dipoles that involve backbone atoms, such as polyvinyl chloride and polyamides, and those with polar bonds remote from the backbone, such as poly(methyl methacrylate) and poly(vinyl acetate). Dipoles involving backbone atoms are less susceptible to alignment with an electrical field than those remote from the backbone. 

Hot melt adhesives based on poly(3HB-co-3HV) have also been described [119]. Hot melts are commonly used in bookbinding, bag ending and case and carton sealing and are mostly based on synthetic materials such as polyethylene, polypropylene ethylene-vinyl acetate and styrene block copolymers [119]. Hot melts based on PHAs alleviate the dependence on petroleum based materials and allow the development of biodegradable alternatives based on natural raw materials. 

Vinyl polymers [polystyrene, PVC, polyethylene, polypropylene, poly(vinyl acetate), poly(vinyl alcohol), polyacrylonitrile] -1920 Packaging, tubing, household goods, records, carpets, toys, water based paint, adhesives, varnishes Phthalate esters, poly(vinyl alcohol) ... 

The most current method of nitroglycerin application is a transdermal device or skin patch. A cross section of such a patch is illustrated in Figure 6. The patch is actually a multi-layered polymer stack. The semipermeable membrane which comes in contact with the skin is usually composed of an ethylene-vinyl acetate copolymer or polypropylene. The reservoir contains the drug in a hydrogel or polymer matrix or solvent (the material must be chosen to insure uniform delivery). Examples of some solvents used include dimethyl sulfoxide (DMSO), sodium lauryl sulfate (SDS - a detergent) and propylene glycol/oleic acid. 

Many dialkyl and diaryl cadmium compounds have found use as polymerization catalysts. For example, the diethyl compound catalyzes polymerization of vinyl chloride, vinyl acetate, and methyl methacrylate (45), and when mixed with TiCl can be used to produce polyethylene and crystalline polypropylene for filaments, textiles, glues, and coatings (45). With >50% TiCl diethyl cadmium polymerizes dienes. Diethyl cadmium maybe used as an intermediate ethylating agent in the production of tetraethyllead. The diaryl compounds such as diphenylcadmium [2674-04-6]> (C H Cd, (mp 174°C) are also polymerization catalysts. These compounds are also prepared using Grignard or arylUthium reagents in tetrahydrofiiran (THF) solvent but may be prepared by direct metal substitution reactions such as ... 

Systems in which a polyolefin is the binder have attracted world-wide attention. These include the polyethylene—phenolic microsphere 74,115>, polyethylene or polypropylene—glass microsphere114116), polyethylene or polybutylene—PVC microsphere (containing isobutane)52), and polyethylene/vinyl acetate copolymer—glass microsphere11 systems. Syntactic foams have been made from polystyrene (and its copolymers with chlorostyrene or polychlorostyrene) and microspheres made from polyethylene or polypropylene46115 and foams from styrene/acrylonitrile 1171... 

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... 

---