Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Polybutadiene production

Although it was difficult to detect structural characteristics other than those of PVC in a polybutadiene-PVC reaction product containing less than 5% polybutadiene, products containing 5-10% polybutadiene were shown to contain cis-1,4 unsaturation by infrared spectroscopic analysis. [Pg.321]

A flow scheme of m-1,4-polybutadiene production involving polymerisation with cobalt-based Ziegler-Natta catalysts in a solution process with the removal of catalyst residues from the polymer is presented in Figure 5.13 [227]. [Pg.319]

Figure 5.13 Flow scheme of polybutadiene production using the lowered-temperature solution polymerisation process... Figure 5.13 Flow scheme of polybutadiene production using the lowered-temperature solution polymerisation process...
Nasirov, F.A. Bi-functional nickel- or cobalt-containing catalyst-stabilizers for polybutadiene production and stabilization. Iranian Polym. J. 2003, 12, 111. [Pg.2272]

Knauf, T.F. Osman, A. Process for cis-Polybutadiene Production with Reduced Gel Formation. U.S. Patent 5,397,851,, Mar 14, 1995 Polysar Rubber. [Pg.2273]

Aminoxy chain-end-functionalized polybutadienes have been prepared by the reactions of PBDLi with halogen-containing benzyloxyamines. PBDLi (Mn = 990gmor, Mw/Mn=1.04) in heptane was reacted with 2,2,6,6-tetra-methyl-l-(2-bromo-l-phenylethoxy)piperidine at -78 °C as shown in eqn [33]. When this reaction was effected at room temperature, 73% of a dimeric polybutadiene product was obtained no dimeric product was observed when the reaction was carried out at -78 °C. The H NMR... [Pg.373]

Anionic Polymerization. Complementing the diversity in microstructure inherent to anionic chemistry, living anionic polymerization based on alkali metal alkyl initiating systems can also afford a wide range of macrostructural possibilities for polybutadiene products. [Pg.870]

The economics of polybutadiene production are characterized by overcapacity on a global basis. Total world capacity increased by 649,000 t from 1995 to 1999 however, actual production increased by only 167,000 t during this same period... [Pg.885]

Emulsifiers for polybutadiene production United States 3,476,735 1969 Farbenfabriken Bayer A.G. [Pg.561]

Epichlorohydrin is a product of covulcanization of epichlorohydrin (epoxy) polymers with rubbers, especially di-polybutadiene. [Pg.1063]

Elastomers. Elastomers are polymers or copolymers of hydrocarbons (see Elastomers, synthetic Rubber, natural). Natural mbber is essentially polyisoprene, whereas the most common synthetic mbber is a styrene—butadiene copolymer. Moreover, nearly all synthetic mbber is reinforced with carbon black, itself produced by partial oxidation of heavy hydrocarbons. Table 10 gives U.S. elastomer production for 1991. The two most important elastomers, styrene—butadiene mbber (qv) and polybutadiene mbber, are used primarily in automobile tires. [Pg.369]

Catalysts. Iodine and its compounds ate very active catalysts for many reactions (133). The principal use is in the production of synthetic mbber via Ziegler-Natta catalysts systems. Also, iodine and certain iodides, eg, titanium tetraiodide [7720-83-4], are employed for producing stereospecific polymers, such as polybutadiene mbber (134) about 75% of the iodine consumed in catalysts is assumed to be used for polybutadiene and polyisoprene polymeri2a tion (66) (see RUBBER CHEMICALS). Hydrogen iodide is used as a catalyst in the manufacture of acetic acid from methanol (66). A 99% yield as acetic acid has been reported. In the heat stabiH2ation of nylon suitable for tire cordage, iodine is used in a system involving copper acetate or borate, and potassium iodide (66) (see Tire cords). [Pg.366]

Acrylonitrile—Butadiene—Styrene. ABS is an important commercial polymer, with numerous apphcations. In the late 1950s, ABS was produced by emulsion grafting of styrene-acrylonitrile copolymers onto polybutadiene latex particles. This method continues to be the basis for a considerable volume of ABS manufacture. More recently, ABS has also been produced by continuous mass and mass-suspension processes (237). The various products may be mechanically blended for optimizing properties and cost. Brittle SAN, toughened by SAN-grafted ethylene—propylene and acrylate mbbets, is used in outdoor apphcations. Flame retardancy of ABS is improved by chlorinated PE and other flame-retarding additives (237). [Pg.419]

Pyrotechnic mixtures may also contain additional components that are added to modify the bum rate, enhance the pyrotechnic effect, or serve as a binder to maintain the homogeneity of the blended mixture and provide mechanical strength when the composition is pressed or consoHdated into a tube or other container. These additional components may also function as oxidizers or fuels in the composition, and it can be anticipated that the heat output, bum rate, and ignition sensitivity may all be affected by the addition of another component to a pyrotechnic composition. An example of an additional component is the use of a catalyst, such as iron oxide, to enhance the decomposition rate of ammonium perchlorate. Diatomaceous earth or coarse sawdust may be used to slow up the bum rate of a composition, or magnesium carbonate (an acid neutralizer) may be added to help stabilize mixtures that contain an acid-sensitive component such as potassium chlorate. Binders include such materials as dextrin (partially hydrolyzed starch), various gums, and assorted polymers such as poly(vinyl alcohol), epoxies, and polyesters. Polybutadiene mbber binders are widely used as fuels and binders in the soHd propellant industry. The production of colored flames is enhanced by the presence of chlorine atoms in the pyrotechnic flame, so chlorine donors such as poly(vinyl chloride) or chlorinated mbber are often added to color-producing compositions, where they also serve as fuels. [Pg.347]

In the late 1920s Bayer Company began reevaluating the emulsion polymerisation process of polybutadiene as an improvement over their Buna technology, which was based on sodium as a catalyst. Incorporation of styrene (qv) as a comonomer produced a superior polymer compared to polybutadiene. The product Buna S was the precursor of the single largest-volume polymer produced in the 1990s, emulsion styrene—butadiene mbber... [Pg.493]

Homopolymerization of butadiene can proceed via 1,2- or 1,4-additions. The 1,4-addition produces the geometrically distinguishable trans or cis stmctures with internal double bonds on the polymer chains, 1,2-Addition, on the other hand, yields either atactic, isotactic, or syndiotactic polymer stmctures with pendent vinyl groups (Eig. 2). Commercial production of these polymers started in 1960 in the United States. Eirestone and Goodyear account for more than 60% of the current production capacity (see Elastomers, synthetic-polybutadiene). [Pg.345]

The economic importance of copolymers can be cleady illustrated by a comparison of U.S. production of various homopolymer and copolymer elastomers and resins (102). Figure 5 shows the relative contribution of elastomeric copolymers (SBR, ethylene—propylene, nitrile mbber) and elastomeric homopolymers (polybutadiene, polyisoprene) to the total production of synthetic elastomers. Clearly, SBR, a random copolymer, constitutes the bulk of the entire U.S. production. Copolymers of ethylene and propylene, and nitrile mbber (a random copolymer of butadiene and acrylonitrile) are manufactured in smaller quantities. Nevertheless, the latter copolymers approach the volume of elastomeric butadiene homopolymers. [Pg.187]

Fig. 5. U.S. production of synthetic elastomers (thousands of metric tons) versus production year (63). A, Total B, SBR C, polybutadiene D,... Fig. 5. U.S. production of synthetic elastomers (thousands of metric tons) versus production year (63). A, Total B, SBR C, polybutadiene D,...
This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. [Pg.516]

Commercially, anionic polymerization is limited to three monomers styrene, butadiene, and isoprene [78-79-5], therefore only two useful A—B—A block copolymers, S—B—S and S—I—S, can be produced direcdy. In both cases, the elastomer segments contain double bonds which are reactive and limit the stabhity of the product. To improve stabhity, the polybutadiene mid-segment can be polymerized as a random mixture of two stmctural forms, the 1,4 and 1,2 isomers, by addition of an inert polar material to the polymerization solvent ethers and amines have been suggested for this purpose (46). Upon hydrogenation, these isomers give a copolymer of ethylene and butylene. [Pg.15]

A large volume usage of S—B—S-based compounds is ia footwear. Canvas footwear, such as sneakers and unit soles, can be made by injection mol ding. Frictional properties resemble those of conventionally vulcanised mbbers and are superior to those of the flexible thermoplastics, such as plasticized poly(vinyl chloride). The products remain flexible under cold conditions because of the good low temperature properties of the polybutadiene segment. [Pg.18]

Rubber and Elastomers Rubber and elastomers are widely used as lining materials. To meet the demands of the chemical indus-tiy, rubber processors are continually improving their products. A number of synthetic rubbers have been developed, and while none has all the properties of natural rubber, they are superior in one or more ways. The isoprene and polybutadiene synthetic rubbers are duphcates of natural. [Pg.2461]


See other pages where Polybutadiene production is mentioned: [Pg.205]    [Pg.310]    [Pg.878]    [Pg.880]    [Pg.883]    [Pg.884]    [Pg.54]    [Pg.300]    [Pg.205]    [Pg.310]    [Pg.878]    [Pg.880]    [Pg.883]    [Pg.884]    [Pg.54]    [Pg.300]    [Pg.70]    [Pg.70]    [Pg.394]    [Pg.202]    [Pg.317]    [Pg.419]    [Pg.246]    [Pg.252]    [Pg.257]    [Pg.522]    [Pg.467]    [Pg.467]    [Pg.468]    [Pg.530]    [Pg.5]    [Pg.7]    [Pg.190]   
See also in sourсe #XX -- [ Pg.353 ]

See also in sourсe #XX -- [ Pg.2261 ]




SEARCH



Polybutadiene Ziegler-Natta products

Polybutadiene monomer production

Polybutadiene polymer production

© 2024 chempedia.info