Styrene copolymers acrylonitrile

Styrene-acrylonitrile copolymer Styrene- butadiene copolymer, high-impact Polysulfone ... 

Thermal Oxidative Stability. ABS undergoes autoxidation and the kinetic features of the oxygen consumption reaction are consistent with an autocatalytic free-radical chain mechanism. Comparisons of the rate of oxidation of ABS with that of polybutadiene and styrene—acrylonitrile copolymer indicate that the polybutadiene component is significantly more sensitive to oxidation than the thermoplastic component (31—33). Oxidation of polybutadiene under these conditions results in embrittlement of the mbber because of cross-linking such embrittlement of the elastomer in ABS results in the loss of impact resistance. Studies have also indicated that oxidation causes detachment of the grafted styrene—acrylonitrile copolymer from the elastomer which contributes to impact deterioration (34). 

Examination of oven-aged samples has demonstrated that substantial degradation is limited to the outer surface (34), ie, the oxidation process is diffusion limited. Consistent with this conclusion is the observation that oxidation rates are dependent on sample thickness (32). Impact property measurements by high speed puncture tests have shown that the critical thickness of the degraded layer at which surface fracture changes from ductile to brittle is about 0.2 mm. Removal of the degraded layer restores ductiHty (34). Effects of embrittled surface thickness on impact have been studied using ABS coated with styrene—acrylonitrile copolymer (35). 

In all manufacturing processes, grafting is achieved by the free-radical copolymerization of styrene and acrylonitrile monomers in the presence of an elastomer. Ungrafted styrene—acrylonitrile copolymer is formed during graft polymerization and/or added afterward. 

In addition to graft copolymer attached to the mbber particle surface, the formation of styrene—acrylonitrile copolymer occluded within the mbber particle may occur. The mechanism and extent of occluded polymer formation depends on the manufacturing process. The factors affecting occlusion formation in bulk (77) and emulsion processes (78) have been described. The use of block copolymers of styrene and butadiene in bulk systems can control particle size and give rise to unusual particle morphologies (eg, coil, rod, capsule, cellular) (77). 

Many cellular plastics that have not reached significant commercial use have been introduced or their manufacture described in Hterature. Examples of such polymers are chlorinated or chlorosulfonated polyethylene, a copolymer of vinyUdene fluoride and hexafluoropropylene, polyamides (4), polytetrafluoroethylene (5), styrene—acrylonitrile copolymers (6,7), polyimides (8), and ethylene—propylene copolymers (9). 

Other Polymers. Besides polycarbonates, poly(methyl methacrylate)s, cycfic polyolefins, and uv-curable cross-linked polymers, a host of other polymers have been examined for their suitabiUty as substrate materials for optical data storage, preferably compact disks, in the last years. These polymers have not gained commercial importance polystyrene (PS), poly(vinyl chloride) (PVC), cellulose acetobutyrate (CAB), bis(diallylpolycarbonate) (BDPC), poly(ethylene terephthalate) (PET), styrene—acrylonitrile copolymers (SAN), poly(vinyl acetate) (PVAC), and for substrates with high resistance to heat softening, polysulfones (PSU) and polyimides (PI). 

Fig. 4. Miscibihty map for blends of styrene—acrylonitrile copolymers (SAN), with styrene—maleic anhydride copolymers (SMA).

Fig. 5. Phase behavior of blends of a styrene—acrylonitrile copolymer containing 19 wt % of acrylonitrile with other SAN copolymers of varying AN content and as a function of the molecular weight of the two copolymers (° ) one-phase mixture ( ) two-phase mixtures as judged by optical clarity. Curve...

Acrylonitrile—Butadiene—Styrene. ABS is an important commercial polymer, with numerous apphcations. In the late 1950s, ABS was produced by emulsion grafting of styrene-acrylonitrile copolymers onto polybutadiene latex particles. This method continues to be the basis for a considerable volume of ABS manufacture. More recently, ABS has also been produced by continuous mass and mass-suspension processes (237). The various products may be mechanically blended for optimizing properties and cost. Brittle SAN, toughened by SAN-grafted ethylene—propylene and acrylate mbbets, is used in outdoor apphcations. Flame retardancy of ABS is improved by chlorinated PE and other flame-retarding additives (237). 

The valuable characteristics of polyblends, two-phase mixtures of polymers in different states of aggregation, were also discussed in the previous chapter. This technique has been widely used to improve the toughness of rigid amorphous polymers such as PVC, polystyrene, and styrene-acrylonitrile copolymers. 

In addition to polystyrene and high-impact polystyrene there are other important styrene-based plastics. Most important of these is ABS, with a global capacity of about 5 X 10 t.p.a. and production of about 3 X 10 t.p.a. The styrenic PPO materials reviewed in Chapter 21 have capaeity and production figures about one-tenth those for ABS. Data for the more specialised styrene-acrylonitrile copolymers are difficult to obtain but consumption estimates for Western Europe in the early 1990s were a little over 60000 t.p.a. 

The important features of rigidity and transparency make the material competitive with polystyrene, cellulose acetate and poly(methyl methacrylate) for a number of applications. In general the copolymer is cheaper than poly(methyl methacrylate) and cellulose acetate, tougher than poly(methyl methacrylate) and polystyrene and superior in chemical and most physical properties to polystyrene and cellulose acetate. It does not have such a high transparency or such food weathering properties as poly(methyl methacrylate). As a result of these considerations the styrene-acrylonitrile copolymers have found applications for dials, knobs and covers for domestic appliances, electrical equipment and car equipment, for picnic ware and housewares, and a number of other industrial and domestic applications with requirements somewhat more stringent than can be met by polystyrene. 

Although tough enough for many uses, styrene-acrylonitrile copolymers are inadequate in this respect for other purposes. As a consequence, a range of... 

To produce the Type 2 polymers, styrene and acrylonitrile are added to polybutadiene latex and the mixture warmed to about 50°C to allow absorption of the monomers. A water-soluble initiator such as potassium persulphate is then added to polymerise the styrene and acrylonitrile. The resultant materials will be a mixture of polybutadiene, polybutadiene grafted with acrylonitrile and styrene, and styrene-acrylonitrile copolymer. The presence of graft polymer is essential since straightforwsird mixtures of polybutadiene and styrene-acrylonitrile copolymers are weak. In addition to emulsion processes such as those described above, mass and mass/suspension processes are also of importance. 

Janarthanan et al. [67] have employed roughness on a micron scale to enhance the adhesion between two immiscible polymers, polycarbonate and styrene-acrylonitrile copolymer, SAN. Grooves of depths between 5 and 35 p,m were scribed in the polycarbonate surface before laminating the two polymers. The... 

When the physical modification method is used, PS is modified by mechanical stirring with various synthetic rubbers such as polybutadiene, polybutadiene styrene, polyisopropene, polychloropropene, polybutadiene styrene-acrylonitrile copolymers. In the chemical modification, PS is modified with polyfunctional modificators in the presence of cationic catalysis. 

In the late 1940s, the demand for styrene homopolymers (PS) and styrene-acrylonitrile copolymers (SAN) was drastically reduced due to their inherent brittleness. Thus, the interest was shifted to multiphase high-impact polystyrene (HIPS) and rubber-modified SAN (ABS). In principle, both HIPS and ABS can be manufactured by either bulk or emulsion techniques. However, in actual practice, HIPS is made only by the bulk process, whereas ABS is produced by both methods [132,133]. 

The molecules join together to form a long chain-like molecule which may contain many thousands of ethylene units. Such a molecule is referred to as a polymer, in this case polyethylene, whilst in this context ethylene is referred to as a monomer. Styrene, propylene, vinyl chloride, vinyl acetate and methyl methacrylate are other examples of monomers which can polymerise in this way. Sometimes two monomers may be reacted together so that residues of both are to be found in the same chain. Such materials are known as copolymers and are exemplified by ethylene-vinyl acetate copolymers and styrene-acrylonitrile copolymers. 

The authors of [317] investigated compositions based on PS, PMMA and styrene-acrylonitrile copolymer grafted to various fillers and found that it was possible, in this manner, to obtain particles with a grafted polymeric coating of sufficiently homogeneous thickness. 

The electrophilic functions most commonly used in grafting onto processes are ester 141 144), benzylic halide 145,146) and oxirane, 47). Other functions such as nitrile or anhydride could be used as well. The backbone is a homopolymer (such as PMMA) or a copolymer containing both functionalized and unfunctionalized units. Such species can be obtained either by free radical copolymerization (e.g. styrene-acrylonitrile copolymer) or by partial chemical modification of a homopolymer (e.g. 

Determine the copolymer composition for a styrene-acrylonitrile copolymer made at the azeotrope (62 mol% styrene). Assume = 1000. One approach is to use the Gaussian approximation to the binomial distribution. Another is to synthesize 100,000 or so molecules using a random number generator and to sort them by composition. 

Suppose the reactor sized in Problem 13.14 is converted to manufacture a styrene-acrylonitrile copolymer containing 36% acrylonitrile by weight. Assume 50% conversion as before. What is the required feed composition to the reactor and what is the composition of the unreacted monomer mixture ... 

---