Polybutadiene latex

Polymer Components Firestone FR-S-2004 59.2% polybutadiene latex (polybutadiene equivalent) styrene acrylonitrile methyl methacrylate Dispersion Medium deionized distilled water (total)... 

Non-discoloring, sulfur containing phenolic antioxidant and stabilizer that provides long-term heat stability by preventing thermo-oxidative degradation. Used for the process stabilization of polyethylene wire and cable resins for polyethylene during extruder compounding. Can also be applied in styrenic polymers, polypropylene, elastomers such as EPDM and SBR and for carboxylated SBR latex, polybutadiene rubber and polyisopropene rubber. 

Synonyms Atactic butadiene polymer BR Buta-1,3-diene Butadiene homopoiymer 1,3-Butadiene, homopolymer Butadiene oligomer Butadiene poiymer 1,3-Butadiene, poiymers Butadiene resin Butadiene rubber Poiy-1,3-butadiene cis-Poiybutadiene Polybutadiene latex Polybutadiene resin Polybutadiene rubber ClassiTication Polymer elastomer latex Empirical (C4H6) ... 

BNX 1035 is a particularly effective 2Uitioxidant for polyethylene, styrenic polymers, polypropylene and elastomers such as EPDM euid SBR auid for carboxylated SBR latex, polybutadiene rubber and polyisoprene rubber. 

The mbber latex is usually produced in batch reactors. The mbber can be polybutadiene [9003-17-2] or a copolymer of 1,3-butadiene [106-99-0] and either acrylonitrile [107-13-1] or styrene [100-42-5]. The latex normally has a polymer content of approximately 30 to 50% most of the remainder is water. 

M ass Process. In the mass (or bulk) (83) ABS process the polymerization is conducted in a monomer medium rather than in water. This process usually consists of a series of two or more continuous reactors. The mbber used in this process is most commonly a solution-polymerized linear polybutadiene (or copolymer containing sytrene), although some mass processes utilize emulsion-polymerized ABS with a high mbber content for the mbber component (84). If a linear mbber is used, a solution of the mbber in the monomers is prepared for feeding to the reactor system. If emulsion ABS is used as the source of mbber, a dispersion of the ABS in the monomers is usually prepared after the water has been removed from the ABS latex. 

Acrylonitrile—Butadiene—Styrene. ABS is an important commercial polymer, with numerous apphcations. In the late 1950s, ABS was produced by emulsion grafting of styrene-acrylonitrile copolymers onto polybutadiene latex particles. This method continues to be the basis for a considerable volume of ABS manufacture. More recently, ABS has also been produced by continuous mass and mass-suspension processes (237). The various products may be mechanically blended for optimizing properties and cost. Brittle SAN, toughened by SAN-grafted ethylene—propylene and acrylate mbbets, is used in outdoor apphcations. Flame retardancy of ABS is improved by chlorinated PE and other flame-retarding additives (237). 

Polymerization Reactions. The polymerization of butadiene with itself and with other monomers represents its largest commercial use. The commercially most important polymers are styrene—butadiene mbber (SBR), polybutadiene (BR), styrene—butadiene latex (SBL), acrylonittile—butadiene—styrene polymer (ABS), and nittile mbber (NR). The reaction mechanisms are free-radical, anionic, cationic, or coordinate, depending on the nature of the initiators or catalysts (194—196). 

To produce the Type 2 polymers, styrene and acrylonitrile are added to polybutadiene latex and the mixture warmed to about 50°C to allow absorption of the monomers. A water-soluble initiator such as potassium persulphate is then added to polymerise the styrene and acrylonitrile. The resultant materials will be a mixture of polybutadiene, polybutadiene grafted with acrylonitrile and styrene, and styrene-acrylonitrile copolymer. The presence of graft polymer is essential since straightforwsird mixtures of polybutadiene and styrene-acrylonitrile copolymers are weak. In addition to emulsion processes such as those described above, mass and mass/suspension processes are also of importance. 

By this method, the ABS copolymers are obtained by polymerising acrylonitrile and styrene in the presence of polybutadiene latex at 50°C in the presence of initiator and transfer agent. 

Uses Synthetic rubbers and elastomers (styrene-butadiene, polybutadiene, neoprene) organic synthesis (Diels-Alder reactions) latex paints resins chemical intermediate. 

In solution, block copolymers display interesting colloidal and interfacial properties. They can be used as emulsifying agents in water-oil and oil-oil systems (6 ). In the later case, the oil phases are solid and they give rise to polymeric alloys (7.) or they are liquid and they allow the preparation of latexes in organic medium (8 ). However, the molecular structure of block copolymers based on polybutadiene PB (70 ) and polystyrene PS behave as thermoplastic elastomers when engaged in multiblock (PB-PS)n or triblock (PS-PB-PS) structures but never when implied in inverse triblock or diblock arrangements. Similarly the... 

Butadiene is used primarily in the production of synthetic rubbers, including styrene-butadiene rubber (SBR), polybutadiene nibber (BR), styrene-butadiene latex (SBL), chloroprene rubber (CR) and nitrile rubber (NR). Important plastics containing butadiene as a monomeric component are shock-resistant polystyrene, a two-phase system consisting of polystyrene and polybutadiene ABS polymers consisting of acrylonitrile, butadiene and styrene and a copolymer of methyl methacrylate, butadiene and styrene (MBS), which is used as a modifier for poly(vinyl chloride). It is also used as an intermediate in the production of chloroprene, adiponitrile and other basic petrochemicals. The worldwide use pattern for butadiene in 1981 was as follows (%) SBR + SBL, 56 BR, 22 CR, 6 NR, 4 ABS, 4 hexamethylenediamine, 4 other, 4. The use pattern for butadiene in the United States in 1995 was (%) SBR, 31 BR, 24 SBL, 13 CR, 4 ABS, 5 NR, 2 adiponitrile, 12 and other, 9 (Anon., 1996b). 

Butadiene is a monomer used in high volume in the manufacture of a wide range of polymers, including styrene-butadiene rubber, polybutadiene, nitrile rubber, acrylonitrile-butadiene-styrene resins and st rene-butadiene latexes. It is also an intermediate in the production of various other chemicals. 

HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HNS NTO NTO/HMX NTO/HMX NTO/HMX PETN PETN PETN PETN PETN PETN PETN PETN PETN PETN RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX TATB/HMX Cariflex (thermoplastic elastomer) Hydroxy-terminated polybutadiene (polyurethane) Hydroxy-terminated polyester Kraton (block copolymer of styrene and ethylene-butylene) Nylon (polyamide) Polyester resin-styrene Polyethylene Polyurethane Poly(vinyl) alcohol Poly(vinyl) butyral resin Teflon (polytetrafluoroethylene) Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Cariflex (block copolymer of butadiene-styrene) Cariflex (block copolymer of butadiene-styrene) Estane (polyester polyurethane copolymer) Hytemp (thermoplastic elastomer) Butyl rubber with acetyl tributylcitrate Epoxy resin-diethylenetriamine Kraton (block copolymer of styrene and ethylene-butylene) Latex with bis-(2-ethylhexyl adipate) Nylon (polyamide) Polyester and styrene copolymer Poly(ethyl acrylate) with dibutyl phthalate Silicone rubber Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Epoxy ether Exon (polychlorotrifluoroethylene/vinylidine chloride) Hydroxy-terminated polybutadiene (polyurethane) Kel-F (polychlorotrifluoroethylene) Nylon (polyamide) Nylon and aluminium Nitro-fluoroalkyl epoxides Polyacrylate and paraffin Polyamide resin Polyisobutylene/Teflon (polytetrafluoroethylene) Polyester Polystyrene Teflon (polytetrafluoroethylene) Kraton (block copolymer of styrene and ethylene-butylene)... 

RESINS (Acrylonitrile-Butadiene-Styrene). Commonly referred to as ABS resins, these materials are thermoplastic resins which are produced by grafting styrene and acrylonitrile onto a diene-rubber backbone. The usually preferred substrate is polybutadiene because of its low glass-transition temperature (approximately —80°C). Where ABS resin is prepared by suspension or mass polymerization methods, stereospedfic diene rubber made by solution polymerization is the preferred diene. Otherwise, the diene used is a high-gel or cross-linked latex made by a hot emulsion process. 

Most ABS is made by emulsion polymerization. A polybutadiene or nitrile rubber latex is prepared, and styrene plus acrylonitrile are grafted upon the elastomer in emulsion. The effect of rubber particle size in ABS graft copolymer on physical properties is the subject Chapter 22 by C. F. Parsons and E. L. Suck. Methyl methacrylate was substituted for acrylonitrile in ABS by R. D. Deanin and co-workers. They found a better thermoprocessability, lighter color, and better ultraviolet light stability. 

Commercial ABS is prepared primarily by free-radical emulsion copolymerization of styrene and acrylonitrile in the presence of polybutadiene latex (3). This method was therefore adapted for the preparation of ABS and MBS terpolymers and an intermediate AMBS tetrapolymer under similar conditions (Table I). Polymerizations were charged into 12-ounce crown-cap bottles, sparged and flushed with nitrogen, and... 

The formation of coagulum is observed in all types of emulsion polymers (i) synthetic rubber latexes such as butadiene-styrene, acrylonitrile-butadiene, and butadiene-styrene-vinyl pyridine copolymers as well as polybutadiene, polychloroprene, and polyisoprene (ii) coatings latexes such as styrene-butadiene, acrylate ester, vinyl acetate, vinyl chloride, and ethylene copolymers (iii) plastisol resins such as polyvinyl chloride (iv) specialty latexes such as polyethylene, polytetrafluoroethylene, and other fluorinated polymers (v) inverse latexes of polyacrylamide and other water-soluble polymers prepared by inverse emulsion polymerization. There are no major latex classes produced by emulsion polymerization that are completely free of coagulum formation during or after polymerization. 

Recently, a novel method for determining the microstructure of crosslinked polybutadiene in latex using solution 13C-NMR technique was reported [133]. The surfactant and polymer concentrations in the latex were adjusted to give a good signal resolution of the latex sample, as indicated by half-width of the resonance peak at 32.7 ppm. Under these conditions, the S/N ratio was almost identical to that of sample in solution, as shown in Figure 11.31. The microstructure of sol and gel fractions in a radical initiated polybutadiene, determined by this technique, was similar to that of solution measurements. 

Figure 11.31 13C-NMR spectra of polybutadiene containing 80% gel (a) Solution measurement (10 w/v% CDC13 solution), (b) latex measurement (10 w/v % dry rubber content), and (c) solid state measurement [133]...

Figure 2. Particle size distribution of a commercially available polybutadiene latex calculated using different detector response functions.

Since compounds of the type XVII have shown comparable activity in a number of systems including cis-polybutadiene, styrene-butadiene rubber, and ethylene-propylene rubber, they have some commercial promise, and development work on these compounds is continuing. Nevertheless, they are not completely nondiscoloring, and in certain applications, particularly carboxylated styrene-butadiene latex films, yellow discoloration caused by the antioxidant is a serious drawback. We therefore turned our attention to ortho-linked compounds derived from 2,4-dialkylphenols. 

Graft Polymers. The procedure used was described by Cummings (3). To a quantity of commercially available polybutadiene latex (52.3% solids) containing 50 parts of rubber was added sufficient deionized water to increase the water content to 180 parts. The diluted latex was heated to 60°C. Potassium persulfate (0.3 part) and monomers (styrene, acrylonitrile, DBPF 50 parts) were added, and poly-... 

Grafted Rubber Latex Particles as the Disperse Phase. ABS polymers or acrylonitrile-butadiene-styrene polymers, can be generally made by piggy-back grafting of a polybutadiene latex with styrene and... 

---