Ongoing inspection and

Assume that the furnace has or will have cracks, and leaky seals around doors, peep sights, sensors, and car hearth or conveyor. Establish an ongoing inspection and repair program to minimize these possible sources of inleakage or outleakage. 

Safety representatives also assist in maintaining the momentum of the safety program as a result of their ongoing inspections, and liaison with employees. 

Identify those items requiring ongoing inspection and maintenance... 

Another reason for incoming inspection is to identify where there is a need for ongoing inspection and maintenance. Items concerned included inter alia ... 

Ongoing inspection and maintenance inert gas purge/ shaft rotation/heating/dessicant bags/insulation resistance/other ... 

Are materiel incoming inspection, ongoing inspection and maintenance being carried out and recorded to an approved procedure ... 

Discussion It is important that the apparatus assigned to the companies and personnel of this department be available to answer any and all alarms to ensure the safety of this community. Over the past few months, there have been reports that minor problems with apparatus have not been addressed in a timely manner. This is a concern due to the high number of reports of accidents and incidents involving fire service vehicles in the United States. This order will establish a method to ensure that there is a program to inspect and report the findings to the Mechanic s Office before a minor problem becomes the cause of a failure. The Mechanic s Office has an ongoing program... 

Operational checks are normally presenting process control computer systems. These systems may contain code that is part of the master production record. At the system level, the purpose of operational checks is to execute algorithms, sequencing of operations, and safety-related functions as required in the applicable customer specification. Inspections and testing are fundamental processes to be performed during the validation of critical system sequences. In addition, an ongoing program must be established to frequently verify that critical operations occur in the proper sequence. 

Only a qualified company of independent experts can give recognition of the Quality System to ISO standards (Quality Audit). The system is subject to ongoing surveillance and assessment of its compliance with the standards. Regular inspection by trained internal auditors is also carried out to assess the company s continued ability to provide products and services of a suitable quality for the customer by asking the following questions ... 

Sewer pipelines are operated without an ongoing regime of inspection and testing. 

Overall the proeess has identified a number of areas where further action is necessary (alarm reviews) to ensure clarity and integrity of operations to reduce still further the risk of a major accident. There are also a number of metrics that have not worked as well as expected (overdue inspections and operating routine execution) and will require further work to identify better measures. The process as defined in HSG 254 recognizes that this is an ongoing process and indicators that show little change should be reviewed and others tracked instead. 

The manufacturer must carry out on-going real-time stability studies to substantiate the expiry date and the storage conditions previously projected. The data needed to confirm a tentative shelf-life must be submitted to the registration body. Other results of ongoing stability studies are verified in the course of GMP inspections. To ensure the quality and safety of products with particular reference to degradation, national health authorities should monitor the stability and quality of preparations on the market by means of a follow-up inspection and testing programme. 

Engineer hazard control into the design of machines, equipment, and facilities Inspect and maintain machines, equipment, tools, and facilities Incorporate risk control into training, techniques, and methods Comply with safety and health standards Comply with safety and health legislation Identify and eliminate risks on an ongoing basis... 

Periodic non-destructive examination of the piping and components in reactor pressure circuits, as well as of their supports, should be required to detect flaws in the material that may have become enlarged during operation. The sensitivity of the inspection techniques that are used should be set to detect and characterize flaws substantially smaller than those that could cause severe failure. Care should be exercised to ensure that ongoing inspections do not increase P by the thinning of pipework (or by other means). 

During the operations phase, the analysis and control of hazards identified during traditional inspections and worksite monitoring are ongoing. 

In conjunction with adequate record-keeping, inspection facilitates the identification and rectification of problems which may occur over the lifetime service of a component or group of components. This is especially the case where such problems may arise out of design or specification inadequacy - the existence of the inspection and test documentation has ongoing potential value, rated as essential where the consequences of failure are severe. 

Quality Control There should be ongoing quality control procedures. Quality control should address procedures in place and checks to assure that parts, assemblies, and the final product meet specifications and standards. Procedures may include a range of tests, inspection, and analysis. Should quality control uncover defective processes or products, there should be analysis to discover the source of deficiencies. 

Develop an ongoing measurement and feedback system. Drive the system with upstream activity measures that encourage positive change. Examples include the number of hazards reported or corrected, numbers of inspections, number of equipment checks, JHAs, or pre-startup reviews conducted [7]. 

Maintenance programs that include appropriate inspection and testing should be established and implemented for critical equipment to sustain ongoing mechanical integrity. Maintenance activities focused on this equipment should be structured to enhance safety and protect the environment. 

Although debates over the issue of CW inspections and disarmament continue to this day, 1992 marked the starting date of a truly historic ongoing agreement. Having learned the hard way from the deficiencies of the Geneva Protocol of 1925, the CWC was written more forcefully, and refined almost endlessly, in the hopes that chemical weapons would be banned, and banned in a comprehensive and permanent fashion. 

In this Final Rule, U.S. HUD sets forth seven strategies for lead paint or paint hazard evaluation and hazard reduction, varying in relative stringency from least to most (1) safe work practices during rehabilitation (2) ongoing lead paint maintenance practices to assure continued intact surfaces (3) visual assessment and paint stabihzation (4) risk assessment and interim controls (as defined above) (5) combined risk assessment and lead paint inspection with interim controls (6) risk assessment and abatement of lead paint hazards and (7) lead-based paint inspection and abatement via removal of aU lead paint. 

---