Further Work

The above discussion has highlighted several areas which require further work to quantify the risk of criticality occurring. Areas to be studied should include  

Here we have discussed only very few of the many ligands that have been made. Many variations of substituents at the cyclopentadienyl ligand have been studied, and there are more to come, as well as variation in the structure of the bridge, the anions, the central metal, and replacement of the cyclopentadienyl ligand by other bulky ligands. In summary, the toolbox is quite extensive prediction of properties of new polymers to be made could guide the catalysis research in the design of new catalysts. 

---

In the definition phase options are narrowed down and a preferred solution is proposed. The project becomes better defined in terms of what should be built and how it should be operated, and an assessment of how the project may be affected by changes beyond the control of the company (for example the oil price) should be made. Normally a clear statement should be prepared, describing why the option is preferred and what project specifications must be met, to be used as a basis for further work. 

Again, no further explanation of this reaction scheme is intended here. It should just illustrate the complexity of the problem and present a challenge for further work. 

In order to save the cost of the distilling-flask (which after the above treatment is useless for further work), the mixture may be distilled from a small retort made by blowing a suitable bulb on the end of a rather thick-walled tube of about 8-10 mm. internal diameter the tube is then bent through almost 90° a few cm. above the bulb, cut to a suitable length, and the Open end fitted into the boiling ube as before. 

Nitration using this reagent was first investigated, by Francis. He showed that benzene and some of its homologues bromobenzene, benzonitrile, benzoyl chloride, benzaldehyde and some related compounds, and phenol were mono-nitrated in solutions of benzoyl nitrate in carbon tetrachloride anilines would not react cleanly and a series of naphthols yielded dinitro compounds. Further work on the orientation of substitution associated this reagent with higher proportions of o-substitution than that brought about by nitric acid this point is discussed below ( 5.3.4). 

The evidence in favour of the tensile strength hypothesis accumulated so far is encouraging, but further work is needed before it can be regarded as fully substantiated. In particular, the existence of a minimum value of relative... 

Figure 8.3b shows that phase separation in polymer mixtures results in two solution phases which are both dilute with respect to solute. Even the relatively more concentrated phase is only 10-20% by volume in polymer, while the more dilute phase is nearly pure solvent. The important thing to remember from both the theoretical and experimental curves of Fig. 8.3 is that both of the phases which separate contain some polymer. If it is the polymer-rich or precipitated phase that is subjected to further work-up, the method is called fractional precipitation. If the polymer-poor phase is the focus of attention, the method... 

Further work is needed to build a physical model that allows prediction of the concentration effect from the primary properties of the slurry or from a limited amount of slurry testing. 

In addition to the processes mentioned above, there are also ongoing efforts to synthesize formamide direcdy from carbon dioxide [124-38-9J, hydrogen [1333-74-0] and ammonia [7664-41-7] (29—32). Catalysts that have been proposed are Group VIII transition-metal coordination compounds. Under moderate reaction conditions, ie, 100—180°C, 1—10 MPa (10—100 bar), turnovers of up to 1000 mole formamide per mole catalyst have been achieved. However, since expensive noble metal catalysts are needed, further work is required prior to the technical realization of an industrial process for formamide synthesis based on carbon dioxide. 

Consolidation. Metal powders are consoHdated by heat or by pressure followed by heat, or by heating during the appHcation of pressure (17). ConsoHdation produces a coherent mass of definitive size and shape for further working, heat treating, or use as is. 

Pubhc concerns about pesticides in the diet of infants and children resulted in an expert committee convened by the U.S. National Academy of Sciences which devoted four years to the review of all available data. A consensus report was issued in 1993 (80). A number of recommendations for further work to more precisely define what constitutes the diet of infants and children were made. No risk could be estimated. The residue data reviewed by the panel were mainly from monitoring studies conducted by the PDA using multiresidue methods to analyze fresh produce and market basket samples collected from various geographic areas (81,82). These and other rehable scientific studies have demonstrated that relatively few food samples contain detectable residues. Most residues are far below estabhshed tolerances which are set above the maximum residue found in treated raw agricultural... 

Quaternary ammonium alkyl ethers are prepared similarly an alkaline starch is reacted with a quaternary ammonium salt containing a 3-chloto-2-hydtoxyptopyl or 2,3-epoxyptopyl radical. Alternatively, such derivatives can be prepared by simple quaternization of tertiary aminoalkyl ethers by reaction with methyl iodide. Sulfonium (107) and phosphonium (108) starch salts have also been prepared and investigated. Further work has explained the synthesis of diethyl aminoethyl starch (109) as well as the production of cationic starches from the reaction of alkaline starch with... 

The austenitic iron—chromium—nickel alloys were developed in Germany around 1910 in a search for materials for use in pyrometer tubes. Further work led to the widely used versatile 18% chromium—8% nickel steels, the socaHed 18—8. 

Further work elucidated the stmcture of the dyes in this group by synthesizing trichioroarylthiazinones (18) from an o-aminoaryl mercaptan (19) and chloranil (20) treatment with sodium disulfide replaced the halogens by mercapto groups. 

The radiological hazard of tritium to operating personnel and the general population is controlled by limiting the rates of exposure and release of material. Maximum permissible concentrations (MPC) of radionucHdes were specified in 1959 by the International Commission on Radiological Protection (79). For purposes of control all tritium is assumed to be tritiated water, the most readily assimilated form. The MPC of tritium ia breathing air (continuous exposure for 40 h/wk) is specified as 185 kBq/mL (5 p.Ci/mL) and the MPC for tritium in drinking water is set at 3.7 GBq/mL (0.1 Ci/mL) (79). The maximum permitted body burden is 37 MBq (one millicurie). Whenever bioassay indicates this value has been exceeded, the individual is withdrawn from further work with tritium until the level of tritium is reduced. 

The polymerisation in sealed tubes of vinyl chloride and vinyl bromide, when exposed to sunlight, was reported in 1872 by Baumann. Further work on these polymerisations was carried out by Ostromislensky in Moscow and this was duly reported in 1912. ... 

The cycle life of the hydrogen-containing samples also appears to be limited as shown in ref 8. This is unacceptable for a practical application. The capacity loss is mostly due to the elimination of the excess capacity which exhibits hysteresis. Since this portion of the capacity appears related to the incorporated hydrogen, its elimination with cycling may not be unexpected. We do not understand this point fully yet, and further work would appear to be warranted. 

An analogous mechanism should also produce polymers on irradiation of epoxies. Crivello s recent mechanistic suggestions [29] are consistent with the mechanisms given above. One can conclude that radiation-induced polymerization of epoxies can proceed via several mechanisms. However, further work is needed to determine the relative contributions of the different mechanisms, which might vary from one epoxy to another. As part of the Interfacial Properties of Electron Beam Cured Composites CRADA [37], an in-depth study of the curing mechanism for the cationic-initiated epoxy polymerization is being undertaken. 

---