Energy released

The energy released in an explosion in a process plant is either chemical or physical ... 

The problem of explosion of a vapor cloud is not only that it is potentially very destructive but also that it may occur some distance from the point of vapor release and may thus threaten a considerable area. If the explosion occurs in an unconfined vapor cloud, the energy in the blast wave is generally only a small fraction of the energy theoretically available from the combustion of all the material that constitutes the cloud. The ratio of the actual energy released to that theoretically available from the heat of combustion is referred to as the explosion efficiency. Explosion efficiencies are typically in the range of 1 to 10 percent. A value of 3 percent is often assumed. 

In fact, the true fire load will be greater than the energy release calculated in Example 9.1. In practice, such a release of superheated liquid generates large amounts of fine spray in addition to the vapor. This can double the energy release based purely on vaporization. 

The mass or volume heating value represents the quantity of energy released by a unit mass or volume of fuel during the chemical reaction for complete combustion producing CO2 and H2O. The fuel is taken to be, unless mentioned otherwise, at the liquid state and at a reference temperature, generally 25°C. The air and the combustion products are considered to be at this same temperature. 

Acoustic emission is a naturally occurring phenomenon within materials, and the term Acoustic Emission is used to define the spontaneous elastic energy released within material or by a process, in the form of transient elastic waves. (2)... 

Elastic energy release due to subcritical crack growth is one recognized source of structure-related AE within its acknowledged lunitations, AEBIL provides a viable means of early on-line deteetion and localization of stable crack propagation. 

Calculate the energy release in kilocalories per mole (kcal/mol) of He for the cold fusion reaction... 

The temi action spectroscopy refers to how a particular action , or process, depends on photon energy. For example, the photodissociation of 0 with UV light leads to energetic 0+0 fragments the kinetic energy released has been... 

Figure A3.5.2. The Ar photofragment energy spectmm for the dissociation of fiions at 752.5 mn. The upper scale gives the kinetic energy release in the centre-of-mass reference frame, both parallel and antiparallel to the ion beam velocity vector in the laboratory.

A very extreme version of surface corrugation has been found in the nonactivated dissociation reactions of Fl2 on W [, ], Pd and Rli systems. In these cases, the very strong chemisorption bond of the FI atoms gives rise to a very large energy release when the molecule dissociates. In consequence, at certain sites on the surface, the molecule accelerates rapidly downliill into the dissociation state. At the unfavourable sites, there... 

A number of different experimental methods may be used to energize the unimolecular reactant A. For example, energization can take place by the potential energy release in chemical reaction, i.e. 

AES Auger electron spectroscopy After the ejection of an electron by absorption of a photon, an atom stays behind as an unstable Ion, which relaxes by filling the hole with an electron from a higher shell. The energy released by this transition Is taken up by another electron, the Auger electron, which leaves the sample with an element-specific kinetic energy. Surface composition, depth profiles... 

With most non-isothemial calorimeters, it is necessary to relate the temperature rise to the quantity of energy released in the process by determining the calorimeter constant, which is the amount of energy required to increase the temperature of the calorimeter by one degree. This value can be detemiined by electrical calibration using a resistance heater or by measurements on well-defined reference materials [1], For example, in bomb calorimetry, the calorimeter constant is often detemiined from the temperature rise that occurs when a known mass of a highly pure standard sample of, for example, benzoic acid is burnt in oxygen. 

The energy released when the process under study takes place makes the calorimeter temperature T(c) change. In an adiabatically jacketed calorimeter, T(s) is also changed so that the difference between T(c) and T(s) remains minimal during the course of the experiment that is, in the best case, no energy exchange occurs between the calorimeter (unit) and the jacket. The themial conductivity of the space between the calorimeter and jacket must be as small as possible, which can be achieved by evacuation or by the addition of a gas of low themial conductivity, such as argon. 

This type of calorimeter is nomrally enclosed in a themiostatted-jacket having a constant temperature T(s). and the calorimeter (vessel) temperature T(c) changes tln-ough the energy released as the process under study proceeds. The themial conductivity of the intemiediate space must be as small as possible. Most combustion calorimeters fall into this group. 

A vital biophysico-chemical problem is to understand how chemical energy (released by ATP or GTP hydrolysis... 

What is the average energy release per bond on breaking bonds in cubane Compare this with the energy released on hydrogenation of ethylene. 

An alternative mechanism of excess energy release when electron relaxation occurs is through x-ray fluorescence. In fact, x-ray fluorescence favorably competes with Auger electron emission for atoms with large atomic numbers. Figure 16 shows a plot of the relative yields of these two processes as a function of atomic number for atoms with initial K level holes. The cross-over point between the two processes generally occurs at an atomic number of 30. Thus, aes has much greater sensitivity to low Z elements than x-ray fluorescence. 

Fracture mechanics (qv) tests are typically used for stmctural adhesives. Thus, tests such as the double cantilever beam test (Fig. 2c), in which two thick adherends joined by an adhesive are broken by cleavage, provide information relating to stmctural flaws. Results can be reported in a number of ways. The most typical uses a quantity known as the strain energy release rate, given in energy per unit area. 

Exothermic oxidation—reduction reactions provide the energy released in both propellant burning and explosive detonation. The reactions are either internal oxidation—reductions, as in the decomposition of nitroglycerin and pentaerythritol tetranitrate, or reactions between discrete oxidizers and fuels in heterogeneous mixtures. 

Steric Factors. Initially, most of the coUisions of fluorine molecules with saturated or aromatic hydrocarbons occur at a hydrogen site or at a TT-bond (unsaturated) site. When coUision occurs at the TT-bond, the double bond disappears but the single bond remains because the energy released in initiation (eq. 4) is insufficient to fracture the carbon—carbon single bond. Once carbon—fluorine bonds have begun to form on the carbon skeleton of either an unsaturated or alkane system, the carbon skeleton is somewhat stericaUy protected by the sheath of fluorine atoms. Figure 2, which shows the crowded hehcal arrangement of fluorine around the carbon backbone of polytetrafluoroethylene (PTFE), is an example of an extreme case of steric protection of carbon—carbon bonds (29). 

Because G is defined as the energy released per unit area of crack surface formed, or more correctiy the energy which would be released if the crack were to grow at the present appHed load, then ... 

---