Coproduct development

Since 1960, the Hquid-phase oxidation of ethylene has been the process of choice for the manufacture of acetaldehyde. There is, however, stiU some commercial production by the partial oxidation of ethyl alcohol and hydration of acetylene. The economics of the various processes are strongly dependent on the prices of the feedstocks. Acetaldehyde is also formed as a coproduct in the high temperature oxidation of butane. A more recently developed rhodium catalyzed process produces acetaldehyde from synthesis gas as a coproduct with ethyl alcohol and acetic acid (83—94). 

ARCO has developed a coproduct process which produces KA along with propylene oxide [75-56-9] (95—97). Cyclohexane is oxidized as in the high peroxide process to maximize the quantity of CHHP. The reactor effluent then is concentrated to about 20% CHHP by distilling off unreacted cyclohexane and cosolvent tert-huty alcohol [75-65-0]. This concentrate then is contacted with propylene [115-07-1] in another reactor in which the propylene is epoxidized with CHHP to form propylene oxide and KA. A molybdenum catalyst is employed. The product ratio is about 2.5 kg of KA pet kilogram of propylene oxide. 

Early demand for chlorine centered on textile bleaching, and chlorine generated through the electrolytic decomposition of salt (NaCl) sufficed. Sodium hydroxide was produced by the lime—soda reaction, using sodium carbonate readily available from the Solvay process. Increased demand for chlorine for PVC manufacture led to the production of chlorine and sodium hydroxide as coproducts. Solution mining of salt and the avadabiHty of asbestos resulted in the dominance of the diaphragm process in North America, whereas soHd salt and mercury avadabiHty led to the dominance of the mercury process in Europe. Japan imported its salt in soHd form and, until the development of the membrane process, also favored the mercury ceU for production. 

Manufacture of Fatty Acids and Derivatives. Splitting of fats to produce fatty acids and glycerol (a valuable coproduct) has been practiced since before the 1890s. In early processes, concentrated alkaU reacted with fats to produce soaps followed by acidulation to produce the fatty acids. Acid-catalyzed hydrolysis, mostly with sulfuric and sulfonic acids, was also practiced. Pressurized equipment was introduced to accelerate the rate of the process, and finally continuous processes were developed to maximize completeness of the reaction (105). Lipolytic enzymes maybe utilized to spHt... 

Sasol produces synthetic fuels and chemicals from coal-derived synthesis gas. Two significant variations of this technology have been commercialized, and new process variations are continually under development. Sasol One used both the fixed-bed (Arge) process, operated at about 240°C, as weU as a circulating fluidized-bed (Synthol) system operating at 340°C. Each ET reactor type has a characteristic product distribution that includes coproducts isolated for use in the chemical industry. Paraffin wax is one of the principal coproducts of the low temperature Arge process. Alcohols, ketones, and lower paraffins are among the valuable coproducts obtained from the Synthol process. 

Direct Fluorination. This is a more recently developed method for the synthesis of perfluorinated compounds. In this process, fluorine gas is passed through a solution or suspension of the reactant in a nonreactive solvent such as trichlorotrifluoroethane (CFC-113). Sodium fluoride may also be present in the reaction medium to remove the coproduct hydrogen fluoride. There has been enormous interest in this area since the early 1980s resulting in numerous journal pubHcations and patents (7—9) (see Fluorine compounds, organic-direct fluorination). Direct fluorination is especially useful for the preparation of perfluoroethers. 

Liquid-phase oxidation of lower hydrocarbons has for many years been an important route to acetic acid [64-19-7]. In the United States, butane has been the preferred feedstock, whereas ia Europe naphtha has been used. Formic acid is a coproduct of such processes. Between 0.05 and 0.25 tons of formic acid are produced for every ton of acetic acid. The reaction product is a highly complex mixture, and a number of distillation steps are required to isolate the products and to recycle the iatermediates. The purification of the formic acid requires the use of a2eotropiag agents (24). Siace the early 1980s hydrocarbon oxidation routes to acetic acid have decliaed somewhat ia importance owiag to the development of the rhodium-cataly2ed route from CO and methanol (see Acetic acid). 

The unit Kureha operated at Nakoso to process 120,000 metric tons per year of naphtha produces a mix of acetylene and ethylene at a 1 1 ratio. Kureha s development work was directed toward producing ethylene from cmde oil. Their work showed that at extreme operating conditions, 2000°C and short residence time, appreciable acetylene production was possible. In the process, cmde oil or naphtha is sprayed with superheated steam into the specially designed reactor. The steam is superheated to 2000°C in refractory lined, pebble bed regenerative-type heaters. A pair of the heaters are used with countercurrent flows of combustion gas and steam to alternately heat the refractory and produce the superheated steam. In addition to the acetylene and ethylene products, the process produces a variety of by-products including pitch, tars, and oils rich in naphthalene. One of the important attributes of this type of reactor is its abiUty to produce variable quantities of ethylene as a coproduct by dropping the reaction temperature (20—22). 

Acetylene Recovery Process. A process to recover coproduct acetylene developed by Linde AG (Fig. 11), and reduced to practice in 11 commercial plants, comprises three sections acetylene absorption, ethylene stripper, and acetylene stripper. 

The yield of hydroquinone is 85 to 90% based on aniline. The process is mainly a batch process where significant amounts of soHds must be handled (manganese dioxide as well as metal iron finely divided). However, the principal drawback of this process resides in the massive coproduction of mineral products such as manganese sulfate, ammonium sulfate, or iron oxides which are environmentally not friendly. Even though purified manganese sulfate is used in the agricultural field, few solutions have been developed to dispose of this unsuitable coproduct. Such methods include MnSO reoxidation to MnO (1), or MnSO electrochemical reduction to metal manganese (2). None of these methods has found appHcations on an industrial scale. In addition, since 1980, few innovative studies have been pubUshed on this process (3). 

The handling of toxic materials and disposal of ammonium bisulfate have led to the development of alternative methods to produce this acid and the methyl ester. There are two technologies for production from isobutylene now available ammoxidation to methyl methacrylate (the Sohio process), which is then solvolyzed, similar to acetone cyanohydrin, to methyl methacrylate and direct oxidation of isobutylene in two stages via methacrolein [78-85-3] to methacryhc acid, which is then esterified (125). Since direct oxidation avoids the need for HCN and NH, and thus toxic wastes, all new plants have elected to use this technology. Two plants, Oxirane and Rohm and Haas (126), came on-stream in the early 1980s. The Oxirane plant uses the coproduct tert-huty alcohol direcdy rather than dehydrating it first to isobutylene (see Methacrylic acid). 

A second route based on olefin disproportionation was developed by Phillips Petroleum (131). Here isobutylene reacts with propylene to form isoamylenes, which are dehydrogenated to isoprene. 2-Butene can be used in place of propylene since it also yields isoamylene and the coproduct propylene can be recycled. Use of mixed butylenes causes the formation of pentenes, giving piperjlene, which contaminates isoprene. 

Dutch State Mines (Stamicarbon). Vapor-phase, catalytic hydrogenation of phenol to cyclohexanone over palladium on alumina, Hcensed by Stamicarbon, the engineering subsidiary of DSM, gives a 95% yield at high conversion plus an additional 3% by dehydrogenation of coproduct cyclohexanol over a copper catalyst. Cyclohexane oxidation, an alternative route to cyclohexanone, is used in the United States and in Asia by DSM. A cyclohexane vapor-cloud explosion occurred in 1975 at a co-owned DSM plant in Flixborough, UK (12) the plant was rebuilt but later closed. In addition to the conventional Raschig process for hydroxylamine, DSM has developed a hydroxylamine phosphate—oxime (HPO) process for cyclohexanone oxime no by-product ammonium sulfate is produced. Catalytic ammonia oxidation is followed by absorption of NO in a buffered aqueous phosphoric acid... 

Coal Char This type of char is the nonagglomerated, nonfusible residue from the thermal treatment of coal. Coal chars are obtained as a residue or a coproduct from low-temperature carbonization processes and from processes being developed to convert coal to hquid and gaseous fuels and to chemicals. Such chars have a substantial heating value. The net amount of char from a conversion process varies widely in some instances, it may represent between about 30... 

Coproduction of electricity along with synthesis gas conversion offers the potential for significant cost savings. The once-through liquid-phase methanol technology was developed specifically for this... 

Beyond the ATS program, the DOE is looking at several new initiatives to work on -with industry. One, Vision 21, aims to virtually eliminate environmental concerns associated with coal and fossil systems while achieving 60 percent efficiency for coal-based plants, 75 percent efficiency for gas-based plants, and 85 percent for coproduction facilities. Two additional fossil cycles have been proposed that can achieve 60 percent efficiency. One incorporates a gasifier and solid oxide fuel into a combined cycle the other adds a pyrolyzer with a pressurized fluidized bed combustor. Also under consideration is the development of a flexible midsize gas turbine. This initiative would reduce the gap between the utility-size turbines and industrial turbines that occurred during the DOE ATS program. 

Chemicals directly based on propane are few, although as mentioned, propane and LPG are important feedstocks for the production of olefins. Chapter 6 discusses a new process recently developed for the dehydrogenation of propane to propylene for petrochemical use. Propylene has always been obtained as a coproduct with ethylene from steam cracking processes. Chapter 6 also discusses the production of aromatics from LPG through the Cyclar process. ... 

Make Useful Coproducts. The success of this approach to process development is heavily dependent on the market situation but in suitable cases where there is market demand for the total output of both products such processes can be successful. Examples here are the coproduction of phenol and acetone, which is essentially noncatalytic, and the more recently developed process for the cooxidation of ethyl benzene and propylene to produce propylene oxide and styrene. 

Example 12.7 Develop a model for the anaerobic batch fermentation of glucose to ethanol and coproduct CO2 using Saccharomyces cerevisiae. The starting mixture contains 10% glucose. The inoculum is 0.0005 w/w. Product inhibition stops cell growth at 14% ethanol. Assume ka = 0 but include the cannibalization of cellular material beginning when the substrate is completely consumed. 

Anionicallv Activated Alumina. At this time we had also developed an interest in anionically activated alumina. These basic reagents were active in promoting alkylation(42), condensation(43) and hydrolysis(44) reactions. Thus, we impregnated alumina with sodium hydroxide and used this combination both with and without a phase transfer catalyst (benzyltriethyl ammonium chloride). When BTEAC was added, the conversion to ether was decreased and the formation of ester was noted. In the absence of a phase transfer catalyst, the ether became a minor product and methyl phenylacetate became the major product with coproduction of phenylacetic acid. This ester does not result from esterification of the acid as simple stirring of phenylacetic acid with Na0H/A1203 in methanol does not produce methyl phenylacetate. 

The development of versatile and efficient methods for the synthesis of amines has long been an active area of research, mainly because a wide variety of amines play important roles in many fields of organic chemistry. The N-alkylation of amines with alcohols represents an attractive method for synthesizing various amines because it does not generate any wasteful byproducts (H2O is the only stoichiometric coproduct). Although several catalytic systems for this process have been studied using transition-metal catalysts [53-57], most of these require a high reaction temperature (>150°C). 

Solution processes for removal of SO2 from effluent gas streams normally require lower absorption temperatures than do gas phase techniques. Thus, of the four listed in Table IV only the Molten Salt Method has the capability of accepting high temperature flue gas without cooling. In all but one of the cases, elemental sulphur is the end product and in the single instance of the Ammoniacal Solution Process, sulphur is a coproduct with ammonium sulphate. This process has been extensively examined and developed in a number of countries, and is chemically interesting because of the unusual redox reaction that is suspected to take place between the products of air oxidation of SO2 absorbed in ammonia solution. Both products, sulphur and ammonium sulphate, are normally saleable commodities. 

---