Chemical spectrometry

Using Mass Spectrometry for Determining Distribution by Chemical Families... 

The resulting mass spectrometry analysis is an analysis by chemical... 

Separation of families by merely increasing the resolution evidently can not be used when the two chemical families have the same molecular formula. This is particularly true for naphthenes and olefins of the formula, C H2 , which also happen to have very similar fragmentation patterns. Resolution of these two molecular types is one of the problems not yet solved by mass spectrometry, despite the efforts of numerous laboratories motivated by the refiner s major interest in being able to make the distinction. Olefins are in fact abundantly present in the products from conversion processes. 

Analysis of such cuts by spectrometry requires a preliminary separation by chemical constituents. The separation is generally done by liquid phase chromatography described in article 3.3.5. 

Mass spectrometry allows analysis by hydrocarbon family for a variety of petroleum cuts as deep as vacuum distillates since we have seen that the molecules must be vaporized. The study of vacuum residues can be conducted by a method of direct introduction which we will address only briefly because the quantitative aspects are ek r metiy difficult to master. Table 3.6 gives some examples the matrices used differ according to the distillation cut and the chemical content such as the presence or absence of olefins or sulfur. 

Interest in this method has decreased since advances made in gas chromatography using high-resolution capillary columns (see article 3.3.3.) now enable complete identification by individual chemical component with equipment less expensive than mass spectrometry. 

Other techniques for predicting the cetane number rely on chemical analysis (Glavinceski et al., 1984) (Pande et al., 1990). Gas phase chromatography can be used, as can NMR or even mass spectrometry (refer to 3.2.1.l.b and 3.2.2.2). 

Harrison A G 1992 Chemical Ionization Mass Spectrometry (Boca Raton, FL Chemloal Rubber Company)... 

Secondary ion mass spectrometry (SIMS) is by far the most sensitive surface teclmique, but also the most difficult one to quantify. SIMS is very popular in materials research for making concentration depth profiles and chemical maps of the surface. For a more extensive treatment of SIMS the reader is referred to [3] and [14. 15 and 16]. The principle of SIMS is conceptually simple When a surface is exposed to a beam of ions... 

In contrast to IR and NMR spectroscopy, the principle of mass spectrometry (MS) is based on decomposition and reactions of organic molecules on theii way from the ion source to the detector. Consequently, structure-MS correlation is basically a matter of relating reactions to the signals in a mass spectrum. The chemical structure information contained in mass spectra is difficult to extract because of the complicated relationships between MS data and chemical structures. The aim of spectra evaluation can be either the identification of a compound or the interpretation of spectral data in order to elucidate the chemical structure [78-80],... 

Molecular ion (Section 13 22) In mass spectrometry the species formed by loss of an electron from a molecule Molecular orbital theory (Section 2 4) Theory of chemical bonding in which electrons are assumed to occupy orbitals in molecules much as they occupy orbitals in atoms The molecular orbitals are descnbed as combinations of the or bitals of all of the atoms that make up the molecule Molecularity (Section 4 8) The number of species that react to gether in the same elementary step of a reaction mechanism... 

The section on Spectroscopy has been retained but with some revisions and expansion. The section includes ultraviolet-visible spectroscopy, fluorescence, infrared and Raman spectroscopy, and X-ray spectrometry. Detection limits are listed for the elements when using flame emission, flame atomic absorption, electrothermal atomic absorption, argon induction coupled plasma, and flame atomic fluorescence. Nuclear magnetic resonance embraces tables for the nuclear properties of the elements, proton chemical shifts and coupling constants, and similar material for carbon-13, boron-11, nitrogen-15, fluorine-19, silicon-19, and phosphoms-31. 

Following the movement of airborne pollutants requires a natural or artificial tracer (a species specific to the source of the airborne pollutants) that can be experimentally measured at sites distant from the source. Limitations placed on the tracer, therefore, governed the design of the experimental procedure. These limitations included cost, the need to detect small quantities of the tracer, and the absence of the tracer from other natural sources. In addition, aerosols are emitted from high-temperature combustion sources that produce an abundance of very reactive species. The tracer, therefore, had to be both thermally and chemically stable. On the basis of these criteria, rare earth isotopes, such as those of Nd, were selected as tracers. The choice of tracer, in turn, dictated the analytical method (thermal ionization mass spectrometry, or TIMS) for measuring the isotopic abundances of... 

The term nebulizer is used generally as a description for any spraying device, such as the hair spray mentioned above. It is normally applied to any means of forming an aerosol spray in which a volume of liquid is broken into a mist of vapor and small droplets and possibly even solid matter. There is a variety of nebulizer designs for transporting a solution of analyte in droplet form to a plasma torch in ICP/MS and to the inlet/ionization sources used in electrospray and mass spectrometry (ES/MS) and atmospheric-pressure chemical ionization and mass spectrometry (APCI/MS). 

The previous discussion has centered on how to obtain as much molecular mass and chemical structure information as possible from a given sample. However, there are many uses of mass spectrometry where precise isotope ratios are needed and total molecular mass information is unimportant. For accurate measurement of isotope ratio, the sample can be vaporized and then directed into a plasma torch. The sample can be a gas or a solution that is vaporized to form an aerosol, or it can be a solid that is vaporized to an aerosol by laser ablation. Whatever method is used to vaporize the sample, it is then swept into the flame of a plasma torch. Operating at temperatures of about 5000 K and containing large numbers of gas ions and electrons, the plasma completely fragments all substances into ionized atoms within a few milliseconds. The ionized atoms are then passed into a mass analyzer for measurement of their atomic mass and abundance of isotopes. Even intractable substances such as glass, ceramics, rock, and bone can be examined directly by this technique. 

Until 1981, mass spectrometry was limited, generally, to the analysis of volatile, relatively low-molecular-mass samples and was difficult to apply to nonvolatile peptides and proteins without first cutting them chemically into smaller volatile segments. During the past decade, the situation has changed radically with the advent of new ionization techniques and the development of tandem mass spectrometry. Now, the mass spectrometer has a well-deserved place in any laboratory interested in the analysis of peptides and proteins. 

This accurate measurement of the ratio of abundances of isotopes is used for geological dating, estimation of the ages of antiquities, testing athletes for the use of banned steroids, examining fine details of chemical reaction pathways, and so on. These uses are discussed in this book under various headings concerned with isotope ratio mass spectrometry (see Chapters 7, 14, 15, 16, 17, 47, and 48). 

Some of the target molecules gain so much excess internal energy in a short space of time that they lose an electron and become ions. These are the molecular cation-radicals found in mass spectrometry by the direct absorption of radiation. However, these initial ions may react with accompanying neutral molecules, as in chemical ionization, to produce protonated molecules. 

Thus, either the emitted light or the ions formed can be used to examine samples. For example, the mass spectrometric ionization technique of atmospheric-pressure chemical ionization (APCI) utilizes a corona discharge to enhance the number of ions formed. Carbon arc discharges have been used to generate ions of otherwise analytically intractable inorganic substances, with the ions being examined by mass spectrometry. 

The three isotopes of hydrogen are almost indistinguishable for most chemical purposes, but a mass Spectrometer can see them as three different entities of mass 1, 2, and 3 Da. Isotopes of other elements can also be distinguished. Mass spectrometry is important for its ability to separate the isotopes of elements. 

Biemann, K., Mass Spectrometry Organic Chemical Applications, McGraw-Hill, New York, 1962. 

Budde, W.L., Analytical Mass Spectrometry Strategies for Environmental and Related Applications, American Chemical Society, Washington, D.C., 2001. 

Chapman, J.R., Practical Mass Spectrometry A Guide for Chemical and Biochemical Analysis, Wiley, Chichester, U.K., 1995. 

Cotter, R.J., Time-of-Flight Mass Spectrometry, ACS Symposium Series, Vol. 549, American Chemical Society, Washington, DC, 1994. 

Chemical analysis of the metal can serve various purposes. For the determination of the metal-alloy composition, a variety of techniques has been used. In the past, wet-chemical analysis was often employed, but the significant size of the sample needed was a primary drawback. Nondestmctive, energy-dispersive x-ray fluorescence spectrometry is often used when no high precision is needed. However, this technique only allows a surface analysis, and significant surface phenomena such as preferential enrichments and depletions, which often occur in objects having a burial history, can cause serious errors. For more precise quantitative analyses samples have to be removed from below the surface to be analyzed by means of atomic absorption (82), spectrographic techniques (78,83), etc. 

Elemental chemical analysis provides information regarding the formulation and coloring oxides of glazes and glasses. Energy-dispersive x-ray fluorescence spectrometry is very convenient. However, using this technique the analysis for elements of low atomic numbers is quite difficult, even when vacuum or helium paths are used. The electron-beam microprobe has proven to be an extremely useful tool for this purpose (106). Emission spectroscopy and activation analysis have also been appHed successfully in these studies (101). 

---