Acrylate modified epoxy resins

UV-sensitive adhesives are based on acrylate-modified epoxy resins, polyurethane, and amongst others, polymers. They are single-component reactive adhesives, which undergo rapid polymerization upon irradiation with UV light with wavelengths ranging from 400 to 500 nm. These adhesives should be stored in small opaque containers of up to 50 mL in volume. They can be stored in their original containers for 6 months at 10-25°C. [Pg.934]

Studies of the particle—epoxy interface and particle composition have been helpful in understanding the rubber-particle formation in epoxy resins (306). Based on extensive dynamic mechanical studies of epoxy resin cure, a mechanism was proposed for the development of a heterophase morphology in rubber-modified epoxy resins (307). Other functionalized mbbers, such as amine-terminated butadiene—acrylonitrile copolymers (308) and tf-butyl acrylate—acrylic acid copolymers (309), have been used for toughening epoxy resins. [Pg.422]

Another development has been reported by P.A. Lucas, W.E. Stamer and S.G. Musselman of Air Products and Chemicals Inc. (Lucas et al., 1994). An acrylate functional urethane flexibiliser has been used to modify epoxy resin, which optimises reactivity and is more compatible with epoxy. Urethane-acrylate flexibiliser offers very tough hybrid epoxy systems meeting the more demanding requirements of civil engineering applications. [Pg.206]

The electron beam curing of coatings has for some time attracted a great deal of attention since It Is claimed that coatings can be fully cured In a fraction of a — second. The coatings are primarily based on the cross-linking of acrylic or epoxy resins In a polyurethane or polyester base (l.e., modified paints). [Pg.111]

TEM was used to study the toughening mechanism in rubber modified plastics. A crack tip of a damaged sample of an acrylic rubber modified epoxy resin was observed [Sue et al., 1993]. [Pg.554]

For many years, paints used to coat cans contained considerable amounts of volatile organic solvents. Waterborne can coatings were developed to reduce solvent emissions and are used worldwide. Binders used in waterborne can coatings are modified epoxy resins (see Section 2.10). Acidic acrylate chains are grafted onto an epoxy molecule. After partially neutralizing with amines, the resins can be dispersed in water. [Pg.261]

Electrical conductivity measurements have been reported on a wide range of polymers including carbon nanofibre reinforced HOPE [52], carbon black filled LDPE-ethylene methyl acrylate composites [28], carbon black filled HDPE [53], carbon black reinforced PP [27], talc filled PP [54], copper particle modified epoxy resins [55], epoxy and epoxy-haematite nanorod composites [56], polyvinyl pyrrolidone (PVP) and polyvinyl alcohol (PVA) blends [57], polyacrylonitrile based carbon fibre/PC composites [58], PC/MnCli composite films [59], titanocene polyester derivatives of terephthalic acid [60], lithium trifluoromethane sulfonamide doped PS-block-polyethylene oxide (PEO) copolymers [61], boron containing PVA derived ceramic organic semiconductors [62], sodium lanthanum tetrafluoride complexed with PEO [63], PC, acrylonitrile butadiene [64], blends of polyethylene dioxythiophene/ polystyrene sulfonate, PVC and PEO [65], EVA copolymer/carbon fibre conductive composites [66], carbon nanofibre modified thermotropic liquid crystalline polymers [67], PPY [68], PPY/PP/montmorillonite composites [69], carbon fibre reinforced PDMS-PPY composites [29], PANI [70], epoxy resin/PANI dodecylbenzene sulfonic acid blends [71], PANI/PA 6,6 composites [72], carbon fibre EVA composites [66], HDPE carbon fibre nanocomposites [52] and PPS [73]. [Pg.110]

PREPARATION OF IMPACT MODIFIED EPOXY RESIN BY USING POLYBUTYL ACRYLATE/ POLYGLYCIDYL METHACRYLATE CORESHELL COMPOSITE PARTICLES... [Pg.107]

Data from U.S. International Trade Commission, Synthetic Organic Chemicals. Data include modified and unmodified epoxy resins. Modified epoxy resins include solid epoxy resin (SER), vinyl ester resins, epoxy acrylates, etc. There appear to be some discrepancies in epoxy resin production and market data as reported by different publications and organizations (7). This is primarily due to the fact that some epoxy resins such as liquid DGEBA resins and epoxy novolacs are used as raw materials to produce modified or advanced epoxy resins, which may be further converted to end-use products. Some pubhcations report only unmodified epoxies. [Pg.2659]

Elastomer-modified epoxy resins are used in composites and structural adhesives, coatings, and electronic applications. Similar approach to toughen epoxy vinyl esters using other elastomeric materials has been reported (204). Other elastomer-modified epoxies include epoxy-terminated urethane prepolymers, epoxy-terminated polysulfide, epoxy-acrylated urethane, and epoxidized polybutadiene. Preformed dispersions of epoxy-insoluble elastomers have been developed and reported to achieve toughening without Tg reduction (205,206). [Pg.2746]

The acrylic modified epoxy copolymer can be neutralized via the pendant carboxyl groups to provide a water-dispersible system with good hydrolytic stability. The grafting is presumed to occur onto the methylene hydrogens of the glycidyl group in the epoxy resin ... [Pg.306]

Another important class of modified epoxy resins, known as epoxy acrylates, are reaction products of a low MW epoxy resin and acrylic acid or methacrylic acid, which are used in radiation curable systems. The acrylate functionality is 2, but higher functionality variants can also be prepared by using epoxy phenol novolac in place of BPA epoxy resin. Radiation curable formulations from these oligomers provide a better balance of properties and cost compared to some of the alternative polymer systems. [Pg.101]

Oil-base (including oil-modified alkyd resin) paint films should not be used in alkaline environments as the paint will deteriorate owing to saponification alkali-resistant coatings are provided by some cellulose ethers, e.g. ethyl cellulose, certain polyurethane, chlorinated rubber, epoxy, p.v.c./ p.v.a. copolymer, or acrylic-resin-based paints. In particular, aluminium and its alloys should be protected by alkali-resistant coatings owing to the detrimental effects of alkali on these metals. [Pg.612]

S02-cured epoxy resin. Modified epoxy/acrylic resins (1.2 to 1.4% of sand weight) are mixed with organic peroxide (26 to 60% of resin weight), the mixture is blown into the core box and a hardening mechanism similar to the S02 process takes place. [Pg.160]

Structural adhesives are formulated from epoxy resins, phenolic resins, acrylic monomers and resins, high temperature-resistant resins (e.g., polyimidcs), and urethanes. Structural adhesive resins arc often modified by elastomers. [Pg.33]

The higher molecular-weight solid epoxy resins are used in formulations that usually consist of a resin, hardener, reinforcing filler, pigments, flow control agents, and other modifiers. In addition to using conventional hardeners in these formulations, epoxy resins can also be hardened with other resins, ie, acrylics or polyesters. [Pg.370]

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... [Pg.958]

Both aqueous polymer-based systems (latex), made by emulsion or dispersion polymerization, and oil-modified alkyd resin-based systems are still in wide use [781], Table 12.2 shows the composition of a typical water-based emulsion paint. There is a wide variety of coatings, ranging from broad applicability to highly specialized, including latexes, amino resins, isocyanates, epoxy resins, acrylic resins, polyester... [Pg.295]

An acrylate-terminated polyurethane modified epoxy compound and a polyethylene polyamine homologue and fatty acid combination were formulated into a two-component adhesive system. The adhesive is useful for bonding various thermoplastic resins such as ABS, PC, PBT-PC blends, and PPO.22... [Pg.133]