Acid-anionic surfactants

The presence of alkaline earth (Ca2+ and Mg2+) ions during an automatic dishwashing cycle can lead to undesirable spotting and filming on items being washed. This occurs through the formation of insoluble metal complexes with proteinaceous soils, fatty acids, anionic surfactants, and carbonate. Research in... 

The prevalence of the carboxylate moiety in both biogenic and man-made molecules of interest makes this functional group a popular target for anion host chemistry. Needless to say, carboxylates are a major constituent of proteins, peptides and amino acids, and the expansion of proteomics begets increasing requirements for means of specific detection of such biomolecules. Other relevant examples of carboxylates include fatty acids, while many small molecule di- and tricarboxylates are implicated in key metaboUc pathways such as the citric acid cycle (e.g. citrate, succinate, fumarate and malonate). Carboxylated anthropogenic molecules include trichloroacetic acids, anionic surfactants and S-lactam antibiotics. 

Chemical cleaners should be easily removed from treated surfaces without leaving a residue that may influence the odour or flavour of the product that comes into contact with the treated surface. The most common chemical cleaners are chlorine, caustic and quaternary ammonium compounds, and acid-anionic surfactants. 

Inorganic and organic ions Palmitic acid Stearic acid Anionic surfactants I-, SCN-, CIO4... 

Contrarily to fatty add salts (i.e., sodium laurate soap), the long-chain iV -acyl amino adds have excellent water solubility (due to the presence of additional CO-NH linkages), quick biodegradability and good lime resistance (i.e., caldum ion tolerance) [11]. The surfactant properties of pure sodium salts of iV -acyl amino acids (anionic surfactants) with different alkyl chains (saturated and unsaturated with 10-18 carbon atoms) and amino acid residues have been described and compared with those of sodium lauryl sulfate (SLS) and sodium laurate [11-14]. The authors showed that the critical micelle concentration (CMQ of the amino acid-based surfactants was lower than that of the SLS but higher than that of sodium laurate. The surface activity increased and the CMC decreased by raising the alkyl chain... 

Emulsions formed using soap and some other carboxylic acid anionic surfactants are broken by acidification. The surfactant may become water insoluble at low pH and thus can be separated by precipitation or extraction. 

Results can sometimes be unexpected. The first study of this type made use of labeled Aerosol OTN [111], an anionic surfactant, also known as di-n-octylsodium sulfosuccinate. The measured F was twice that in Eq. III-93 and it was realized that hydrolysis had occurred, that is, X + H2O = HX + OH , and that it was the undissociated acid HX that was surface-active. Since pH was essentially constant, the activity of HX was just proportional to C. A similar behavior was found for aqueous sodium stearate [112]. 

A selection of important anionic surfactants is displayed in table C2.3.1. Carboxylic acid salts or tire soaps are tire best known anionic surfactants. These materials were originally derived from animal fats by saponification. The ionized carboxyl group provides tire anionic charge. Examples witlr hydrocarbon chains of fewer tlran ten carbon atoms are too soluble and tliose witlr chains longer tlran 20 carbon atoms are too insoluble to be useful in aqueous applications. They may be prepared witlr cations otlrer tlran sodium. 

This ordering is the same as discussed above for anionic surfactants and follows from the charge density of the particular acid group. 

Many different types of foaming agents are used, but nonionic surfactants are the most common, eg, ethoxylated fatty alcohols, fatty acid alkanolamides, fatty amine oxides, nonylphenol ethoxylates, and octylphenol ethoxylates, to name a few (see Alkylphenols). Anionic surfactants can be used, but with caution, due to potential complexing with cationic polymers commonly used in mousses. 

Three generations of latices as characterized by the type of surfactant used in manufacture have been defined (53). The first generation includes latices made with conventional (/) anionic surfactants like fatty acid soaps, alkyl carboxylates, alkyl sulfates, and alkyl sulfonates (54) (2) nonionic surfactants like poly(ethylene oxide) or poly(vinyl alcohol) used to improve freeze—thaw and shear stabiUty and (J) cationic surfactants like amines, nitriles, and other nitrogen bases, rarely used because of incompatibiUty problems. Portiand cement latex modifiers are one example where cationic surfactants are used. Anionic surfactants yield smaller particles than nonionic surfactants (55). Often a combination of anionic surfactants or anionic and nonionic surfactants are used to provide improved stabiUty. The stabilizing abiUty of anionic fatty acid soaps diminishes at lower pH as the soaps revert to their acids. First-generation latices also suffer from the presence of soap on the polymer particles at the end of the polymerization. Steam and vacuum stripping methods are often used to remove the soap and unreacted monomer from the final product (56). 

Lignites and lignosulfonates can act as o/w emulsifiers, but generally are added for other purposes. Various anionic surfactants, including alkylarylsulfonates and alkylaryl sulfates and poly(ethylene oxide) derivatives of fatty acids, esters, and others, are used. Very Httle oil is added to water-base muds in use offshore for environmental reasons. A nonionic poly(ethylene oxide) derivative of nonylphenol [9016-45-9] is used in calcium-treated muds (126). 

Carboxylate, sulfonate, sulfate, and phosphate ate the polar, solubilizing groups found in most anionic surfactants. In dilute solutions of soft water, these groups ate combined with a 12—15 carbon chain hydrophobe for best surfactant properties. In neutral or acidic media, or in the presence of heavy-metal salts, eg, Ca, the carboxylate group loses most of its solubilizing power. 

In acidic media, amine oxides and anionic surfactants form precipitates the CMC is much greater than in neutral or alkaline media. Change in CMC parallels change from ionic to nonionic form. Amine oxides are stable in formulated detergent products and do not act as oxidizing agents. Composition and function of representative commercial amine oxides are given in Table 26. 

Ethoxylation of alkyl amine ethoxylates is an economical route to obtain the variety of properties required by numerous and sometimes smaH-volume industrial uses of cationic surfactants. Commercial amine ethoxylates shown in Tables 27 and 28 are derived from linear alkyl amines, ahphatic /-alkyl amines, and rosin (dehydroabietyl) amines. Despite the variety of chemical stmctures, the amine ethoxylates tend to have similar properties. In general, they are yellow or amber Hquids or yellowish low melting soHds. Specific gravity at room temperature ranges from 0.9 to 1.15, and they are soluble in acidic media. Higher ethoxylation promotes solubiUty in neutral and alkaline media. The lower ethoxylates form insoluble salts with fatty acids and other anionic surfactants. Salts of higher ethoxylates are soluble, however. Oil solubiUty decreases with increasing ethylene oxide content but many ethoxylates with a fairly even hydrophilic—hydrophobic balance show appreciable oil solubiUty and are used as solutes in the oil phase. 

Poly(methyl vinyl ether) [34465-52-6] because of its water solubility, continues to generate commercial interest. It is soluble in all proportions and exhibits a well-defined cloud point of 33°C. Like other polybases, ie, polymers capable of accepting acidic protons, such as poly(ethylene oxide) and poly(vinyl pyrroHdone), each monomer unit can accept a proton in the presence of large anions, such as anionic surfactants, Hl, or polyacids, to form a wide variety of complexes. 

The aqueous micellai solutions of some surfactants exhibit the cloud point, or turbidity, phenomenon when the solution is heated or cooled above or below a certain temperature. Then the phase sepai ation into two isotropic liquid phases occurs a concentrated phase containing most of the surfactant and an aqueous phase containing a surfactant concentration close to the critical micellar concentration. The anionic surfactant solutions show this phenomenon in acid media without any temperature modifications. The aim of the present work is to explore the analytical possibilities of acid-induced cloud point extraction in the extraction and preconcentration of polycyclic ai omatic hydrocai bons (PAHs) from water solutions. The combination of extraction, preconcentration and luminescence detection of PAHs in one step under their trace determination in objects mentioned allows to exclude the use of lai ge volumes of expensive, high-purity and toxic organic solvents and replace the known time and solvent consuming procedures by more simple and convenient methods. 

Sodium dodecylsulphate was selected as an anionic surfactant Factors affecting acid-induced cloud point extraction including surfactant, hydrochloric acid, PAHs, and electrolyte concentration, centrifugation have been examined. Finally, we applied the optimized acid-induced CPE system for combination of the extraction and preconcentration steps with fluorimetric determination of some representatives of PAHs. Suggested means was used for PAHs determination in tap water. 

Further auxiliary agents for the production of anionic surfactants are the sulfation and sulfonation agents oleum, chlorosulfonic acid, C1-S02-0H, air-S03 mixtures, air-S02 mixtures, sultones (especially 1,3-propanesultone (CH2—CH2—CH2—SO2), and isethionic acid (2-hydroxyethanesulfonic O-------------------1... 

Higher molecular primary unbranched or low-branched alcohols are used not only for the synthesis of nonionic but also of anionic surfactants, like fatty alcohol sulfates or ether sulfates. These alcohols are produced by catalytic high-pressure hydrogenation of the methyl esters of fatty acids, obtained by a transesterification reaction of fats or fatty oils with methanol or by different procedures, like hydroformylation or the Alfol process, starting from petroleum chemical raw materials. 

Known since the 1940s as commercial products, alkanesulfonates have attracted much interest and are valued as anionic surfactants, both for household and industrial uses. Because of the strong carbon-sulfur bond, alkanesulfonates are appropriate surfactants for applications in acidic and alkaline media. 

As esters of sulfuric acid, the hydrophilic group of alcohol sulfates and alcohol ether sulfates is the sulfate ion, which is linked to the hydrophobic tail through a C-O-S bond. This bond gives the molecule a relative instability as this linkage is prone to hydrolysis in acidic media. This establishes a basic difference from other key anionic surfactants such as alkyl and alkylbenzene-sulfonates, which have a C-S bond, completely stable in all normal conditions of use. The chemical structure of these sulfate molecules partially limits their conditions of use and their application areas but nevertheless they are found undoubtedly in the widest range of application types among anionic surfactants. 

The method developed by Epton [212,213] became the universally accepted method for the analysis of active matter of anionic and cationic surfactants. Epton s method, also known as the two-phase titration, is based on the titration of the anionic surfactant with cetylpyridinium bromide, a cationic surfactant, in the presence of methylene blue as indicator. A solution of the anionic surfactant is mixed with the indicator dissolved in dilute sulfuric acid, followed by further addition of chloroform, and then it is titrated with the cationic surfactant. Methylene blue forms a complex with the anionic salt that is soluble in chloroform, giving the layer a blue color. As the titration proceeds there is a slow transference of color to the water layer until the equivalence point. At the equivalence point colors of the chloroform and water layers are visually the same. On successive additions of titrant the chloroform layer lightens in shade and finally becomes colorless. 

The reaction product with monoethanolamine acts as a thickening agent [41,101] and with alcohols as an emollient [40]. Also reaction products with amino acids and oligo- or polypeptides for use in cosmetic formulations are known [43]. Sorbitan esters from ether carboxylates are described as emulsifiers or mild surfactants in cosmetic formulations [39] and alkyl ether carboxylic acid taurides as nonirritant anionic surfactants for cosmetic cleaners in particular [44]. Using unsaturated ether carboxylates it is possible to make viscous formulations based on combinations of unsaturated and saturated ether carboxylates [111]. Highly purified alkyl ether carboxylates based on alcohol ethoxylates with low free alcohol content have also been described [112]. 

---